Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Denver
Gate repair in Denver comes down to knowing the soil, the alleys, and the old iron. We reset alley-gate hinge posts in Baker and Curtis Park that have heaved 5 to 10 degrees out of plumb after every freeze-thaw winter. We weld cracked vintage wrought iron in Capitol Hill without yanking the gate off its hinges. If your gate is sagging onto the concrete pad, grinding its latch, or an opener just quit, call us at (877) 610-2993 and a live person picks up. Not a voicemail, not a call center. Hal Gatewood has owned this shop since 2001, and the address is published. You can drive to the shop and look him in the eye.
Why Gatewood Fence & Gate Is Denver’s Preferred Gate Repair Company
We’re not a franchise that dispatches a rotating cast of techs from three counties away. Hal Gatewood’s name is on the shop and on every invoice. When a Denver homeowner calls about a gate that won’t close, the person who shows up is accountable to the person whose name is on the job. Every repair carries the 90-Day Done Right Promise in writing. If it’s not done right, we make it right. One call brings Hal back. No runaround, no “that was a different crew.”
Denver customers call us because the work is repair-first. A gate sags in the hinge post, not in the middle, and that’s where we start. We weld on site, in your driveway or alley, rather than hauling the gate off and swapping parts that don’t need swapping. Show me the gate closing on its own and I’ll show you where it’s failing. That’s the standard.
We answer the phone 24 hours a day, seven days a week. Not a voicemail, not a chatbot. Our Denver office coordinates service across the central ZIP codes: 80203, 80204, 80205, 80206, plus Glendale, Edgewater, Lakewood, and Wheat Ridge. Standing offers apply on every Denver job: $40 off any repair over $200, no trip charge inside the county, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans. You’ll know the price before we start, and we don’t change it at the door.
Our Gate Repair Services in Denver
Central Denver’s housing stock is a specific breed: late-Victorian Denver Squares, Craftsman bungalows, and brick row houses built between roughly 1890 and 1940. Most sit on alley-accessed lots with original or early-generation wrought-iron or wood gates. Repairing those gates is not a parts-swap job. It’s a measurement, fabrication, and realignment job. Here’s what we handle most often in Denver.
Electric Gate Repair
Electric gate repair in Denver typically means a gate operator that quit, a keypad that won’t take the code, or a safety edge that’s sending false trip signals. In neighborhoods like Cheesman Park and Capitol Hill, we see older operators with failing control boards and limit switches corroded by seasons of freeze-thaw condensation. We service Linear, Viking, Ghost Controls, and DoorKing among others, and we stock common parts locally so we’re not waiting on a week-long shipment.
Automatic Gate Repair
Automatic gate repair in Denver’s alley-grid blocks has a particular failure mode: the 50°F daily temperature swings loosen operator fasteners and stress welds on slide gates, leading to rack and pinion misalignment where the gate jumps the track. We realign racks, re-torque operator mounts, and replace worn pinion gears. UL 325 compliance matters here. Alley-facing gates on shared rights of way often lack modern entrapment protection; a working photo-eye or edge sensor is not optional. If your gate reverses unexpectedly, call us before someone gets hurt.
Hinge & Post Repair
Denver’s clay-heavy soils and hard freeze-thaw cycling cause gate posts to heave and shift every spring far more aggressively than in lower-altitude Front Range cities. In Baker and Curtis Park, by April it’s routine to find posts that were plumb in October now leaning 5 to 10 degrees. Fix the panel without the post and you’ll fix it twice. We dig the footing, pour a deeper concrete footing below the frost line, reset the post, and re-hang the gate so it clears the pad and the latch strikes clean.
Gate Realignment
Gate realignment in Denver is most often a springtime call. Wet, heavy spring snow loads hundreds of pounds onto a gate frame overnight, bending hinges and pulling a gate out of square. We straighten frames, re-shim hinges, and reset latch strikes. For alleys with shared driveways where a full removal would block vehicle access, we work the gate in place. The gate stays in your driveway. Your access stays open.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Denver
We’re certified to service nine major gate brands, and for Denver customers that includes Linear, Viking, Ghost Controls, and DoorKing. We stock common parts for these operators in our Denver office, which means we’re not waiting on a distributor in another state when a control board fails or a limit switch needed replacing yesterday. Bring us any gate, any brand, any age. If it’s a pre-standard hinge dimension on a Capitol Hill wrought-iron gate from 1920, we’ll measure it, weld it, and make it work. Modern off-the-shelf parts don’t fit forge-era hardware. We know that, and we work around it.
Common Gate Repair Problems We See in Denver Homes
- Frost-heaved hinge posts. Denver’s dense clay soils expand hard when frozen. By March thaw, posts that were plumb in October are leaning, the gate drops into the concrete pad, and the latch grinds past its strike. This is the dominant recurring repair call in Denver’s core ZIP codes.
- Wet spring snow damage. Unlike dry ski-season powder, Denver’s spring snow is heavy and wet. A single overnight storm can load hundreds of pounds onto a gate frame, buckling wooden planks and bending hinges on vintage wrought-iron gates that survived the dry winter just fine.
- Slide gate rack and pinion misalignment. The wide daily temperature swings cause metal hardware to expand and contract repeatedly. Slide gate racks loosen, pinions wear unevenly, and the gate starts jumping the track. This is common on shared-driveway slide gates in Curtis Park and Baker.
- High-altitude UV finish failure. Denver’s intense high-altitude UV accelerates paint, powder-coat, and wood finish degradation faster than at sea level. A gate that looked fine two years ago may be rusting through the finish now. We weld and re-finish on site.
Pricing for Gate Repair in Denver, CO
A typical hinge and post reset in central Denver runs $280-$520 depending on footing depth and whether the post is concrete, steel, or set in an old stone pier. Gate realignment and latch repair typically runs $160-$380. Electric gate operator diagnosis and minor board or limit switch replacement runs $190-$450. Automatic gate rack and pinion realignment runs $260-$600. Full on-site weld repair on a wrought-iron gate runs $180-$500 depending on the extent of the metal fatigue. These are real ranges for Denver’s market, quoted up front and agreed before any work starts. Every Denver job gets the 90-Day Done Right Promise in writing, plus $40 off any repair over $200. Call (877) 610-2993 for an exact quote. Estimates are free.
We Also Serve Cities Near Denver
Our Gate Repair team works throughout Denver proper and the close-in suburbs: Glendale, Edgewater, Lakewood, and Wheat Ridge. If you’re just outside the city line, call us. We schedule work by neighborhood, not by county border, and all of Gate Repair in Denver coverage includes the same live-answer phone, the same 90-Day Done Right Promise, and the same no-trip-charge-inside-the-county policy.
Serving Denver, CO - Our Local Coverage Area
We’re based in the Denver area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Denver
It’s not the hinges. It’s the post. Denver’s freeze-thaw cycle heaves the post a few degrees every winter, and by April the whole gate has shifted. In Capitol Hill and Cheesman Park, where ornamental wrought-iron gates are original to the late-Victorian and Craftsman lots, the post footings were often poured too shallow by modern standards. We dig the post out, pour a deeper footing below the frost line, and re-hang the gate so it clears the pad. Replace the hinges without touching the post and the gate will sag again next spring. Call (877) 610-2993 for a free quote on a post reset.
Usually both, and they feed each other. Denver’s daily temperature swings separate the rack from the gate frame and loosen the operator mount. Once the rack shifts, the pinion starts binding, and the gate walks off the track. We realign the rack, re-torque the mounts, and inspect the operator’s limit switches. The fix requires a technician who understands both the mechanical and electronic sides. That’s what we do. Call (877) 610-2993 and describe what you’re hearing. We’ll tell you if you can wait or if you should not run the gate until we look at it.
Yes, and it’s a fast failure. Denver’s spring storms drop wet, heavy snow that a wooden gate was never built to carry. Dry ski-season powder blows off. Spring snow sits and loads. A single March or April storm can add hundreds of pounds to a swing gate, buckling planks and bending iron hinges. That’s why April is our busiest month for wood gate repair in Baker and the Highlands. We replace rotted or buckled planks, straighten the frame, and upgrade the hinges so the next wet snow doesn’t fold the gate. Call (877) 610-2993 for a free estimate.
For narrow lots with a shared driveway, a slide gate usually fits better. Swing gates need clearance to arc into the driveway, and on a tight Baker alley lot that clearance may not exist. A slide gate rides on a track and takes no swing space. But a slide gate requires a straight, level run and good drainage beneath the track; if your alley has a steep grade or standing water, a swing gate might be the honest choice. We measure the site, look at the grades, and tell you which gate actually fits rather than selling you whichever one has a higher price tag. Call (877) 610-2993 and we’ll measure your alley lot.
Your gate needs working photo-eyes or edge sensors that will stop and reverse the gate if something is in the way. That’s UL 325, and Denver enforces it. Many older automatic gates in Cheesman Park and Capitol Hill were installed before this standard became universal. Homeowners discover the missing safety sensor only when the gate reverses unexpectedly, or worse, does not reverse when it should. Don’t test it with your body. Call us. We inspect the full entrapment-protection system, replace missing sensors, and test the gate under load before we leave. Call (877) 610-2993 for a safety inspection quote.
Denver Gate Repair You Can Verify
In Curtis Park (80205), our crew reset the hinge post on a 1940s wrought-iron alley gate off a shared driveway where the clay soil had heaved the post 8 degrees over winter. We dug the post footing, poured a deeper concrete footing below the frost line, and realigned the hinges so the swing gate cleared the pad and the original latch struck clean without losing a day of vehicle access. That’s the job. That’s what we do all spring across Denver’s alley-grid blocks, and it’s why the 90-Day Done Right Promise is stamped in writing, not buried in fine print.
Hal Gatewood’s name is on the shop, and the shop is down the road. That’s the oldest accountability there is. Call (877) 610-2993 for a free estimate on gate repair in Denver. A live person answers, day or night. You’ll get a straight price, a real appointment window, and a gate that works when it’s done.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Denver since 2001.