Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Clermont
A gate repair call in Clermont usually means one of three things: a hinge post has started leaning on a sloped driveway, a builder-grade operator has finally given up after years of fighting gravity, or lightning from a summer storm took out a control board. We handle all three, and we handle them the same week you call. Hal Gatewood has been fixing gates since 2001, and the person who shows up at your door in Clermont is the same person whose name is on the invoice. Call (877) 610-2993 and a live person answers, any hour.
Why Gatewood Fence & Gate Is Clermont’s Preferred Gate Repair Company
We work all over Clermont, from the hillside lots in Legends and Magnolia Park down to the flatter streets off State Road 50 near 34711. That matters, because a gate on a ridge-top slope fails differently than a gate on flat ground, and we have been seeing those failure patterns in Clermont for years. Our crew knows which operators burn out early on grade changes, which hinge post footings were poured too shallow back in the 2005-to-2010 building boom, and what a gate that has been twisting on its post for three seasons sounds like when it grinds.
Clermont homeowners call us because we repair before we replace. If a hinge post in the 34714 ZIP is leaning, we weld and reset it on site. If a gate in Kings Ridge is dragging and the motor is straining, we fix the realignment instead of selling a new operator. And every single job, in every Clermont neighborhood, carries the 90-Day Done Right Promise in writing. One call brings Hal back. No runaround.
We also answer the phone. Not a voicemail, not a chatbot, not a queue that routes you somewhere else. A live person picks up 24/7, and if your gate is stuck open at 6 a.m. before work, someone is already on the way while you are still on the line. Scheduling is coordinated from our South Florida office, but crews serve Clermont directly every week.
Our Gate Repair Services in Clermont
Electric Gate Repair
Most electric gate failures in Clermont come down to the control board, the safety edges, or the power supply. Lightning is the usual suspect here. Clermont gets near-daily summer thunderstorms, and a strike half a mile away can induce enough voltage on a gate loop or keypad line to fry a board. We diagnose on site, stock common boards and safety edge replacements for Clermont jobs, and repair what is actually broken rather than quoting you a full operator swap because it is easier for us.
Automatic Gate Repair
Automatic gates on Clermont’s sloped driveways work harder than the same operator on flat ground in Kissimmee or Sanford. The motor is pushing or pulling against gravity every cycle. That means gears strip faster, limit switches wear sooner, and the operator that worked fine on paper when the builder picked it struggles from day one on a hill. We replace what failed and, when the operator was undersized for the slope from the start, we recommend and install slope-rated units from brands like FAAC, BFT, Linear, and Viking so the next repair is years away instead of months.
Hinge & Post Repair
We recently rebuilt a swing gate in the Legends community on a slope where the builder-grade LiftMaster operator had burned out after years of fighting gravity. Our crew cut out the failing hinge post, poured a deeper post footing with extra concrete, and replaced the twisted hinges before remounting the rack and pinion so the gate swung freely for the first time since install. That is the job, in Clermont, maybe one call out of three. The gate sags in the post, not in the middle, and we start where the problem actually is.
Gate Realignment
A gate that drags across the driveway, catches on the latch, or leaves a gap at the closing edge is usually out of plumb. In Clermont, the post has often started leaning downhill, which pulls the whole gate panel out of square. Fixing it means digging out the old footing, resetting the post deeper and wider, and remounting the gate so it swings or slides true. Skip the post and you will fix the gate twice. We do the footing work the first time.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Clermont
We are certified to service nine major gate brands, and we carry a working inventory of parts for the ones Clermont sees most: FAAC, BFT, Linear, and Viking. That means when your FAAC control board fails after a storm, we are not ordering parts and making you wait a week with the gate propped open. We carry common boards, hinges, safety edges, and receiver modules. If a brand has a known weak point on Clermont’s terrain, we know it before we show up.
Common Gate Repair Problems We See in Clermont Homes
- Hinge posts leaning downhill on sloped lots. Clermont sits on the Lake Wales Ridge, one of the hilliest areas in Florida, and a post set in shallow concrete on a grade will start tilting within a few years. The gate then falls out of alignment and the operator works against the whole weight of the panel.
- Builder-grade operators overheating on inclines. Most 2000s-era Clermont HOA communities were built with basic operator packages. On a slope, those motors run hot, strip gears, and fail years earlier than they should.
- Lightning damage to control boards and keypads. Clermont’s summer thunderstorm season is brutal on gate electronics. A board fried by an induced surge is one of our most common same-week repair calls across 34711 and 34712.
- Missing conduit runs on retrofitted automation. A lot of Clermont gates were installed manual because the builder did not run power or low-voltage conduit to the gate. Adding automation later means running new conduit properly, not leaving exposed wiring where weed trimmers and car tires find it.
Pricing for Gate Repair in Clermont, FL
Here are honest numbers for Clermont’s market. A hinge and post repair runs $325 to $650 depending on how deep we dig and whether the post needs replacing or just resetting. Gate realignment typically falls between $250 and $475. Electric gate repair, like a control board or safety eye replacement, runs $180 to $520 depending on the part and the brand. A full operator replacement on a slope-rated unit usually lands between $1,100 and $2,400 installed. Every price is quoted and agreed in writing before work starts, with no trip charge inside Lake County. We also take $40 off any repair over $200, and seniors and veterans get a permanent 10% discount. Call (877) 610-2993 for an exact quote and a free second opinion on any written estimate you already have.
We Also Serve Cities Near Clermont
Our Gate Repair team works throughout the communities around Clermont as well: Minneola, Winter Garden, Ocoee, and Horizon West. If you are within a short drive of Clermont and your gate is down, call us. We are already working in the area most weeks.
Serving Clermont, FL - Our Local Coverage Area
We’re based in the Clermont area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Clermont
Your hinge post footing was likely poured too shallow for the slope. Clermont sits on the Lake Wales Ridge, and over years the post slowly tilts downhill, pulling the gate out of plumb and forcing the operator motor to grind against the added friction. The fix is resetting the post with a deeper, wider footing, not just greasing the hinges. Call (877) 610-2993 and we will inspect it in person.
Yes. We do it regularly in Clermont. The catch is that many of those gates were built without conduit or a power run, so the job means trenching and running proper electrical and low-voltage lines before mounting the operator, arms, and safety edges. We quote the full job upfront, including the conduit work, so you know the real number before we start.
No. The photocell itself or the wiring to it is almost always the failed part, not the gate structure. We test the eye, the wire run, and the control board input to isolate exactly what took the hit, then replace just that component. Call (877) 610-2993 and we will come out and diagnose it before you spend money on parts you do not need.
If the gate jerks or binds in one specific spot along the track, the rack or pinion gear is worn or misaligned. If it moves stiffly but smoothly, lubrication is probably the first step. In Clermont, rack and pinion wear happens faster on sloped driveways because the motor is always pulling against grade. We will inspect the teeth and tell you which it is, without selling a replacement you do not need.
Water is getting into the operator housing, the junction box, or a splice somewhere. Clermont’s hard groundwater leaches mineral deposits that corrode connections over time, and a hard rain is usually enough to cause a short at the weakest point. We find the intrusion point, seal or rerun the affected wiring, and restore the circuit. Call (877) 610-2993 for a same-week repair.
What to Do Next if Your Gate Is Failing in Clermont
If your gate is leaning, grinding, or dead after a storm, call us. Hal Gatewood picks up the phone, and a live person is there 24/7. We serve every Clermont ZIP, from 34711 near downtown out to 34714 by the ridge. We will give you an honest diagnosis, a written price before any work starts, and the 90-Day Done Right Promise behind every repair. The name is on the shop, and the shop is down the road. That is the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Clermont since 2001.