Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Millington, TN
Gate repair in Millington typically costs $185-$425 for most hinge, post, and realignment work, and we can usually have someone at your house the same day you call. The clay-heavy soil between the Wolf River and Loosahatchie River bottoms shifts every wet season, which means gates here fail differently than they do in flatter, drier suburbs. If your swing gate sags, your slide gate won’t budge, or your operator just hums and does nothing, call (877) 610-2993 and a live person will pick up, schedule the truck, and give you a real arrival window.
Why Millington Homes Are Different
Millington sits in low-lying terrain between the Wolf River and Loosahatchie River bottoms, where clay-heavy soil stays wet through summer and heaves through winter. Gate posts set at standard depth lean within a season, throwing photo-eyes out of alignment and stalling operators mid-cycle. The core housing stock, built in the 1960s through 1980s to house base-adjacent families, still runs on original gate hardware that’s now heavily corroded from decades of river-bottom humidity.
NSA Mid-South creates an unusually security-conscious homeowner base of active-duty military, veterans, and defense contractors who invest heavily in access-control-capable swing and slide gates rather than purely decorative ones. Newer subdivisions pushed outward along Shelby Drive and into the 38054 ZIP have HOA-controlled neighborhood entry gates, aluminum dual-swing or slide-gate units that generate recurring service calls on minimal maintenance budgets. Properties backing onto the Loosahatchie corridor are the worst for motor posts set in perpetually damp ground. We bore the footing deeper, set a gravel drain at the base, and mount operator brackets with longer anchors. It’s a detail Memphis-based crews often skip, and it’s the difference between a gate that opens true for a decade and one that needs re-squaring every spring.
Gate Repair in Millington
Gate repair in Millington, TN typically runs $185-$425 for most hinge, post, and realignment work, and we can usually have someone at your house the same day you call. Our crew works Millington daily, from the base-adjacent neighborhoods off Navy Road out to the newer subdivisions near Shelby Drive. We don’t run a call center, and we don’t let a voicemail stand between you and a working gate. Gate Repair is what we’ve done since 2001, and the 90-Day Done Right Promise goes on every job in writing.
Hinge & Post Repair
This is the repair Hal cares most about, because it’s the one other shops skip. A gate sags in the hinge post, not in the middle, and that’s where we start. In Millington’s clay-heavy ground, post footings heave and shift every wet season. We re-set the post with a deeper footing and a drainage channel where the ground stays saturated, then weld or replace the hinges so the gate actually hangs true. A hinge and post repair on a typical wood or steel swing gate runs $240-$425. Fix the panel without the post and you’ll fix it twice.
Gate Realignment
A gate that drags, binds, or won’t latch is almost never a panel problem. It’s a footing problem. Millington soils seasonally saturate, then dry and shrink, and the cycle throws automatic operators out of alignment year after year. We realign the gate, then address the post and footing so it stays put. Gate realignment is $185-$320 depending on post condition. A realignment that holds in Bartlett or Lakeland will fail within a season here unless the post is set deeper with drainage.
Automatic Gate Repair
Automatic gate repair covers the operator, safety edges, photo eyes, and the control board. In Millington, we regularly see obsolete control boards from the 1980s and 1990s that failed after a lightning strike or an ice-storm power surge. Replacement parts are no longer manufactured, so the honest answer is a retrofit to a modern board that works with your existing keypad and remotes. An electric gate repair or control board retrofit typically lands between $310-$600. We tell you plainly when a retrofit makes sense and when replacement is cheaper than throwing parts at a dead operator.
Why does my gate post keep leaning even after it’s been re-set?
The job was likely done with a standard footing depth and no drainage, which doesn’t work in Millington’s clay-heavy, seasonally saturated soil. We set posts deeper than code minimum and cut a drainage channel on wet lots, especially near the river corridor. Call (877) 610-2993 and we’ll dig it up, show you what’s underneath, and do it right this time.
My 1980s automatic gate still works, but the control board is obsolete. Can it be retrofitted?
Yes, in most cases. A modern board can be retrofitted to work with your existing keypad entry, remotes, and safety edges, usually for less than replacing the entire operator. We did exactly this on a 1970s ranch off Navy Road where an old FAAC board had died. If a retrofit won’t hold, we’ll tell you before we touch anything.
Gate Installation in Millington
Gate installation in Millington runs from about $2,800 for a basic single swing gate to $9,500 for a double slide gate with an access-control operator and loop detectors. Most jobs on ranches and acreage lots in the 38053 and 38055 ZIPs land between $4,200 and $6,800, including the footing work that makes the difference between a gate that lasts ten years and one that leans by spring. We’re Gatewood Fence & Gate, and Gate Installation here means measuring the actual ground, not pulling a kit off a shelf.
Driveway Gate
Millington driveway gates tend to be wider than the suburban standard. Sixteen feet, eighteen feet, sometimes twenty-two feet across a gravel entrance off Shelby Drive or down a lane that splits pasture. That span changes what gets installed. A lightweight residential operator won’t move a 900-pound steel slide panel through Millington humidity year after year. We spec the motor and the rack to the actual panel weight and the actual span. A single swing gate, manual, runs $2,800-$4,200; automated, $4,500-$6,800.
Sliding Gate
Sliding gates make sense on Millington lots where a swing gate would fight the grade or the wind. You see them on HOA entrances in the newer subdivisions pushed out along 38054 and on farm lanes where a swing panel would take out a fence line every time a trailer comes through. The failure mode here is almost always the track or the rack. Ice storms coat the track and shear rack-and-pinion teeth. A slide gate, manual, runs $3,600-$5,500; automated with loops, $5,200-$9,500.
Swing Gate
For most Millington ranch homes and acreage, a swing gate is the right answer. It’s what the 1960s and 1970s original hardware anticipated, even if that hardware is now rusted through. A properly installed swing gate here needs a deep footing at the hinge post, a second post that won’t migrate, and an operator sized for the panel weight. A double swing gate, automated, typically runs $5,800-$8,200. We hang swing gates from Viking and Ghost Controls operators regularly, and we weld brackets on site so you’re not bolting a universal plate to a post that’s already leaning.
Why do gate posts in Millington lean within a year of installation?
Because the original footing was too shallow for Millington’s clay-heavy, seasonally saturated soil, and no drainage channel was installed. The clay heaves as it absorbs water from the Wolf River and Loosahatchie River bottoms. A gate post set at 24 inches deep will lean. We bore 48-inch footings and cut drainage so the soil doesn’t push the post. Call (877) 610-2993 for a free measure and written estimate.
Can you install a gate opener on a long, rural driveway in 38055 where there’s no grid power?
Yes. We install solar gate openers with battery banks sized to the actual panel weight and daily open cycles, not a one-size panel kit. A working farm gate that cycles 20 times a day needs more storage than a weekend driveway. Solar opener packages add $1,100-$2,400 to a new or existing gate. We calculate the load, spec the array, and run the system entirely on solar with no trenching.
Gate Motor & Opener in Millington
Gate motor and opener work in Millington typically costs between $275 and $680 for most repairs, while full motor replacements with new arms and remotes run $850 to $1,900 depending on the gate’s weight and length. Most repair calls we get from Millington homeowners can be handled the same day or the next morning, because our trucks are already working the 38053 and 38054 ZIPs every week. If your gate won’t open, is making a grinding noise, or only moves halfway, Gate Motor & Opener service from Gatewood Fence & Gate means diagnosis in your driveway, not guessing over the phone.
Motor Repair
Most gate motor repairs in Millington come down to three things: a failed capacitor, a stripped gear, or a limit switch that’s drifted. We diagnose it in your driveway, not over the phone, and we fix what’s actually wrong. We’re a repair-first shop. If a $180 circuit board fixes your operator, that’s what we do. A capacitor or limit switch replacement usually runs $95-$190. We don’t haul your gate off to a shop or swap parts that don’t need swapping.
Linear Motor Service
Linear operators are common on the sliding gates you see along Fayette County line properties and the newer HOA communities around the 38054 ZIP. The wet, clay-heavy ground in the low-lying areas between the Wolf River and Loosahatchie bottoms causes posts to heave seasonally, which knocks Linear operators out of alignment. We know to check the post footing before we touch the operator. Gearbox and arm replacement on a swing gate runs $325-$575, because fixing the motor without fixing the post means you’ll be calling us again in six months.
Slide Motor Service
Slide gates take more abuse in Millington than swing gates, especially the aluminum dual-swing and slide-gate units on HOA entrances off Shelby Drive. Winter ice storms hit the Memphis metro every two to three years, and a quarter-inch of ice on the track will burn up a slide motor fast if the limit switches don’t catch it. A full slide motor replacement with new chain, wheels, and remotes typically lands between $1,100-$1,900 depending on gate weight and length. We service slide operators on-site, including track cleaning, wheel replacement, and motor swaps where the gearbox has been ground down by grit and gravel.
How fast can you get to my house in Millington?
Most gate motor repair calls in Millington are handled same-day or next morning. Our trucks are in the 38053 and 38054 areas every week working on ranch homes and HOA gates. If your gate is stuck open and you need someone now, call (877) 610-2993 and a live person will tell you exactly when we can be there.
Do you offer emergency gate motor service in Millington?
Yes, we answer calls 24/7 with a live person, and emergency repair calls in Millington get prioritized. If your gate won’t close and you can’t secure your property overnight, that’s an emergency to us. The 90-Day Done Right Promise applies to emergency repairs the same as any other job.
Gate Access Control in Millington
Gate access control in Millington means keypads, card readers, phone entry, and video intercoms wired to swing and slide gates that get worked hard by military families, veterans, and defense contractors. Most repair calls in 38053, 38054, and 38055 run between $180 and $450 when we can fix the existing equipment, and a full upgrade to a modern video intercom with a card reader typically lands between $900 and $2,400. Gate Access Control here is shaped by NSA Mid-South’s security-conscious culture, not by suburban convenience alone.
Keypad Entry
Keypad entry is everywhere in Millington, especially on gates around base housing and older ranches where the gate predates cell phone apps. We replace worn-out keypads, rewire existing wiring, and sync codes to new receivers. Humidity-driven corrosion on membrane contacts is a real problem here, and we see intermittent “ghost” entry codes on HOA slide gates in the 38054 all summer. A new keypad with a sealed faceplate usually runs $110-$320 installed.
Card Reader
Card readers on Millington gates are often tied to NSA Mid-South security habits. Military families and defense contractors bring those expectations home. We install standalone card reader systems, proximity readers, and readers integrated with video intercoms. If your card reader works sporadically after rain, the issue is usually moisture in the reader housing or a failing power supply. Fixing a misbehaving card reader in Millington typically costs $140-$300.
Video Intercom
Video intercoms are becoming more common on newer Millington subdivisions, especially where homeowners want to see who’s at the gate from inside the house. We upgrade older systems to modern video intercoms with smartphone app connectivity, and we retrofit existing gates that were never built for cameras. If you’re on a lot backing up to the Loosahatchie River corridor, we’ll recommend a video intercom with night vision and a sealed outdoor station, because the morning fog and river damp kill cheap units within two seasons. Smart access retrofits start around $700 and go up to $2,400 when wiring distance and gate type get complicated.
Why does my Millington gate operator go out of alignment every spring, even after a recent repair?
Because the clay under your gate post moves every wet season, and if the footing wasn’t dug deep enough, the post leans and drags the operator out of alignment. Millington’s soil between the Wolf River and Loosahatchie bottoms heaves when it saturates. The permanent fix is a deeper footing, usually 4 feet, plus a drainage channel so water doesn’t pool at the base. Call (877) 610-2993 for a free assessment.
What is causing my gate’s keypad entry to work intermittently in Millington’s humid summers?
Moisture. Millington stays humid from May through September, and that damp works its way into membrane keypad switches. The contacts corrode and you get intermittent codes, ghost entries, or complete lockouts. Sometimes it’s the keypad itself; sometimes it’s a failing connection at the control board. A sealed keypad rated for outdoor wet service fixes it for good. Call (877) 610-2993 for an exact quote.
Gate Parts & Welding in Millington
Gate parts and on-site welding in Millington run $180 to $900 for most hinge, post, and rail repairs, with a typical service call reaching your driveway within 45 minutes. Hal Gatewood has been welding gates in driveways since 2001, and the same standard applies whether your gate hangs on an acreage entrance off Highway 51 or a ranch-house fence line in the 38053 ZIP. We stock heavy-duty hinges, post caps, roller assemblies, latches, and raw steel stock so we can fabricate and weld on site, not haul your gate to some distant shop.
Hinge Replacement
Most Millington ranch homes built in the 1960s through 1980s still hang on original gate hardware, and the humidity off the Wolf and Loosahatchie bottoms has done a number on it. We cut off corroded hinge barrels, prep the post face, and weld on new heavy-duty hinge sets rated for the gate’s actual weight. A hinge replacement on a standard ranch fence gate runs $180-$320 including hardware and welding. A sagging gate starts in the hinge post, not the middle, and that’s where we start.
Post Replacement
Gate post footings in Millington heave. The clay between the Wolf River and Loosahatchie River saturates through spring and shifts through a dry July, and a post set at 24 inches will re-lean within a season. We dig out the old footer, set a new post at 36-plus inches, add a drainage channel where the ground stays perpetually wet, and only then weld the hinges and operator mount back on. Full post replacement with new footing, drainage channel, and re-welding runs $350-$900 depending on post size, gate weight, and whether an automatic operator needs to be re-mounted.
Rail Repair
Slide gate rails are the forgotten part until an ice storm coats the track and the gate grinds to a halt. Millington gets hit with hard freezes every two to three years, and we end up cutting out bowed or snapped rail sections, realigning rack and pinion drives, and replacing roller carriages that froze solid. Rail repair and re-welding typically falls between $220-$600. On farm gates, we also repair top and mid rails that livestock leaned on one too many times.
Why does my gate post keep leaning in Millington’s Loosahatchie corridor?
Because the ground under it never dries out. Properties backing onto the Loosahatchie River corridor sit on saturated clay that swells every spring and shrinks every fall, and a post footing at shallow depth gets pushed progressively off plumb no matter how tight the original set was. The fix is a deeper footing, 36 inches or more, plus a drainage channel that pulls water away from the post. Call (877) 610-2993 and we’ll show you what’s under yours.
How do ice storms affect my slide gate track in Millington?
They coat the track in rough, rutted ice, the rollers skate instead of roll, and the gate either stalls halfway or overdrives past its limit stop and shears the rack bolts. Millington gets these storms every two to three years, and we see a spike of rack and pinion replacements and rail realignments afterward. The best prevention is a clean V-track, working roller guards, and a limit switch that was set properly in the first place.
Brands We Service in Millington
We carry parts and factory training for nine major brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Our trucks stock Linear and Viking boards, Ghost Controls arms, and DoorKing receivers so most Millington repair calls finish in one trip. If we don’t have it, we’ll tell you before we drive out, not after we’re standing in your driveway. See all brands we service.
Pricing for Gate Repair in Millington, TN
| Service | Typical range in Millington |
|---|---|
| Hinge & post repair | $240-$425 |
| Gate realignment | $185-$320 |
| Electric gate / control board retrofit | $310-$600 |
| Slide gate rack & pinion (ice storm) | $275-$450 |
| Single swing gate, manual | $2,800-$4,200 |
| Single swing gate, automated | $4,500-$6,800 |
| Double swing gate, automated | $5,800-$8,200 |
| Slide gate, automated with loops | $5,200-$9,500 |
| Capacitor / limit switch replacement | $95-$190 |
| Full slide motor replacement | $1,100-$1,900 |
| Keypad replacement | $110-$320 |
| Full post replacement with drainage | $350-$900 |
What pushes price up in Millington: post condition, gate weight, whether the operator is modern or obsolete, and whether the footing needs drainage work for clay-heavy, saturated soil. The price we quote at your gate is the price you pay, agreed in writing before any work starts. No trip charge inside the county, $40 off any repair over $200, and a permanent 10% discount for seniors and veterans.
Neighborhoods We Serve in Millington
We work every corner of Millington, from base-adjacent streets to rural acreage. Typical response time is same-day for most calls, usually within the hour when someone’s stuck waiting with a car that can’t get out.
- Wilkerson Crossing and Hunters Run off Navy Road
- Subdivisions along Shelby Drive and into 38054
- Rural parcels toward 38083 and the Tipton County line
- Properties backing onto the Loosahatchie River corridor
- HOA entry gates in newer 38054 communities
Service Area - Cities Near Millington
We coordinate dispatch from our Memphis office and run trucks to Millington, TN daily. We also serve Lakeland, TN, Bartlett, TN, Arlington, TN, Munford, TN, and Atoka, TN with the same crew, the same pricing, and the same 90-Day Done Right Promise. No trip charge inside the county.
Serving Millington, TN - Our Local Coverage Area
Gatewood Fence & Gate crews serve Millington and the communities around it; dispatch is coordinated from our Memphis office. The map shows the Millington coverage area; if your address is on it, we can help.
Also serving nearby: Millington, TN, Lakeland, TN, Bartlett, TN, Arlington, TN, Munford, TN, Atoka, TN.
FAQs About Gate Repair in Millington
Shelby County requires permits for new gate installations and electrical work, including power runs for operators. Simple repairs, hinge replacements, and welding on existing gates usually don’t trigger a permit. If your job needs one, we’ll tell you upfront and walk you through it. Call (877) 610-2993 for specifics on your project.
Yes. We service HOA entry gates in the 38054 subdivisions along Shelby Drive regularly, and we know the pressure HOAs face with minimal maintenance budgets. We quote in writing, meet with board members on request, and warranty the work to the association, not just one homeowner. The 90-Day Done Right Promise applies either way.
If your gate is in the 38053, 38054, 38055, or 38083 ZIP code, you’re in our area. We cover base-adjacent neighborhoods, rural acreage toward 38083, and everything in between. There’s no trip charge inside Shelby County. Call (877) 610-2993 and a live person will confirm coverage and schedule the truck.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Millington Customers Say
"Driveway gate had been dragging for two years and two other companies told me the whole thing needed replacing. Hal reset the posts, rehung it and it swings like it did when it went in. A fraction of the price of a new one."
- Hollis Amberly"He came out in the snow to get our gate closed after a delivery lorry clipped it, then came back in the spring to do the proper repair when the ground had thawed. Only charged for the second visit."
- Ingrid Solheim"The fence is excellent and it was fairly priced. He is not quick to answer email, so if you need him, ring. He always picks up the phone."
- Rodney Falkenrath