Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Buda
Gate repair in Buda, TX typically runs $185 to $480 for common fixes like hinge post resets, opener control board swaps, and track realignment. The bigger problem here isn’t the gate itself; it’s the clay. Buda sits on Blackland Prairie soil that swells every spring and cracks every August, which is why a gate that worked fine in December is binding by March. We’ve been chasing that exact failure mode across Sunfield, Whispering Hollow, and Garlic Creek long enough to know what to look for before you lose access to your driveway. Call (877) 610-2993 and a live person answers, day or night.
Why Gatewood Fence & Gate Is Buda’s Preferred Gate Repair Company
We’re not a franchise and we don’t route calls through a queue. Hal Gatewood started this shop in 2001 and his name is on the door. Our Gate Repair crew works the Buda area weekly, and we’ve seen the same subdivisions enough times to know which production builders used which openers and which post footings. When a Ghost Controls operator in Garlic Creek fails, we already know the install habits that caused it.
Buda homeowners call us because we weld on site instead of hauling your gate to a shop. That matters when your driveway is the only way in and out. We also stamp the 90-Day Done Right Promise on every invoice, in writing. If it’s not right, one call brings us back. No runaround. No “that’s not covered.” And our published address and license number mean you can look us up or drive to the shop and look Hal in the eye.
Our Gate Repair Services in Buda
Hinge & Post Repair
The hinge post is where every sagging gate actually fails. The panel just hangs from it. On Buda’s swelling clay, a post set in a shallow footing heaves out of plumb within a few wet-dry cycles, and the gate starts dragging or latching wrong. We dig past the active soil layer, set the post deeper, and weld the hinge assembly square so it stays put. We do this work in your driveway, not our shop.
Gate Realignment
Slide gates on the newer I-35 corridor communities bind when the rack and pinion get pushed out of line by post movement. A gate that grinds or stalls halfway is usually a rack alignment problem, not a dead motor. We check the track, the post, and the rack together, because fixing one without the other means you’ll call us again in six months. The clay heave in 78610 makes this a recurring job, not a one-time patch.
Electric Gate Repair
Buda’s automated gates took a beating during Winter Storm Uri. Hydraulic and electromechanical operators that froze in February 2021 are still failing intermittently, tripping breakers, or frying control boards after power surges. We service LiftMaster, DoorKing, Elite, and Ghost Controls openers, and we carry the common boards and safety photocells on the truck so we’re not waiting on parts when you’re locked out.
Automatic Gate Repair
When a production-built opener from 2016 or 2017 dies, you don’t always need a full replacement. We’ve swapped plenty of fried control boards and rebuilt stripped rack gears at half the cost of a new unit. But if the opener is beyond saving, we’ll tell you straight and quote a replacement before any work starts. We also install solar gate openers for acreage gates off FM 967 and Old Bastrop Road where trenching grid power isn’t practical.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Buda
We’re certified to work on nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Around Buda, the bulk of what we see in Sunfield and Garlic Creek is LiftMaster and Ghost Controls hardware from the 2015-2019 build wave. We stock replacement boards, photocells, keypads, and rack sections for those brands so most repairs happen same day. If you have a Viking or DoorKing operator on an older ranch gate, we handle those too.
Common Gate Repair Problems We See in Buda Homes
- Clay-heave post shift. Spring rains swell the soil under post footings, pushing swing and slide gates out of plumb. The gate drags, binds, or refuses to latch, and the fix is always the footing, not the panel.
- Freeze-cracked operators from Uri. Hydraulic and electromechanical openers that survived the 2021 freeze are now failing intermittently as internal seals and circuit boards degrade. They’ll work for a week, then trip a breaker.
- Dead photocells and keypads on HOA gates. Sunfield and Garlic Creek entrances sit in full UV exposure and take power surges. Safety edges and photo eyes go dark, which is an entrapment hazard, not just an inconvenience.
- Sagging wrought-iron swing gates on newer builds. The panel looks straight, but the latch side drags. That’s almost always the hinge post leaning, and tightening the hinge bolts won’t fix it. The post has to be reset.
Pricing for Gate Repair in Buda, TX
Most Buda gate repairs land in these ranges: hinge post reset and re-weld, $225 to $420 depending on footing depth and access; slide gate realignment with rack adjustment, $185 to $320; control board replacement, $240 to $480 including the part; solar gate opener installation on a ranch gate, $680 to $1,100 for the opener and mounting. These are honest Buda market numbers, not bait. The price we quote on the phone is the price on the invoice. We walk the gate with you before any work begins, and you approve the number in writing. We also knock $40 off any repair over $200, and seniors and veterans get a permanent 10% discount. Call (877) 610-2993 for a free estimate.
We Also Serve Cities Near Buda
Our Gate Repair in Buda service area reaches into the surrounding communities, including Shady Hollow, Kyle, Austin, and Hornsby Bend. If you’re on the county line or just outside city limits, call and we’ll confirm coverage. No trip charge inside the county.
Serving Buda, TX - Our Local Coverage Area
We’re based in the Buda area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Buda
Because Buda sits on Blackland Prairie clay that swells with spring rain and shrinks in summer drought. That seasonal heaving moves shallow post footings a fraction of an inch at a time, and after a few cycles your gate is out of plumb enough to bind or drag. The fix is a deeper footing that reaches below the active moisture layer. If you’ve had the gate realigned twice and it keeps coming back, the post itself was never set deep enough. Call (877) 610-2993 and we’ll dig it out and do it right.
If the motor itself spins smoothly and the failure is electrical, a control board replacement at $240 to $480 usually gets another few years out of the unit. If you’ve already replaced the board once, or the gear teeth are stripped, replacement makes more sense. We ran a Sunfield call last month where a 2016 LiftMaster slide operator fried its board after a storm, and the rack gear was stripped because the post had shifted on the clay. We re-set the post, corrected the rack, and installed the new board. The customer paid about $450 total instead of $900 for a new opener.
Yes. Solar gate openers are a standard install for us on acreage gates along FM 967 and Old Bastrop Road where trenching grid power would cost more than the opener. We size the panel and battery to the gate width and daily cycle count, and we install everything on site. A typical solar opener installation for a heavy ranch gate runs $680 to $1,100 including the opener, panel, and mounting hardware. Call (877) 610-2993 for a written quote.
Yes, and it’s also an access problem. A faulty loop detector can prevent the gate from closing, or worse, fail to detect a vehicle and close on it. That’s an entrapment hazard. We replace loop detectors and re-tune the sensitivity, and we check the safety photocells at the same time. HOA entrance gates need to close reliably, but they also need to stop instantly when something is in the path. We stock loop detector modules for LiftMaster and Elite systems so HOA gates in Buda can be back online same day.
Because the hinge post is leaning, not the panel. Wrought iron gates are rigid; they don’t sag in the middle. The post itself has shifted out of plumb, usually from clay heave or an undersized footing. We re-set the post, weld the hinges square, and rehang the gate so the latch lines up. Tightening the hinge bolts or welding a brace onto the panel won’t fix the post. Call (877) 610-2993 and we’ll come look at it before you spend money on the wrong fix.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Buda since 2001.