Gate Repair in Norcross - Same-Day Repair, Priced Before We Start

Gate Repair in Norcross, GA

Gate repair in Norcross usually runs between $185 and $650, and the reason the range is that wide comes down to what’s actually broken. Most of what we see here isn’t the gate itself giving up. It’s a post that the red clay heaved out of true, or an operator motor that spent ten years running 300 cycles a day on a residential rating. Call (877) 610-2993 and a live person answers. That’s the whole promise.

Call (877) 610-2993

Norcross is different from the suburbs around it. The housing stock runs from century-old homes near the historic district to 1970s ranch subdivisions with ornamental iron swing gates, plus a dense belt of 1990s and 2000s apartment complexes along Jimmy Carter Boulevard and Buford Highway where automatic slide gates run all day, every day. Each of those situations fails differently, and fixing them right means knowing which one you’re standing in front of.

Why Norcross Homes Are Different

Gwinnett County’s red clay does not sit still. It swells through wet springs, then contracts and cracks in a dry August. Every seasonal heave shifts gate posts by fractions of an inch. Fractions at the post become two or three inches of sag at the gate’s leading edge, which is why we see so many Norcross gates that close fine in May and scrape the driveway by September. The post was set too shallow, or with the wrong footing, and the clay pulled it right out of true.

Humidity is the other local variable. Norcross sits in Georgia’s humid summer belt. Overnight temperatures stay in the 70s and moisture never fully burns off. That damp gets inside operator housings and corrodes circuit boards, limit switches, and terminal screws. Rubber belts get brittle in the occasional hard freeze, like the ones in January 2014 and January 2022, then crack under load. A gate in Norcross is dealing with soil movement below it and moisture above it at the same time, and the repair that ignores either one won’t last.

The third thing: this city has a lot of gated multi-family properties. Norcross grew fast through the 1990s and 2000s as one of metro Atlanta’s most diverse communities, and that growth filled the corridors along Jimmy Carter Boulevard and Buford Highway with apartment complexes and HOA communities. Those gates cycle 200 to 400 times a day, far beyond what residential-rated operators were ever built to handle. So the dominant repair call in Norcross is burnout: fried operator motors, stripped drive systems, and logic boards that died years early.

Gate Repair in Norcross

Gate repair in Norcross breaks down into two worlds. The first is the homeowner on a 1970s ranch off Beaver Ruin Road with a swing gate that’s sagging because the hinge post moved. The second is the property manager on Jimmy Carter Boulevard whose slide gate cycles 400 times daily and just ate another motor. Both are gate repair, and both have different fixes. We do both, and we do them in your driveway with the welding gear on the truck. Here’s a look at the Gate Repair work we handle most in Norcross.

Electric Gate Repair

Electric gates in Norcross deal with two enemies: humidity and duty cycle. Georgia summers saturate control boards, photo eyes, and wiring connections with moisture, corroding contacts until the gate stops responding. We diagnose electrical faults on site, replace what’s failed, and seal what’s exposed. If the failure is a fried logic board on an old Apollo or Elite unit that’s been cycling 300 times daily for years, we’ll say so plainly and quote a commercial-grade replacement instead of patching a unit that will quit again. Logic board swaps run $175 to $400.

Automatic Gate Repair

An automatic gate is only as reliable as the operator driving it and the safety edges watching it. In Norcross’s apartment communities, we routinely find residential-rated operators that should have been swapped for commercial units a decade ago. The motor is burnt, the drive belt is shredded, and the property’s paperwork still calls the unit functional. We service LiftMaster, Linear, DoorKing, and the rest of the major brands, and we carry parts locally so an automatic gate repair doesn’t become a two-week wait for a backordered board. Operator replacement runs $450 to $1,200 depending on whether the gate needs a residential or commercial unit.

Hinge & Post Repair

A gate sags in the hinge post, not in the middle. That’s where we start. Gwinnett County’s red clay expands when wet and contracts when dry, and that cycle heaves posts out of alignment seasonally. A swing gate that dragged fine in July may bind in January after months of soil movement. We dig, reset, and re-anchor posts, then weld or replace hinge barrels as needed. Post re-setting and re-anchoring, the most common swing gate fix in Norcross’s clay soil, typically lands at $300 to $650 depending on post size and how much concrete goes back in the hole. Fix the panel without the post and you’ll fix it twice. We’d rather fix it once and stand behind it for 90 days.

Gate Realignment

Gate realignment in Norcross is often as much about soil as it is about metal. When a gate drags, binds, or fails to close fully, the cause is usually a post that has shifted or a hinge that’s worn egg-shaped. We measure the gate, check the reveal, and bring everything back to square. The same applies to sliding gates that have jumped their track or bent a roller. A basic service call to diagnose a gate that won’t open runs $85 to $145, and realignment work itself falls between $180 and $340 for most residential gates. Realignment isn’t a stopgap. It’s the repair that keeps other problems from following.

How fast can you get to Norcross for a gate emergency?

Same-day service is available for most Norcross neighborhoods. Emergency calls from apartment complexes or HOAs get priority because a stuck-open gate is a security problem, not just an inconvenience. Be specific about the symptom when you call and the live person who answers will give you a straight answer on arrival time. Call (877) 610-2993.

Do you warranty gate repairs in Norcross?

Yes. Every job carries the 90-Day Done Right Promise in writing. It’s not “up to” 90 days, not “most cases” 90 days. If something isn’t right inside that window, one call brings Hal back. No runaround, no open ticket, no fine print. That’s the same promise a homeowner on Holcomb Bridge Road gets and the same one an apartment complex on Buford Highway gets.

Gate Installation in Norcross

Gate installation in Norcross runs $1,400 to $6,500 for most residential jobs. The spread is wide because a manual pedestrian gate and an automated sliding gate are very different projects, and Norcross soil makes the difference matter. A post set too shallow in Gwinnett County clay will heave within two seasons. A motor spec’d too small for a multi-family gate will burn out within a year. We set every post below the frost line with a footing sized for the clay, and we match the operator to the actual cycle count, not the spec sheet. Here’s a look at the Gate Installation work we do across Norcross.

Driveway Gate Installation

A new driveway gate in Norcross typically runs $2,200 to $6,500, depending on whether you want swing or slide, ornamental iron or aluminum. The red clay soil here shifts with every wet and dry season, which means the hinge posts have to be set deeper and with more concrete than a national company’s spec sheet calls for. We know that. We also know that a gate sags in the hinge post, not in the middle, and that is where we start. Every post foundation is built for the soil it’s going into, not the soil the manufacturer assumed.

Pedestrian Gate Installation

Pedestrian gates in Norcross run $800 to $2,500, and they’re the quiet workhorses of this city. Walk any block of older homes near Historic Norcross and you’ll see them: narrow iron gates between the house and the fence, rusted at the hinges, scraping the ground. Georgia’s humid summers accelerate that rust every single year. We build new pedestrian gates and match them to existing fence lines, and we set the hinges so they don’t bind when the gate post heaves in spring.

Sliding Gate Installation

Sliding gates are the standard for Norcross apartment complexes and townhome communities, and a new automated slide gate usually falls between $3,000 and $6,500 installed. The stock of 1990s complexes along Jimmy Carter Boulevard installed cheap residential operators during the suburban boom, and those are hitting end of life all at once. A commercial-grade replacement, not a repair, is the norm here. We quote it honestly. We also coordinate with the Gate Motor & Opener side of the work, because a gate and its operator need to be matched to each other and to the cycle count.

Swing Gate Installation

Swing gates remain the choice for single-family homes in Norcross, particularly on the ranch properties built in the 1970s and 1980s. Expect $1,400 to $4,200 for a single swing gate, more for a double. The thing nobody tells you in Norcross: our wet-dry soil cycles cause gate posts to heave seasonally, and that movement puts constant stress on hinges and latches. We set posts below the freeze line and use materials that tolerate the expansion and contraction.

How much does gate installation cost in Norcross compared to nearby cities?

Prices in Norcross run similar to Duluth and Peachtree Corners, typically within a couple hundred dollars of each other. What changes the number is not the city but the job: a manual pedestrian gate can run under $1,000, while an automated security gate for a multi-family property can exceed $9,000. No trip charge inside Gwinnett County means the estimate call costs you nothing. Call (877) 610-2993 for an exact quote.

Do you offer a warranty on gate installation in Norcross?

Yes. Every job we install carries the 90-Day Done Right Promise in writing. If the gate sags, the posts shift, or the operator fails during that window and it’s our work, one call brings Hal back. We don’t hide behind fine print. We also honor a free second opinion on any written estimate you’ve received from another company.

Gate Motor & Opener in Norcross

If your gate motor quit in Norcross, you need an answer before the day gets away from you. A gate that won’t open is a security gap and a morning headache. Our gate motor and opener service covers every Norcross ZIP code, and the person who answers the phone at (877) 610-2993 is a person, not a recording. Here’s a look at the Gate Motor & Opener work we handle in Norcross.

The pattern we see most in Norcross is thermal. Multi-family gates along Jimmy Carter Boulevard and Buford Highway run 300 to 400 cycles daily on operators that were rated for a fraction of that. The motors burn out years early. The logic boards crack. The drive rails strip. If the gate you’re responsible for cycles that heavily, the honest fix is usually a commercial-grade replacement, and we’ll quote one plainly rather than patching a unit that will quit again in six months.

Motor Repair

Repair is where we’d rather start. Hal fixes the gate in your driveway rather than hauling it off or swapping parts that don’t need swapping. In Norcross, we regularly repair FAAC, BFT, and Linear operators by replacing stripped drive gears, fried boards, and corroded contacts instead of pushing a whole new system. A typical motor repair in Norcross runs $280 to $750, and we quote the exact price before any work starts. The $40-off-any-repair-over-$200 offer applies here, and there’s no trip charge inside Gwinnett County.

Slide Motor Service

Slide gates dominate Norcross’s multi-family properties, and their motors work harder than any other type. Stripped rack and pinion teeth, shrieking gears, and thermal overloads are the calls we get most from apartment managers along Buford Highway. The fix is usually a new rack and pinion drive plus a motor that can actually handle 200 to 400 daily cycles. Slide motor repair in Norcross runs $320 to $800, and a complete commercial slide operator replacement runs $3,000 to $5,800 depending on gate length and condition of the rack.

Battery Backup

Georgia’s thunderstorms and the occasional hard freeze can take out power right when your gate needs to work. Battery backup units can be retrofitted to most existing operators from FAAC, BFT, LiftMaster, and Viking, even older units. You don’t have to buy a whole new system to get emergency opening power. Battery backup installation in Norcross typically runs $650 to $1,400 including the unit and wiring. This is a smart retrofit for HOAs that can’t afford a gate stuck closed during a power outage on Buford Highway.

Our Norcross apartment gate cycles 300 times a day and the operator keeps burning out. Can you fix it or do we need to replace it?

Most of the time, you need to replace it. If the original opener was installed to residential specs but the gate cycles 300 times daily, the motor has been running at triple its intended duty cycle for years. In high-cycle Norcross apartment applications, the honest fix is usually a commercial-grade slide operator like a DoorKing 9150. We can diagnose the cycle count and motor condition on site. Call (877) 610-2993.

The slide gate at our Norcross townhome community jerks and shrieks every morning. What’s actually wrong?

That jerk and shriek is the sound of stripped rack and pinion teeth. The gate is binding, the motor is fighting it, and every morning the gears take another bite out of themselves. If it’s ignored long enough, the gate locks mid-open and tenants block the call box trying to get a response. The fix is replacing the rack and pinion drive, and often the motor bearings as well.

Gate Access Control in Norcross

Gate access control in Norcross typically runs $850 to $4,200 depending on the system you choose, and most keypad, card reader, and phone entry installations are completed in a single visit. We’ve been driving the roads around Jimmy Carter Boulevard and Buford Highway long enough to know that a gate opener that worked fine yesterday will pick today’s heat and humidity to quit. If your keypad is dead or your remote stopped working, call (877) 610-2993 and a live person answers. Here’s a look at the Gate Access Control work we do in Norcross.

Keypad Entry

A keypad that won’t accept the code, a keypad that accepts codes you never programmed, or a keypad that works for the first ten entries and then freezes. We see all three regularly across Norcross, especially on communities where the HOA added new tenants every month since the early 2000s. A basic replacement keypad for a Norcross swing or slide gate typically runs $180 to $380 installed, and we set everything up on site before we leave.

Remote Control

If your garage-style clicker opens the gate only when the car is parked at a particular angle, the problem is rarely the remote. It’s usually the antenna lead, the receiver board, or a cracked solder joint on the operator. For Norcross townhome and apartment communities, a multi-frequency receiver and a fresh set of remotes cost $350 to $700 in most cases. We configure remotes right there at the gate, not three days later.

Phone Entry

We install and repair phone entry systems that let visitors or delivery drivers dial from the keypad and get buzzed in from anywhere. Norcross homeowners and small HOA communities use these heavily because package theft is a real concern across Gwinnett County. A single-line phone entry unit with the wiring you already have usually lands between $600 and $1,400 installed. If the current unit died after a lightning strike, we’ll often see the burned trace on the board before we finish the diagnosis call.

How fast can you get to Norcross for an access control failure?

Same day in most cases. When a gate won’t open or won’t close, we treat it as urgent and route the nearest available truck to Norcross. Call (877) 610-2993 and a live person will confirm the window before you hang up. Estimates are free, and the price you’re quoted is the price you pay.

Can you replace a burned-out access control board with a commercial-grade unit for my Norcross HOA?

That’s the most common job we do in Norcross. Many apartment and HOA gates here were built with residential-rated boards doing commercial traffic, and we regularly upgrade to DoorKing, Viking, or Elite commercial boards sized for 300 to 400 cycles a day. You’ll get a written quote before any work starts, and the old board stays on the property for you to inspect.

Gate Parts & Welding in Norcross

Gate parts and welding in Norcross is the repair-first side of what we do. When an ornamental iron gate rusts through at the bottom rail, or a hinge barrel cracks from years of post movement, the answer isn’t a new gate. It’s a weld in the right place, done on site in your driveway, so the gate doesn’t disappear to a shop for two weeks. Here’s a look at the Gate Parts & Welding work we handle in Norcross.

On-Site Welding

Humid Georgia summers accelerate rust on older iron gates, especially near the bottom rail where water pools. We weld and patch on site, in your driveway, so the gate doesn’t leave your property. Hinge replacement with on-site welding falls between $180 and $340. The welding gear is on the truck, and the person who quotes the job is the person who welds it.

Parts Replacement

We stock common replacement parts locally: hinges, rollers, wheels, receiver boards, safety edges, and drive components for the major brands. That’s why a Norcross gate repair doesn’t become a two-week wait for a backordered board. If we don’t have the part on the truck, we can usually get it same day from a local supplier, not a warehouse three states away.

Do you weld gates on site in Norcross, or do you haul them away?

We weld on site. The gate stays in your driveway. Hal fixes the frame, hinge plates, and pickets right where they are, which means you keep your gate and your schedule. Most weld repairs are done in one visit, and the price is quoted and agreed before the welder fires up. Call (877) 610-2993 for an estimate.

Can you repair a rusted ornamental iron gate in Norcross without replacing the whole thing?

Usually yes. If the rust is localized to the bottom rail or hinge points, we cut out the bad section, weld in fresh steel, and grind it smooth. The gate keeps its original look and gains years of service. Full replacement is only the honest answer when the corrosion has eaten through the frame in multiple places.

Brands We Service in Norcross

We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule operators across Norcross. We stock common parts locally for Linear, DoorKing, and Viking, which are the brands most often found on Norcross multi-family gates. That keeps turnaround short. See our brands page for the full list and what we stock.

Pricing for Gate Repair in Norcross, GA

Neighborhoods We Serve in Norcross

We cover every corner of Norcross, from the historic downtown core to the apartment corridors along the highways. Call before noon and you’ll generally see someone the same day, because we’re not routing crews from the other side of the metro.

• Historic Downtown Norcross
• Jimmy Carter Boulevard corridor
• Beaver Ruin Road area
• Singleton Road
• Graves Park and surrounding streets

Service Area - Cities Near Norcross

We work across Norcross, GA and the surrounding communities. If your gate is in Duluth, GA, Lilburn, GA, Lawrenceville, GA, Peachtree Corners, GA, or Suwanee, GA, the same crew, the same pricing, and the same 90-Day Done Right Promise apply.

FAQs About Gate Repair in Norcross