Gate Repair in Everett - Same-Day Repair, Priced Before We Start

Gate Repair in Everett, MA

Gate repair in Everett usually costs between $180 and $650, depending on whether we’re cutting out rusted hinge pins, replacing a corroded operator board, or resetting a post that five winters of freeze-thaw pushed out of plumb. Most repair calls in 02149 get same-day or next-day service, because a gate that won’t close on a shared triple-decker fence line is a security problem, not a weekend project. Call (877) 610-2993 and a live person answers. We’ll tell you straight what’s wrong, what it costs, and when we can be there.

Call (877) 610-2993

Key takeaways:

• Most Everett gate repairs run $180 to $650, quoted in writing before work starts
• Salt air from the Mystic River and Chelsea Creek corrodes iron hardware faster than inland towns
• Original wrought-iron gates on homes built 1890-1930 are almost always worth repairing, not replacing
• Every repair carries the 90-Day Done Right Promise in writing

Why Everett Homes Are Different

Everett’s residential streets are packed tight with triple-deckers and two-families built between roughly 1890 and 1930, and a lot of those homes still have their original wrought-iron side-yard gates. Those gates squeeze into passages with 18 to 24 inches of swing clearance, which means every half-inch of sag scrapes pavement. You don’t yank those gates out and start over. You repair them in place, because replacing one almost always means arguing with a neighbor about who owns the fence line the gate straddles.

Then there’s the water. Everett sits along the Mystic River and Chelsea Creek, and that tidal salt air settles into every hinge barrel, latch plate, and weld bead. Freeze-thaw cycles heave concrete-set posts out of plumb every winter, and the salt accelerates corrosion on whatever steel is exposed. Hardware that might last 20 years in Worcester shows structural rust failure here in under a decade. On blocks off Broadway and over by Ferry Street, a single gate often serves two separately owned buildings, which means the repair itself is only half the job.

Gate Repair in Everett

Most gate repair in Everett comes down to three local realities: rusted-solid hinge pins on century-old iron gates, concrete footings that frost has heaved out of plumb, and operator boards fighting salt air from the Mystic River. We fix all three in your driveway, not in a shop across town. We weld on site, we replace only what’s actually failed, and every price is written down before we touch a screw. For a full look at how we handle these jobs, see our Gate Repair page.

Hinge & Post Repair

This is the bread-and-butter of gate work in Everett. The original iron gates on homes built between 1890 and 1930 were built well, but the galvanized coating wore through decades ago. What’s left is pitted steel that rusts from the inside out. We regularly find hinge posts frozen solid where they enter the concrete footing, with the steel pins snapped from freeze-thaw heave. Hinge and post repair on a single gate in Everett typically runs $220 to $480, depending on how far the corrosion has traveled and whether we need to sleeve the post before re-hanging the gate. Fix the panel without the post and you’ll fix it twice.

Gate Realignment

A sagging gate in Everett is almost never the gate’s fault. It’s a hinge post that shifted, a footing that heaved, or a top rail that’s been weeping rust for a decade. On narrow side yards off Broadway, where swing clearance is 18 to 24 inches, even a half-inch of sag makes the gate scrape concrete every time it opens. Gate realignment runs $180 to $350 in Everett, which includes checking the post with a laser level and resetting it if it’s moved. Most realignments finish inside a few hours.

Electric Gate Repair

Electric gate failures near Chelsea Creek usually start at the terminal block. Salt-laden air works into the control housing and corrodes the connections until the gate resets intermittently or ignores the remote altogether. Electric opener and board repair in Everett runs $260 to $650, depending on whether we’re re-seating terminals or replacing a board that’s too far gone. We test the receiver, the safety edges, and the power run before we swap a single part, so you’re not paying for parts you didn’t need.

How much does gate repair cost in Everett?

Most gate repairs in Everett land between $180 and $650. Hinge and post work runs $220 to $480, realignment $180 to $350, weld and rust repair $200 to $520, and electric opener or board repair $260 to $650. The biggest cost driver is rust: frozen hinge pins that need cutting out add labor. Call (877) 610-2993 for an exact quote. Estimates are free.

Can you repair my original wrought-iron gate without replacing it?

Almost always, yes. We weld on site in your driveway, so the gate stays where it is. We cut out the corroded sections, weld in new steel, grind it smooth, and re-coat. The only time we recommend replacement is when the structural frame has rusted through in multiple load-bearing places and welding would leave the gate weaker than it started. Even then, we’ll show you the damage before you decide. Call (877) 610-2993 to schedule a look.

Gate Installation in Everett

Gate installation in Everett almost always comes down to the same three realities: a tight side yard, a shared fence line, and salt air off the Mystic River eating at whatever gets bolted down. We build gates that hold plumb through a New England winter and still open clean in July. If you’re in 02149 and need a driveway gate, pedestrian gate, or security gate put in, we measure first, quote second, and dig third. Our full Gate Installation page covers the process in detail.

Pedestrian Gate Installation

This is the work we do most on Everett’s dense residential streets. The classic setup is a century-old wrought-iron side-yard gate in a passage off Broadway, with maybe 18 to 24 inches of actual swing room. We install pedestrian gates that fit that space and operators that work within it. A pedestrian gate with an operator for keypad or remote entry typically runs $1,400 to $3,200 in Everett, depending on whether we need to rebuild the hinge post and pour a new footing. We do the welding on site, so your existing fence line stays intact.

Sliding Gate Installation

When a swing gate won’t fit, a sliding gate is usually the answer. Sliding gates are common in Everett’s rear alleys and along shared driveways where two families need access and there’s no room for a gate to arc outward. A sliding gate installation in Everett runs $2,200 to $5,500 with operator, with the high end covering longer cantilever spans for double-width drives. We build for salt air and freeze-thaw cycles, because a slide gate that seizes in late January is a problem you shouldn’t have to call about twice.

Driveway Gate Installation

Driveway gates in Everett are a game of inches. The lots are narrow, the driveways often shared, and there’s rarely room for a big ornamental swing. We measure the actual setback, check the grade, and build accordingly. Most driveway gate installations in Everett land between $1,800 and $4,200 for gate and posts. A properly installed driveway gate starts with the post footing, not the gate panel. Set the post deep enough to survive frost heave and the gate will swing true for years.

Can you install an automatic sliding gate on a shared driveway in Everett without closing off access for the other owner?

Yes. We stage shared driveway sliding gate installations so pedestrian and vehicle access stays open the entire time. The gate gets built and mounted in sections, and we coordinate with both owners on timing. Before any work begins, we establish who authorizes the work and how the cost is split. Call (877) 610-2993 and we’ll walk you through it.

My side yard off Broadway only has about 22 inches of swing clearance. What kind of operator can you install?

We’d install a swing gate operator mounted on the hinge post side, usually a Linear or Ghost Controls arm that works within tight clearances. In some cases we build a new steel hinge post with the operator concealed behind it so the gate swings through the same tight arc. We’ve done this exact job with 20 inches of clearance and kept the shared walkway open the whole time. Call (877) 610-2993 for a written quote.

Gate Motor & Opener in Everett

Gate motor and opener service in Everett means working around triple-deckers, shared side-yard gates, and salt air that shortens the life of anything electronic. We get your gate opening and closing again, usually same day, without selling you a new operator you don’t need. If your opener is dead, grinding, or stuck mid-track, call (877) 610-2993 and a live person answers. Our Gate Motor & Opener page breaks down every repair and install we do.

Motor Repair

Most Everett gate motor failures are either salt-corroded internals or snapped drive components. We replace the worn part, not the whole operator, when the rest of the unit has life left. A gate motor repair in Everett typically runs $220 to $480 depending on what failed. Replacing a stripped rack section or a corroded limit switch lands on the lower end; a full control board replacement runs $350 to $600. If your motor hums but won’t move, we trace it back to the actual fault instead of quoting you a new system on the spot.

Slide Motor Installation

For Everett’s zero-clearance lots, a slide conversion is often the only way to automate a gate. When a swing gate won’t open because a triple-decker wall sits six inches from the hinge post, we mount a compact slide motor on a custom steel post footing, run the rack, and wire the safety edges and loop detector. New slide motor installations with a conversion run $1,600 to $4,500, depending on whether we’re pouring new post footings and running conduit. The gate stays in your driveway while we weld and fit.

Battery Backup

Coastal storms knock out power in Everett often enough that a gate without battery backup becomes a real access problem. We install sealed battery backup systems on most major gate operator brands, including slide and swing units, so the gate keeps running when the power drops. Battery backup install adds $400 to $800 depending on the operator and the run. We’ll size it to your specific unit and put the whole install on the same written quote.

How do I know if my gate motor needs a new loop detector or a whole new operator?

If the gate opens on the keypad or remote but ignores a vehicle sitting on the drive, the loop detector is usually the problem, not the motor. We test the loop’s capacitance and the wire continuity before condemning any operator. A bad loop often costs under $300 to diagnose and replace, while a full operator swap would run four to ten times that. Call (877) 610-2993 and we’ll diagnose it honestly.

Can you add battery backup to my gate operator so it still works during coastal storms?

Yes. We install sealed battery backup systems on most major brands, so the gate keeps running when the power drops. For Everett’s coastal storm pattern, a battery covering 20 to 50 cycles gets you through the outage without leaving vehicles trapped in the drive. We’ll size it to your operator and put it on the same written quote as the install. Call (877) 610-2993 for a price.

Gate Access Control in Everett

Gate access control in Everett usually comes down to one of a few jobs: a keypad that stopped accepting codes, a remote that quit on one side of the house, or a phone entry system at a triple-decker that buzzed once and never buzzed again. We fix all of it, most of it same day. If you’re anywhere in 02149 or on the streets off Broadway, Ferry Street, or Main Street, you’re a short drive from a real person who does this work every week. See our Gate Access Control page for the full range.

Keypad Entry

A keypad entry system in Everett has to survive wet winters and salt-laden air from Chelsea Creek. We install new keypads, replace worn membrane pads, and rewire units where corrosion has eaten the terminals. Most residential keypad jobs in Everett run $225 to $475 installed, depending on whether we’re swapping an existing unit or running new wire to the operator. On triple-deckers where the keypad sits in a shared alley, we weatherproof the housing and use stainless fixings so you don’t get the same failure in three years.

Phone Entry

Phone entry systems are common on Everett’s rental two-families and triple-deckers. The problem is rarely the phone line itself. It’s usually a corroded relay or a power supply that’s been wet and quit. A phone entry repair in Everett typically lands between $250 and $600. If you’re replacing an old unit outright, figure $900 to $1,400 for a quality system installed, not counting any gate operator work. We test the whole path from call box to door strike and replace only what’s actually failed.

Card Reader

Card readers aren’t just for commercial lots. We do them for two-families where each unit wants its own credential, and for small condo associations around Broadway and Glendale Park that need an audit trail. A single-door card reader system in Everett generally runs $700 to $1,600 installed, depending on the panel and whether we’re coordinating with an existing gate operator. We set up the cards, program the access levels, and walk you through it before we leave.

What’s the best access control for an alley gate in Everett with only 20 inches of swing clearance?

A surface-mount keypad with a compact operator works best in tight clearances. You need a system that reads the code fast and doesn’t swing the gate wide into the alley. We usually recommend a keypad with a small gear-driven arm operator, with stainless fixings to survive the salt air. Call (877) 610-2993 for a number before we quote it in writing.

Why does my Everett gate hinge seize up even though it’s only six years old?

Salt air from the Mystic River and Chelsea Creek accelerates rust on ferrous hinge hardware. We see hinge pins and posts in Everett fail in six to eight years, where the same hardware lasts fifteen-plus in Malden. The fix is stainless steel pins and bushings, plus freeing the seized joint before it snaps. Call (877) 610-2993 for a quote. Estimates are free.

Gate Parts & Welding in Everett

If your gate in Everett is sagging, dragging, or won’t latch, the fix usually comes down to worn or broken parts that need replacing or welding, not an entire gate that needs scrapping. Most of the gates we work on in 02149 are original wrought-iron pieces from the early 1900s, and they’re worth saving. We come to your driveway in Everett, weld on site, and leave the gate working better than it has in years. Our Gate Parts & Welding page covers what we stock and what we fabricate.

Hinge Replacement

On century-old gates in 02149, the hinges are frequently the first thing to fail. Salt air from Chelsea Creek and the Mystic River works its way into the barrel and pins, and before long the gate is dragging on the latch side. We cut off the old hinges, weld on new ones sized for the gate’s weight and swing, and set the gate so it closes square. A typical hinge replacement in Everett runs $180 to $420, depending on whether it’s one hinge or the full set.

Post Replacement

New England frost moves Everett’s fence posts every winter. When the concrete holding the post is cracked, the post leans, and the gate follows. We dig out the old footing, set a new post in proper concrete, and weld the gate’s hinge tabs back to plumb. Post replacement in Everett typically ranges from $350 to $750 per post, depending on depth, access, and whether we’re also resetting the gate frame. On narrow side yards where the post sits six inches from a neighbor’s foundation, we hand-dig and set it carefully.

Custom Welding

Some gates weren’t mass-produced, and neither are our fixes. We fabricate missing finials, rebuild latch strikes, weld broken scrollwork back into place, and reshape twisted stiles until they line up again. Hal welds on site, meaning your gate stays in your yard and you watch the work happen. Custom welding rates in Everett run $95 to $150 per hour plus materials, with most small jobs finishing in two to three hours.

Is gate welding in Everett more expensive than in nearby cities?

No, our rates for Everett are the same as Malden, Chelsea, Revere, and Medford. The difference in Everett is often the working conditions: tight alley access and shared fence lines can add time, which we factor into the quote up front. You’ll know the full price before we strike an arc. Call (877) 610-2993 for a written estimate.

What warranty do you offer on gate parts and welding in Everett?

Every job we do in Everett carries our 90-Day Done Right Promise, in writing. If a weld cracks or a hinge we installed fails within 90 days, we come back and make it right at no charge. Hal’s name is on the shop and on every invoice, and he doesn’t hide from either. Call (877) 610-2993 if something isn’t right.

Brands We Service in Everett

We service DoorKing, Linear, and Ghost Controls operators on Everett gates every month, including rack-and-pinion slide units that see heavy salt exposure near Chelsea Creek. Parts for common models are stocked locally, so most motor and board replacements happen same week, not same month. See our brands for a full rundown of what we repair.

Pricing for Gate Repair in Everett, MA

Neighborhoods We Serve in Everett

We work throughout Everett, from the triple-deckers near Broadway up to the streets around Ferry Street and Main Street, over by Everett Square and the residential blocks near Hancock Street. Most repair calls get a same-day or next-day visit, depending on when you call. Emergency calls get answered around the clock.

• Broadway corridor
• Everett Square
• Ferry Street / Main Street area
• Hancock Street corridor
• Rivergreen / Lower Broadway

Service Area - Cities Near Everett

Our crew covers Everett, MA and the surrounding cities. If you’re in Everett, MA, Malden, MA, Chelsea, MA, Revere, MA, Medford, MA, or Somerville, MA, the same live-person phone line and the same 90-Day Done Right Promise apply. Dispatch is coordinated from our Boston office; crews serve Everett locally every week.

FAQs About Gate Repair in Everett