Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Eagle Mountain, TX
Gate repair in Eagle Mountain typically costs $220 to $680 depending on whether you need a hinge re-weld, post re-plumb, or opener board replacement, and most repair calls in the 76179 ZIP get same-day or next-morning response. We’re Gatewood Fence & Gate, and we work Eagle Mountain every week, from the estate lots off Ten Mile Bridge Road to the rural parcels toward Briar. The black clay soil out here moves gates out of plumb faster than almost anywhere in Tarrant County, which is why we fix the post, not just the panel. Call (877) 610-2993 and a live person answers, day or night.
Why Eagle Mountain Homes Are Different
Eagle Mountain isn’t a typical Fort Worth suburb. It’s a lake-community enclave on Eagle Mountain Lake with an unusually high concentration of large-lot, long-driveway properties, many with private estate-style gates. The custom and semi-custom homes built from the mid-2000s onward came with ornamental iron swing gates or tube-steel automatic slide gates as standard features. On the rural fringe, older parcels still carry ranch-style pipe gates on agricultural fencing.
What unites all of it is the soil. The 76179 ZIP sits on expansive black clay that heaves when wet and contracts when dry, and that cycle never stops. We’ve found gates two to three inches out of plumb within two or three seasons of installation, especially along lake-access roads and cove-side driveways where posts sit on caliche-topped pads over shifting clay subgrade. Summer heat regularly exceeds 100°F here, baking opener electronics, while sustained wind off the lake loads gate panels harder than inland properties expect. The occasional hard ice event snaps actuator arms and freezes solenoid locks. This place tests gates harder than most.
Gate Repair in Eagle Mountain
Most gate repair calls we get in Eagle Mountain start the same way: the gate drags, binds, or the opener trips and the homeowner assumes the motor is shot. Usually it’s the post. The black clay under your driveway has shifted the hinge post out of plumb, and everything after that is symptoms. We diagnose on-site, quote a written price before any tool comes out, and fix it in your driveway rather than hauling anything off. Our Gate Repair crew handles everything from hinge re-welds to full realignment, and every job carries the 90-Day Done Right Promise in writing.
Electric Gate Repair
An electric gate that opens halfway, hums without moving, or quits after a storm usually has a bad circuit board, a failing actuator arm, or a photocell that’s been cooked by the Texas sun. We service FAAC, BFT, Linear, and Viking openers, and we carry the parts your system actually needs rather than guessing. In Eagle Mountain, UV damage to opener internals is a regular sight by August; we’ve replaced swollen capacitors and cracked solder joints on Viking and FAAC boards every summer for years. Opener board replacement on a FAAC or Linear system typically runs $260 to $520 including the part, and we quote that number before we start.
Hinge & Post Repair
Here’s the local pattern we see constantly: a gate post that looked fine at build-out is now two or three inches out of plumb. That’s the black clay soil doing what it does. When the post moves, the hinges bind, the gate drags, and the opener burns itself out trying to compensate. In Eagle Mountain, a hinge fix without a post check is fixing it twice. We re-plumb the post, reset it in compacted base below the active clay zone, and re-hang the panel. A hinge and post re-plumb on a standard ornamental swing gate runs $375 to $680, depending on post depth and concrete condition.
Gate Realignment
A gate that catches the latch, scrapes the drive, or won’t sit flush against the stop post is a realignment job, and Eagle Mountain gives us these constantly. Long driveways on sloping lots add extra stress to the frame, so what starts as a dragging corner becomes a bent hinge pin within a season or two. We true the panel, re-hang it, and verify the opener’s travel limits afterward so it doesn’t eat itself again. A full realignment job with re-hang and travel-limit reset is generally $220 to $410. When the existing posts are too far gone, we’ll tell you straight.
How fast can you get to my gate in Eagle Mountain?
Most repair calls in Eagle Mountain get a same-day response when you call before early afternoon, and around the clock for emergency lock failures or gates that won’t close and secure the property. Call (877) 610-2993 and you’ll talk to a live person, not a voicemail tree.
Why does my gate keep sagging after someone already fixed it?
They probably fixed the panel without fixing the post. The black clay under 76179 shifts posts out of plumb every wet-dry cycle, and a hinge replacement on a leaning post just buys you a season. We re-plumb the post first, then re-hang the gate. That’s the difference between a repair that holds and one that doesn’t.
Gate Installation in Eagle Mountain
Gate installation in Eagle Mountain runs $1,800 to $6,500 for most residential driveway gates, with automated sliding systems at the higher end and manual swing gates at the lower. We build and set gates that stay square on the black clay, which is the whole ballgame out here. You call (877) 610-2993, you get a real person, and you get a straight answer about what it costs before any work starts. Our Gate Installation covers everything from ornamental walk gates to full estate automation.
Driveway Gate Installation
Most driveways in Eagle Mountain are longer than what you’d see in Fort Worth proper. Big lots mean big gate openings, twelve to sixteen feet wide is common, and that means heavier panels and stronger opener requirements. We measure for grade slope, hinge rating, and wind load before we quote, because a gate on an open lakeside sweep catches a lot more wind than one tucked up against a house. A single swing driveway gate in tube steel typically lands between $2,000 and $3,500 installed with proper post footers.
Sliding Gate Installation
Sliding gates are the right call when a driveway slopes toward the road or when a swing gate would have to sweep across a flower bed, and Eagle Mountain has plenty of both. We check cantilever weight rating against the panel material and wheel placement before anything gets welded. A slide gate that drags in year two means the track was sized wrong or the concrete pad shifted, and we don’t let that happen. A double swing or sliding gate with an operator is $4,800 to $6,500 depending on panel material, opener duty rating, and whether we’re adding keypad or card access.
Pedestrian Gate Installation
You see a lot of these on the custom-home estates east of the lake, usually an ornamental iron walk gate matched to the driveway gate. We set the post deep enough to get below the clay line and we anchor with a header bridge when the opening is in decorative brick, which it often is out here. A manual ornamental iron walk gate runs $1,800 to $2,800 installed with a proper concrete post footer.
What does a full gate installation include?
A full installation includes removing the old gate if there is one, digging for posts, setting posts in concrete below the clay active zone, hanging and aligning the new gate, installing and programming the opener if automated, and walking through operation with you before we leave. If you’re adding access controls, we integrate them into the same installation so you’re not coordinating multiple contractors.
How much does a gate installation cost in Eagle Mountain compared to nearby cities?
Expect to pay roughly $1,800 to $6,500 in Eagle Mountain depending on gate type and automation. The range is comparable to Saginaw and Azle, with slightly more on the high end for lakeside properties that need deeper post work and higher-duty openers for wind and slope. County-wide, our no-trip-charge policy keeps the drive from adding cost.
Gate Motor & Opener in Eagle Mountain
Gate motor and opener problems in Eagle Mountain rarely start with the motor. Around the 76179 ZIP, the expansive black clay soil under long lake-community driveways heaves and contracts with every wet-dry cycle, shifting gate posts out of plumb and racking the operator until it binds, trips, or strips a gear. That’s the call we make most often out here. If your gate whines, jerks, or won’t close square, call (877) 610-2993 and a live person answers, day or night. Our Gate Motor & Opener service covers repair, replacement, and new installation on nine major brands.
Motor Repair
Most gate motor repairs in Eagle Mountain start with us checking post plumb and panel weight before we ever touch the motor. A FAAC swing operator that keeps tripping after a rain usually isn’t broken, it’s binding against a post the clay moved two inches. We re-plumb the post, rack the hinges straight, and only then address the motor, gears, or control board. Repair-first means we replace worn parts, not whole systems. Gate motor repair typically runs $180 to $420 for common fixes like limit switch adjustment, gear replacement, or control board troubleshooting.
Motor Installation
Installing a gate motor in Eagle Mountain is not a bolt-on job. The soil under the post decides whether the motor survives. We set or reset posts below the caliche cap where we need to, then install the operator so the arm travels clean and the entrapment sensor has a real fighting chance. New installs on acreage gates get a measured, written price before any work starts, with no trip charge inside the county. A full swing arm operator replacement runs $950 to $2,200 depending on gate weight, post condition, and whether we need to reset a post the clay has moved.
Slide Motor Service
Slide motors on Eagle Mountain acreage gates face a double threat: wind off Eagle Mountain Lake and dust off the ranch roads. The combination wears pinion gears and fills guide tracks with grit faster than an equivalent gate in town. We service the full slide assembly, motor, chain, rack, roller trucks, and safety edges, and we check the track level, because a slide gate that fights a low rail is a slide gate that’s already half-broken. Slide motor replacement runs $1,100 to $2,800, with the higher end covering wide estate gates with rack, chain, and safety edge work.
Why does my Eagle Mountain swing gate operator keep tripping after the first big rain?
Rain soaking into the black clay under your gate post makes it heave, pushing the post out of plumb and binding the operator. The FAAC or BFT arm then trips its entrapment sensor because it’s working too hard against a misaligned hinge. We re-plumb the post, set a deeper footing where the caliche allows, and only then reset the motor limits.
My slide gate motor whines but the gate barely moves after a lakeside windstorm - what broke?
That’s a stripped rack and pinion gear or a chain that’s stretched and jumping teeth. The wind off Eagle Mountain Lake flexes the wide panel until a gear takes the strain and fails. We replace the gear, check the full track for rail damage, and often add or reset guide stops so the panel doesn’t flex as far in the next blow. Repairs start around $180.
Gate Access Control in Eagle Mountain
Access control in Eagle Mountain means keypad entry, card readers, intercoms, and remote systems for estate properties where the driveway might be two hundred yards from the house. We install and repair these systems to integrate cleanly with your gate motor, not as an afterthought that fights the opener for voltage. Our Gate Access Control service covers everything from standalone keypads to phone-app-enabled entry systems on multi-acre lake properties.
Keypad & Intercom Systems
On the large lots around Eagle Mountain Lake, an intercom at the gate isn’t a luxury, it’s how you know who’s there before they reach your door. We wire for both power and data at the gate post, using conduit rated for the UV and moisture exposure this lakeside climate delivers. A basic keypad entry system with installation typically runs $400 to $850, while a full intercom with video feed and remote release lands between $1,200 and $2,400 depending on cable run length and whether we need to trench under a long driveway.
Remote & Smart Access
Remote systems on Eagle Mountain estates need range. We spec transmitters and receivers for the actual distance from gate to house, not the default suburban rating, and we account for the metal gate panel itself blocking signal if the receiver placement isn’t thought through. Smart-phone-enabled access is available on most modern operators we install, and we configure it so the app talks to the opener directly, not through a cloud server that quits when your rural internet hiccups.
Do I need separate power run to the gate for access control?
Usually, yes. Most access devices need their own low-voltage power run from the house or a dedicated transformer at the gate. We handle that wiring as part of the installation, including trenching and conduit, so you’re not hiring a second contractor. The cost is built into the quote we give you before work starts.
Can you add access control to my existing gate in Eagle Mountain?
Yes, provided the gate and opener are in good working order. We audit the existing system first, because adding a keypad to a gate that already binds or drags is putting lipstick on a pig. If the mechanics are sound, we can add keypad, card reader, or intercom and integrate it with your current FAAC, Linear, or Viking operator.
Gate Parts & Welding in Eagle Mountain
If your gate hinge has torn loose or a post has started leaning toward the driveway, you’re not imagining it. The black clay under Eagle Mountain’s 76179 lots swells and shrinks through every wet-dry cycle, and over two or three seasons that movement quietly racks even a well-built gate out of square. We’ve been welding and repairing gates on this side of the lake long enough to know the failure starts in the post, not the panel. Our Gate Parts & Welding service keeps your gate in your driveway, not on a trailer headed to some shop.
Hinge Replacement
Around the lake-access roads and cove-side driveways of Eagle Mountain, hinge failures almost always start at the post. A hinge that’s torn free from a post set in shifting clay tells you the post has moved. We cut the old weld, re-plumb the post, and set the new hinge so the gate hangs true. Hinge replacement with post re-plumb typically runs $180 to $340 per hinge, depending on the post and gate weight.
Post Replacement
A gate sags in the hinge post, not in the middle. That’s where we start. On Eagle Mountain’s half-acre and multi-acre lots, posts often sit in caliche-topped pads over expanding clay, and we regularly find gates two or three inches out of plumb inside a few years of installation. We’ll cut the post below grade, set a new one properly, and weld the hardware back on, all while the gate stays in your driveway. Full post replacement runs $450 to $900 for most residential driveway gates, including digging, setting, welding, and re-hanging.
Rail Repair & Custom Welding
Tube-steel slide gates and ornamental iron swing gates across Eagle Mountain take real abuse from wind coming off Eagle Mountain Lake. When a top or bottom rail cracks, the gate starts dragging and the motor works harder than it should. We weld the rail, reinforce the joint where the original fabricator undersized it, and make sure the gate rolls or swings free before we leave. Rail repair runs $150 to $400, and custom welding and fabrication starts at $120, quoted by the job.
Can you handle emergency welding on a gate that won’t open?
If the gate is stuck shut and you can’t get a vehicle in or out, we address it as an emergency. We’ll walk through what’s wrong over the phone, give you a number for the fix, and get there as quickly as the schedule allows. A cracked weld on a slide gate rail is usually repairable on site in one visit.
Is gate welding more expensive in Eagle Mountain than nearby cities?
Pricing is the same across Eagle Mountain, Saginaw, Azle, Briar, and River Oaks. What changes the number is the gate itself: a heavy ornamental swing gate on a lakefront lot costs more to re-hang than a light tube-steel gate because of the time and material involved. You’ll know the exact number before any work starts.
Brands We Service in Eagle Mountain
We carry parts and factory training for nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. For Eagle Mountain’s mix of estate automation and ranch-grade hardware, we stock FAAC, BFT, Linear, and Viking parts locally, which means most repairs don’t wait on shipping. If your operator is one of these brands, we can diagnose and usually fix it in one visit. See our brands for full details.
Pricing for Gate Repair in Eagle Mountain, TX
| Service | Typical range in Eagle Mountain |
|---|---|
| Hinge replacement with post re-plumb | $180 - $340 per hinge |
| Full post replacement (dig, set, weld, re-hang) | $450 - $900 |
| Gate realignment with re-hang & limit reset | $220 - $410 |
| Broken weld repair on steel frame | $140 - $300 |
| Hinge & post re-plumb (ornamental swing gate) | $375 - $680 |
| Opener circuit board replacement (FAAC/Linear) | $260 - $520 |
| Gate motor repair (limit, gear, board) | $180 - $420 |
| Swing arm operator replacement | $950 - $2,200 |
| Slide motor replacement | $1,100 - $2,800 |
| Manual ornamental walk gate (installed) | $1,800 - $2,800 |
| Single swing driveway gate (tube steel, installed) | $2,000 - $3,500 |
| Double swing or sliding gate with operator (installed) | $4,800 - $6,500 |
What pushes price up in Eagle Mountain is almost always the soil work: posts that need deeper footings to get below the active clay zone, or reset after the black clay has heaved them out of plumb. Wind exposure on lakeside properties can also mean heavier-duty hardware. The price we quote is the price you pay. We don’t show up and hand you a bigger number than the one you agreed to.
Neighborhoods We Serve in Eagle Mountain
We work throughout the Eagle Mountain area, from the large-lot estates near the lake’s eastern shore to the rural-tinged parcels north toward Briar. Typical response time for a repair call in Eagle Mountain is same-day or next morning.
- Lake Country Estates
- Eagle Mountain Estates
- Ten Mile Bridge Road corridor
- Boat Club Road area
- Rural parcels along Peden Road
Service Area - Cities Near Eagle Mountain
We schedule Eagle Mountain alongside our routes through the western Tarrant County lake communities. If you’re in Eagle Mountain, TX, Saginaw, TX, Azle, TX, Briar, TX, River Oaks, TX, or Keller, TX, you’re in our regular service area with no trip charge inside the county. Scheduling is coordinated from our Dallas-Fort Worth office, and crews serve each city locally.
Serving Eagle Mountain, TX - Our Local Coverage Area
Gatewood Fence & Gate crews serve Eagle Mountain and the communities around it; dispatch is coordinated from our Dallas-Fort Worth office. The map shows the Eagle Mountain coverage area; if your address is on it, we can help.
Also serving nearby: Eagle Mountain, TX, Saginaw, TX, Azle, TX, Briar, TX, River Oaks, TX, Keller, TX.
FAQs About Gate Repair in Eagle Mountain
Most residential gate repairs don’t require a permit in the 76179 area, but new installations or structural changes to the fence line sometimes do, depending on your HOA or the city’s current requirements. We can tell you what we’ve seen on recent jobs in your specific neighborhood, and we’ll flag it during the estimate if a permit looks likely.
For a gate that won’t close and leaves your property unsecured, we treat it as an emergency. Call (877) 610-2993 any hour and a live person will answer. We’ll get someone there to secure the opening, even if that means chaining and bracing the panel until the proper repair can be done.
Yes. Hal’s crew covers the whole 76179 area, from the lake-access roads and cove-side driveways down to the rural fringe where the parcels turn into pasture. That includes the custom homes built from the mid-2000s onward and the older ranch properties that still have manual pipe gates.
Call (877) 610-2993 for a free estimate on any gate repair, installation, or welding job in Eagle Mountain. A live person answers around the clock, and we’ll give you a written price before any work starts. Seniors and veterans receive a standing 10% discount, and we offer $40 off any repair over $200.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Eagle Mountain Customers Say
"Operator had died and the manufacturer no longer makes the board. Rather than sell me a whole new system he found a compatible unit and adapted the mount. Saved me a great deal of money."
- Salvador Arredondo"Hundred and forty feet of cedar privacy fence, all posts set in concrete, all of it dead level on ground that is anything but. He walked the line with me twice before a single hole was dug."
- Judith Stallworth"Driveway gate had been dragging for two years and two other companies told me the whole thing needed replacing. Hal reset the posts, rehung it and it swings like it did when it went in. A fraction of the price of a new one."
- Hollis Amberly