Gate Repair in Sherwood - Same-Day Repair, Priced Before We Start

Fast, Reliable Gate Repair Across Sherwood

Gate repair in Sherwood usually means one of three things: a hinge post that has heaved in the clay, a rusted weld finally letting go after twenty wet winters, or an operator board that gave up without warning. Most jobs we handle run $180-$520, and we can usually come out the same day or next morning. Hal Gatewood has been fixing gates in this part of the Willamette Valley since 2001, and if you call (877) 610-2993, a live person answers, not a voicemail tree.

Call (877) 610-2993

We treat Sherwood like the town it is, not a stop on a route. The 97140 zip code covers a lot of ground now, from the older streets near downtown out to the Ridges and the planned communities east of Highway 99W. When a gate fails in Sherwood, the problem is usually older than the call, and we start there.

Why Gatewood Fence & Gate Is Sherwood’s Preferred Gate Repair Company

Hal Gatewood’s name is on the shop, and the shop is down the road. That is the oldest accountability there is, and it matters in a town where people still recognize each other at the hardware store. Our Gate Repair team has been welcomed into Sherwood driveways for a long time now, and we have repaired enough gates in the planned subdivisions to know the HOA style guides often matter as much as the hinge itself.

Sherwood homeowners call us because we answer the phone, we show up in the window we said, and we fix the gate in the driveway instead of hauling it off. Hal is on site for a lot of jobs himself, and every job carries the 90-Day Done Right Promise in writing. If it is not done right, one call brings him back. No runaround.

We are locally owned and owner-operated, with a published address and license number anyone can look up. And when you call after hours because a gate stuck open at 11 p.m., a person still answers. That is the whole point.

Our Gate Repair Services in Sherwood

Hinge & Post Repair

Most Sherwood gate problems start underground. The Tualatin Valley clay beneath many of the newer subdivisions holds water through the wet season and heaves when it dries, which torques hinge posts and throws the whole gate out of square. We excavate the post, check the footer, and re-pour with a deeper frost footing when the soil has shifted it. Then we rehang the gate on sealed-bearing hinges so it swings true. Fix the panel without the post and you will fix it twice.

Gate Realignment

A gate sags in the hinge post, not in the middle, and that is where we start. In Sherwood’s 2000s tract neighborhoods, the spec’d ornamental iron and powder-coated aluminum gates all hit the same failure age at roughly the same time. If your latch is drifting out of alignment or the gate drags on the driveway slope, we square the frame, reinforce the corners where needed, and reset the posts rather than just lifting the panel. A sag correction without a new 24-inch post footing fails within two wet seasons.

Electric Gate Repair

We service and repair operators from Linear, Viking, Ghost Controls, and DoorKing, among others. Many Sherwood subdivisions had slide and swing operators installed in the 2005-2012 window, and those control boards and limit switches are now reaching end of life. We diagnose on site, and if the fix is a board, a sensor, or a limit switch, we tell you straight. We also retrofit entrapment protection onto older operators, which we’ll cover more below because it is a real issue in this town.

Automatic Gate Repair

If your automatic gate stopped working after a hard winter in Sherwood, the first thing we check is whether the post holding the operator has moved. Wet clay plus freeze-thaw cycles will nudge a post a half-inch, and that is enough to bind the arm or knock the limit switches out. We reset the operator, repair the foundation of the post if needed, and test the full cycle, including the safety reversal.

Trusted Brands We Service in Sherwood

We are certified to service nine major gate brands, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. For Sherwood customers in particular, we keep common Linear and DoorKing boards and Viking arms in local stock, which means a faster turnaround when a board fails and you cannot leave the gate open overnight. No waiting three weeks for a part to ship.

Common Gate Repair Problems We See in Sherwood Homes

• Heaved hinge posts in the clay soil. The same Tualatin Valley clay that makes Sherwood’s newer subdivisions settle also pushes posts up and sideways after hard winters. A tech called out for a “broken latch” often finds the latch is fine but the post has torqued the frame a full inch out of square.
• Rust perforation at lower hinge welds. The persistent moisture from October through April gets into ornamental iron gates at the exact point where water sits: the bottom hinge weld. By year fifteen, it is perforated, and a gate that looked fine in July fails in January.
• Operators without modern entrapment protection. Slide gates installed before UL 325 compliance became standard in many Sherwood subdivisions lack functional safety photocells or edge sensors. They may still open and close, but they are a liability, and HOA-backed replacements often require retrofitting the safety systems.
• Rotting wood posts at grade in older neighborhoods. Near the historic downtown core, where late-1970s and 1980s cedar gate posts are still common, the post rots right where it enters the ground. The gate itself is usually fine. We can splice or replace the post without rebuilding the whole fence.

Pricing for Gate Repair in Sherwood, OR

We Also Serve Cities Near Sherwood

We work all over this part of Washington County. If you are in Tualatin, Wilsonville, Newberg, or Tigard, the same crew that serves Sherwood can take care of your gate, and the same 90-Day Done Right Promise applies.

FAQs - Gate Repair in Sherwood