Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Lynwood
A dead gate opener or a sagging iron gate in Lynwood usually comes down to one of three things: a hinge post rotted at the base, an obsolete control board from the 1990s, or rust that started inside the tubing years before you ever saw it. Repair typically runs $180 to $340 for hinge and post work, and $275 to $600 when an operator needs a board or motor replacement. Most Lynwood jobs are finished the same day we show up. The gate stays in your driveway, we weld on site, and you know the price before we touch a single bolt. Call (877) 610-2993 and you’ll get a live person, not a voicemail.
Why Gatewood Fence & Gate Is Lynwood’s Preferred Gate Repair Company
The name on the shop is Hal Gatewood, and he’s been at this since 2001. Not passing through, not franchising, not running a dispatch queue three states away. When you call about a gate in Lynwood, Hal or one of his crew answers, and the person who answers is the person who shows up.
Lynwood’s gate stock is not like other cities’. A huge share of the ornamental iron gates in the 90262 ZIP went up between 1985 and 2005, and many of them were hung by local welders working without a license or a spec sheet. That means non-standard hinge spacing, hand-welded frames, and mix-and-match hardware you won’t find in a catalog. We have spent years adapting repairs to that reality, fabricating brackets and offsets on site rather than telling you the gate is scrap. Read the reviews from Lynwood homeowners and you’ll see the same thing repeated: the gate got fixed, the price matched the quote, and the person who did the work answers if something goes wrong. Every job carries our 90-Day Done Right Promise in writing.
Our Gate Repair Services in Lynwood
Electric Gate Repair
In Lynwood, most electric gate failures trace back to the operator, not the gate itself. Obsolete control boards in 1990s-era DoorKing and Linear operators are the big one. The board dies, the gate freezes mid-cycle, and you’re stuck parking on the street off Long Beach Boulevard. We stock replacement boards for current models and retrofit options for the older stuff, and we’ll tell you honestly when a new operator costs less than trying to revive a board that hasn’t been manufactured since the Clinton administration.
Automatic Gate Repair
Automatic gates are only as good as the safety edge and photocell behind them. A gate that reverses mid-cycle, creeps, or slams shut on a 90262 driveway usually has a failing sensor, a limit switch that wandered out of adjustment, or a gearbox grinding itself down. We service FAAC, BFT, Linear, Viking, LiftMaster, Ghost Controls, and DoorKing operators, and we test the full cycle, not just whether the arm moves. A gate that closes on its own is a gate failing, and we find where.
Hinge & Post Repair
This is the most Lynwood repair there is. The marine layer rolls in most nights, the I-710 puts particulates in the air, and a steel post sitting in a footing with no drainage rusts from the inside out. We see posts that look fine above the concrete and are paper-thin an inch below it. When that post shears, the gate drops. Not sags. Drops. We cut out the bad steel, pour a new footing, set a new post, and hang the gate straight. We also fix the hinge itself before the post gives way, which is the difference between a $200 repair and a $900 one.
Gate Realignment
The garage conversions that swept through Lynwood’s 1940s and 1950s housing stock changed a lot of driveways. A gate that matched the original opening now binds on one side, scrapes the concrete, or won’t latch because the geometry shifted under it. If the hinges and posts are still sound, realignment is the right fix and far cheaper than replacement. We re-hang, re-shim, and re-weld so the gate swings true across the corrected opening.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Lynwood
We service nine major gate brands, and we’re certified on all of them: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. For Lynwood homeowners, the practical part is that we carry common FAAC, BFT, and Linear parts in the truck, so most board and sensor swaps happen in one trip. No waiting a week for a control board to ship while your gate sits open. If it’s an older or oddball unit, we’ll fabricate or adapt what’s needed rather than condemning a gate that still has life in it.
Common Gate Repair Problems We See in Lynwood Homes
- Rusted posts at the footing. Nightly marine-layer moisture combined with I-710 particulate corrosion attacks the base of the post first. By the time you see flaking paint, the steel underneath is often compromised. If the gate is sagging and the hinges look tight, the post is the problem.
- Obsolete control boards on 1990s operators. The DoorKing and Linear boards from that era simply are not made anymore. When they die, you either retrofit a universal board or replace the operator. We’ll quote both and tell you which makes sense on your gate.
- Rust-through at hand-welded frame joints. Informal fabrication from the 1985-2005 wave often used thin tubing with no drainage holes. Water pools inside, rust eats outward, and the joint splits. We cut out the rot, weld in new steel, and add drainage so it doesn’t happen again.
- Missed safety retrofits. Many Lynwood gates predate modern safety standards, so there’s no photocell or reversing edge. That’s a liability on a shared walkway. We can add a safety photocell and edge to most older operators without replacing the whole unit.
Pricing for Gate Repair in Lynwood, CA
We Also Serve Cities Near Lynwood
If you’re in South Gate, East Rancho Dominguez, Willowbrook, or Paramount, the same crew that handles Gate Repair in Lynwood covers your street too. This is our home territory, and the drive is short. For more on what we do across the area, see Gate Repair in Lynwood for the full rundown.
Serving Lynwood, CA - Our Local Coverage Area
We’re based in the Lynwood area and know this community well - from Lynwood Gate Motor & Opener work to full rebuilds. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Lynwood
We reuse them whenever they’re structurally sound. Non-standard hinge spacing from a hand-fabricated gate doesn’t mean the hinges are bad. We measure the pin wear, check the barrel for play, and if the steel is still thick enough, we work around it, drawing on our Gate Parts & Welding in Lynwood to fabricate an offset bracket that matches the custom frame. We only cut off what’s actually failed. Call (877) 610-2993 and describe the gate; we’ll tell you what’s realistic before we come out.
If the rust is surface-level and the post still rings solid when struck, we can grind, treat, and reinforce it, no replacement needed. If the post has rotted through at the footing, replacing it now is far cheaper than waiting for the gate to drop onto the driveway. We cut out the bad section, pour a new footing, and set a new post, usually the same day. An inspection tells you which one you’re in. Estimates are free.
It depends on the board. If a direct replacement or a compatible universal retrofit exists, you’re looking at $275 to $500 for the board and labor. If the board is obsolete and no retrofit will talk to your existing motor, a full operator replacement is the cheaper long-term answer at $700 to $1,400 installed. We’ll show you the dead board and the quote before any work starts. Call (877) 610-2993 for an exact answer on your unit.
The moisture never really leaves. Lynwood sits close enough to the coast to collect overnight marine-layer condensation, and the I-710 corridor puts fine particulates on every horizontal surface. That’s why Gate Access Control in Lynwood needs hardware built for these conditions. Grit plus damp plus chipped paint equals rust that starts in days, not months. We treat the surface before repainting, and we add drainage holes where water was pooling inside the tubing, because rust starting from the inside won’t care how good your topcoat is.
Realignment is the right fix as long as the gate itself is structurally sound. The posts, hinges, and frame often outlive the driveway they were built for. We re-hang the gate to match the new opening, re-weld the hinge plates if needed, and set the latch so it actually catches. A new gate usually isn’t necessary. Call (877) 610-2993, and we’ll measure it for free.
Handling Lynwood’s Pre-2005 Ornamental Gates the Right Way
If there’s one thing that separates Lynwood from neighboring Downey or Compton, it’s density. In the 90262 ZIP, ornamental iron gates installed between 1985 and 2005 sit block after block, driveway after driveway. Those gates are now 20 to 35 years old, which is exactly when hinge fatigue, operator failure, and rust-through peak. Walk down a single street near Abbott Park and you might pass six homes whose gates are all aging on the same clock.
That’s why a national chain that assumes a modern, code-compliant install is the wrong call for most Lynwood gates. A lot of this iron was fabricated and hung by informal local welders, no license, no spec sheet, no drainage holes, no standard post dimensions. One job we did on a compact 1950s bungalow street near Abbott Park is a good example. The swing gate had been hung in the early 90s with non-standard hinge spacing and a hand-welded frame. The LiftMaster operator had a dead control board, and the hinge post was rusted through at the base. We cut out the bad post, poured a new footing, fabricated an offset hinge bracket to match the custom frame, and installed a fresh LiftMaster operator with a safety photocell. The gate cycles without sag correction now, but the fix required adapting to the gate, not forcing the gate to match a catalog.
That’s the kind of work Gate Repair in Lynwood actually requires. Not swapping parts that don’t match. Not quoting a $4,000 replacement on a gate that needs a $600 repair. Just honest steel work, done on site, with a 90-day written promise behind it.
Contact Gatewood Fence & Gate for Gate Repair in Lynwood
Call (877) 610-2993 and a live person answers, any hour, any day. Tell us what the gate is doing or not doing, and we’ll give you a straight answer about what it will take to fix it. Estimates are free. The price you agree to is the price you pay, and the 90-Day Done Right Promise means one call brings us back if anything isn’t right. Hal Gatewood’s name is on the shop and on every invoice. You can look us up, look us over, and hold us to it.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Lynwood since 2001.