Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Redan
Gate repair in Redan typically runs $185 to $520 for most mechanical and electrical fixes, and Gatewood Fence & Gate can usually have someone at your Redan property the same day you call. We’re not a franchise outfit that routes you to a call center three states away. We’re Hal Gatewood and his crew, and we’ve been fixing gates since 2001. If your gate is sagging, stuck, skipping its track, or staying open when it shouldn’t, call (877) 610-2993 and a live person picks up.
A lot of Redan’s gate problems share the same root: the subdivision was built in the 1980s and 1990s, which means the slide gates at the entrances along Panola Road and the side streets off Redan Road are now 25 to 40 years old. Control boards burn out. Loop detectors fail. Gate posts shift in the red clay. We know these gates because we service them every week, and we know which parts are worth repairing and which ones need to go.
Why Gatewood Fence & Gate Is Redan’s Preferred Gate Repair Company
Our shop is owned and operated by Hal Gatewood, and his name is on every invoice. That’s not a marketing line; it’s the oldest accountability there is. Redan homeowners who’ve been burned by national companies quoting one price on the phone and charging another at the door tell us the same thing: they want a name they can verify and a face they’ll see again. That’s who we are.
Every call to Gatewood Fence & Gate is answered by a live person, 24/7. Not a voicemail tree, not a chatbot, not an answering service in another time zone. When you call at 11 p.m. on a Tuesday because your gate won’t close, you get a real human who can tell you what’s next. Our response time to Redan’s 30074 ZIP is consistent because we’re already working this area daily. Gates in Redan aren’t a side trip for us; they’re the core of the job.
We stand behind the work with a 90-Day Done Right Promise, in writing, on every job. If something isn’t right, one call brings Hal back. We also work repair-first, which matters in Redan more than most places: those 1990s ornamental iron gates and legacy slide-gate operators can often be repaired and brought up to code for a fraction of what a full replacement cost would run. We’re not here to sell you a gate you don’t need.
Our Gate Repair Services in Redan
We handle every part of gate repair, from the hinge post to the control board. In Redan, our work skews heavily toward HOA community-entrance slide gates, so if your neighborhood’s gate is stuck open, cycling wrong, or refusing to respond to the keypad, start here.
Electric Gate Repair
Electric gate repair in Redan usually means diagnosing the operator first, then the wiring, then the safety devices. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so we can tell you honestly whether your control board is repairable or whether you’re throwing good money at a board that’s already pre-failure. In Redan’s humid summers, terminal boards inside above-ground operator housings corrode faster than in drier Southern markets, so we see a lot of intermittent “gate worked yesterday, dead today” calls that trace back to corrosion on a board, not the motor itself.
Automatic Gate Repair
Automatic gate repair in Redan is our single most common call, because the HOA subdivisions off Panola Road and Redan Road run high-cycle operators every day, not just when the occasional visitor pulls up. Those 25-year-old Viking and Elite control boards are obsolete by today’s standards, but many can still be retrofitted with modern safety photocells and new loop detectors rather than being ripped out. The key is knowing which legacy boards have retrofittable paths forward and which ones don’t, and we’ve learned that distinction the only way you can: by fixing hundreds of them.
Hinge & Post Repair
A gate sags in the hinge post, not in the middle, and that is where we start. Redan’s heavy red clay soil expands and contracts with wet-dry cycles, and over decades that movement works hinge posts out of plumb. We see brick columns with hairline cracks near the gate hardware, ornamental iron posts leaning a few degrees, and gate leaves that drag the ground on one side. We weld on site, and we repair the post in place rather than hauling the gate off to a shop, which keeps your gate in your driveway where you can watch the work happen.
Gate Realignment
Slide gates that skip their tracks in Redan often have nothing visibly wrong at the surface. The red clay shifted the concrete pad or the guide rollers by half an inch, and the gate now binds, jumps, or shudders when it moves. We shim, re-level, and reset the track, then check the limit switches and the safety edges so the gate cycles smoothly without tripping out. Fix the alignment without checking the post and you’ll fix it twice, so we do the whole job in one trip.
Lock Repair
Gate locks in Redan range from simple mechanical deadbolts on pedestrian gates to electric strikes and magnetic locks tied into HOA access control systems. A failed lock on a community side gate isn’t a convenience issue; it means residents are either locked out or anyone can walk in. We replace and rebuild locks, align strikes that have shifted with the post, and rewire electric strikes that have corroded at the terminals.
Weld & Rust Repair
Rust on ornamental iron picket gates in Redan is accelerated by humid subtropical summers, and by the time you see a rust blister on the surface, the metal underneath is often perforated. We cut out the perforated section, weld in new material, grind it smooth, and leave the gate ready for paint. On aluminum gates, rust isn’t the issue, but stress cracks at the weld points are, especially on gates that have been sagging for years. We weld on site, with the gate still hung, so the repair matches the actual geometry of the gate, not a jig on a workbench.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Redan
We’re certified to service nine major gate brands, and in Redan the ones we see most are Viking, Elite, and Linear, especially on those 1990s HOA slide-gate systems. We also see a fair amount of FAAC and BFT on newer residential installations. Because Redan’s housing stock skews to the 1980s and 1990s, we keep legacy boards and common parts on the truck rather than ordering everything from a distributor and making you wait another week. That means faster turnarounds for Redan homeowners and HOA boards who need a gate back in operation today, not next Tuesday.
Common Gate Repair Problems We See in Redan Homes
- Slide gates jumping their tracks: Redan’s red clay soil shifts with seasonal wet-dry cycles, moving gate posts and concrete pads by fractions of an inch. The gate then binds on the track, skips a tooth on the drive gear, or slams to a stop and faults out.
- Corroded control boards in above-ground operator housings: Eastern DeKalb County’s humid summers put years of corrosion on terminal boards in just a few seasons. Intermittent failures where the gate works one day and dies the next are often corrosion, not a dead motor.
- Gates that stay open permanently: Many Redan HOA boards deferred maintenance through the economic pressures of the 2000s and 2010s, so failed loop detectors were bypassed to keep gates open rather than cycling. That leaves residents frustrated and boards holding liability for a community entrance that doesn’t actually secure anything.
- Rust through ornamental iron pickets: The humidity here accelerates rust perforation, especially on gates that haven’t been repainted in 20 years. By the time the rust shows through, the picket often needs replacement rather than just paint.
Key Takeaways
- Most Redan gate repairs run $185 to $520; HOA slide-gate systems push higher depending on the scope.
- We answer the phone live, 24/7, and serve all of Redan’s 30074 ZIP.
- We weld on site and repair before recommending replacement.
- Every job carries the 90-Day Done Right Promise in writing.
- Free estimates, no trip charge inside the county, and we quote the price before any work starts.
Pricing for Gate Repair in Redan, GA
Here’s the straight answer on what gate repair costs in Redan. A hinge or post repair typically runs $240 to $480, depending on whether we’re shimming and realigning or cutting out and welding new steel. Electric gate repair, which includes diagnosing and replacing a control board, limit switch, or keypad, usually lands between $285 and $660. Gate realignment for a slide gate on a shifting track is typically $200 to $420. Full weld and rust repair on an ornamental iron gate can run $350 to $800 if multiple pickets are perforated.
What moves the number is the size of the gate, the access you have to the operator, and whether the failure is mechanical or electrical. But we quote the price before any work starts, and that’s the price. Not an estimate with an asterisk. We also offer $40 off any repair over $200, a free second opinion on any written estimate someone else gave you, no trip charge inside the county, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 and you’ll get an exact quote, not a range from a call center.
We Also Serve Cities Near Redan
Redan is our home territory, but we also run calls to Stonecrest, Mountain Park, Stone Mountain, and Panthersville on a regular basis. If you’re on the edge of the 30074 ZIP in one of those areas, the same live-answer phone and the same 90-Day Done Right Promise applies. Whether you’re our Gate Repair team’s next stop in the neighborhood or you found us through our Gate Repair in Redan page, you’ll get the same owner-operated service Hal’s been running since 2001.
Serving Redan, GA - Our Local Coverage Area
We’re based in the Redan area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Redan
They reach 25 years of daily cycling and the legacy boards from Viking, Elite, and Linear were never designed to last that long. In Redan’s humid climate, terminal corrosion accelerates the failure, and once a board starts intermittently faulting, it’s usually near the end. Some legacy boards can be retrofitted with modern safety accessories and kept running; others need replacement. We’ll tell you which one you have, honestly. Call (877) 610-2993 for a straight diagnosis.
Yes, in most cases a 1990s-era gate can be retrofitted with modern UL 325 safety photocells, new loop detectors, and updated control logic while keeping the original iron work and much of the original operator. We recently serviced a slide gate at a subdivision entrance off Panola Road where the original Viking board had burned out and the loop detector was jury-rigged to stay open. Our tech replaced the board, rewired the loop to a modern detector, and added a safety photocell to bring the system up to current entrapment standards. We’d rather retrofit than replace, when retrofit is the right call.
The most common cause in Redan is seasonal soil movement from the area’s red clay, which expands when wet and contracts when dry. Over years, that cycle shifts the concrete pad under the track or the guide rollers by half an inch, which is enough to make a gate bind and jump. There’s often no visible damage at the surface, which is why a lot of quick-fix repairs don’t last. We re-level and re-set the track and check the posts and limit switches in the same visit.
Repair is almost always cheaper, and in Redan’s older subdivisions the original ornamental iron is usually well worth saving. A hinge post repair runs $240 to $480, while a full gate replacement with new iron and operator can run several times that. Fix the panel without the post and you’ll fix it twice, so we always start with the post and the hinge geometry. The gate sags in the hinge post, not in the middle, and that is where we start.
The usual cause is a failed loop detector that was bypassed instead of replaced. During the 2000s and 2010s, a lot of Redan HOA boards deferred maintenance, and when the loop detector died, the quick fix was to set the gate to stay open. That’s not a fix; it’s a liability and it leaves residents unprotected. A modern loop detector is a fraction of the cost of the liability, and we handle the whole access-control modernization when the board is ready to do it right.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Redan since the gates went up.