Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Oxon Hill
Gate repair in Oxon Hill typically runs $180-$340 for hinge and post work, $250-$600 for operator and motor service, and $1,200-$2,800 for a full operator replacement on an aging slide gate. Most calls get a same-day or next-morning visit because we keep our Oxon Hill schedule local, not routed through some call center three states away. If your gate is stuck open, stuck shut, or grinding when it moves, call Hal at (877) 610-2993 and you’ll get a live person who knows this area, not a recording.
Why Gatewood Fence & Gate Is Oxon Hill’s Preferred Gate Repair Company
Hal Gatewood started this shop in 2001, and his name is on every invoice we hand over in Oxon Hill. We have pulled up to garden apartment gates off Indian Head Highway, fixed swing gates in older townhome communities, and swapped out salt-corroded hinge posts near National Harbor enough times to know exactly what this part of Prince George’s County does to a gate. When you call (877) 610-2993, you get a person. Not a queue. Not a chatbot. A person who can tell you whether the job is a two-hour hinge replacement or a full operator swap.
We’re not the company that quotes one price on the phone and sends a truck that charges another at the door. The price Hal quotes is the price you pay. And every job, big or small, carries our 90-Day Done Right Promise in writing. If it is not done right, one call brings him back. That is not a promotion. That is our name on the shop.
Our Gate Repair Services in Oxon Hill
Electric Gate Repair
Electric gate repair in Oxon Hill usually means troubleshooting an operator that hums but will not move, or a keypad that quit talking to the board. We carry retrofit boards for older Linear, DoorKing, and Viking units, and we can tell you honestly whether a $300 board swap beats a $1,500 operator replacement. Along the MD-210 corridor, we see far more humidity-related board failures than mechanical ones, and we know which models are worth saving.
Automatic Gate Repair
Your automatic gate depends on three things working together: the operator, the safety sensors, and the hardware. When one fails, the whole system looks dead. In Oxon Hill’s older townhome and apartment complexes, we regularly find that a gate that will not open is not a motor problem at all. It is a failed loop detector at the driveway or a photocell knocked out of alignment by a sagging post.
Hinge & Post Repair
A gate sags in the hinge post, not in the middle. That is where we start. Oxon Hill’s riverside humidity is rough on steel posts, and rust jacking at the weld points is common on gates that have stood since the 1980s or 90s. We weld on site, so your gate stays in your driveway while we rebuild the hinge mount or replace a rotted post pocket. We do not haul it off to some shop across the county.
Gate Realignment
When a swing gate starts dragging on the latch side, realigning it before the hinge post fails completely is cheaper than replacing the whole panel. In Oxon Hill, we see gate realignment calls most often from brick garden apartment communities along Indian Head Highway, where gates have been hanging for 30 years and the post has shifted in the footing. We level the gate, reset the hinges, and make sure the safety edges and photocells work after the adjustment.
We also handle gate lock repair, weld and rust repair, and access control systems. Our full Gate Repair service lineup covers everything from a dead transmitter to a full operator retrofit.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Oxon Hill
We are certified to service nine major gate brands, including Linear, Viking, Ghost Controls, DoorKing, and more. For Oxon Hill customers, that matters because so many of the older operators in this area are Linear or DoorKing models installed decades ago, before the operator mattered much to manufacturers. We stock common retrofit parts locally for these legacy units, so we are not waiting a week on an out-of-state parts drop when your gate is stuck open. If your brand is one we know well, we will tell you. If we think a retrofit is throwing good money at a dead platform, we will tell you that too.
Common Gate Repair Problems We See in Oxon Hill Homes
- Obsolete control boards in 1980s-90s DoorKing and Linear operators. Years of Potomac riverside humidity get into the electronics and burn out the board. Some boards can be retrofitted; others mean it is time for a new operator altogether.
- Corroded underground wiring along Indian Head Highway. Many of those 1980s-90s slide gates were mounted on concrete pads with no real drainage. Decades of pooled water corrodes the wiring conduit from below, and a gate that looks like a simple motor failure often has a wiring problem under the pad. This is the single most common surprise we explain to Oxon Hill property managers.
- Ground-mount operator flooding near the Potomac floodplain. After a nor’easter or tropical remnant, standing water finds its way into bottom-of-post and ground-mount operators near the waterfront. The circuit board shorts, the motor seizes, and the whole unit usually needs replacement.
- Sagging swing gates that trip the safety photocell. Older steel swing gates hung before modern safety requirements were in place often sag at the hinge post. The gate drops a few inches, the photocell beam gets blocked, and the operator refuses to close. Fix the post, not just the sensor.
Pricing for Gate Repair in Oxon Hill, MD
We quote every job before any work starts, and the price does not change at the door. For Oxon Hill specifically, here is what we see day to day. Hinge and post repair runs $180-$340. Gate realignment runs $200-$400. Electric gate repair, including a new circuit board or limit switch, runs $250-$600. A full operator replacement on an aging slide gate runs $1,200-$2,800 depending on the length of the gate and whether we need to run new wiring to the motor pedestal. If you have a written estimate from another company, bring it to us. We will give you a free second opinion. And if your repair is over $200, there is $40 off. No trip charge inside the county. Seniors and veterans get 10% off, permanently. Call (877) 610-2993 for an exact quote, free.
We Also Serve Cities Near Oxon Hill
We work throughout the Oxon Hill area, including Glassmanor, Oxon Hill-Glassmanor, Temple Hills, and Hillcrest Heights. The same live-answer phone, the same 90-Day Done Right Promise, and the same Hal Gatewood who shows up himself. For more about our service area and approach, see Gate Repair in Oxon Hill and the neighborhoods we cover.
Serving Oxon Hill, MD - Our Local Coverage Area
We’re based in the Oxon Hill area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Oxon Hill
They fail more often because the operators are older and wetter. The 1980s-90s slide gates along Indian Head Highway were mostly mounted directly on concrete pads with no drainage channel, so water pools at the motor pedestal after every rain. That standing water creeps into the wiring conduit from the ground up, and combined with Oxon Hill’s riverside humidity, it corrodes the electronics and the underground wiring. Clinton and Fort Washington have newer housing stock and better-set operators in many cases. Here, the failure profile is legacy hardware meeting bad drainage. Call (877) 610-2993 and we will diagnose it on site.
Replace it. A dead keypad on a 30-year-old operator usually means the board is failing, and once you pay for a new board, a new keypad, and labor, you are halfway to a new operator with modern safety circuits. When the motor housing is rusted too, the retrofit math gets worse. We will show you the numbers side by side, and our 90-Day Done Right Promise applies either way. But in Oxon Hill, most of those legacy operators near the river are at end-of-life. Call (877) 610-2993 for a free assessment.
Storm flooding in low-lying Oxon Hill areas near the Potomac typically destroys the circuit board and seizes the motor inside ground-mount operators. If water reached the bottom of the post or the motor pedestal, the underground wiring may also be compromised. We usually recommend a full motor unit replacement after submersion, and we check the wiring conduit for standing water before we reinstall anything. Call (877) 610-2993 and we will come evaluate it.
The post is the real problem. A gate sags at the hinge post, and when the post shifts, the gate drops and blocks the photocell beam. You can realign the sensor, but the gate will keep dropping until the post is rebuilt. In Oxon Hill’s riverside humidity, rust jacking at the hinge is common on 20- and 30-year-old steel gates. Fix the hinge post, and the photocell stops tripping. Call (877) 610-2993 and we will fix it on site.
If your gate was installed before roughly 2000, it probably does not meet current UL 325 entrapment protection standards unless it has been retrofitted. The obvious checks: working safety photocells on both sides of the opening, a functional reversing edge or contact sensor, and a warning sign. If your operator is older than the safety standard, we can evaluate it and tell you honestly whether a retrofit is worth the cost or if a replacement operator is the cheaper answer. Call (877) 610-2993 and we will inspect it.
Call Gatewood Fence & Gate for Oxon Hill Gate Repair
If your gate is stuck, sagging, rusty, or just not answering the keypad anymore, call us. You will talk to a live person at (877) 610-2993, any hour, any day. Hal Gatewood will quote the job before any work starts, and the 90-Day Done Right Promise comes in writing. We are local, we are owner-operated, and we have been doing this since 2001. The name is on the shop, and the shop is down the road. That is the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Oxon Hill since 2001.