Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Bayonne
Most gate problems in Bayonne come down to one thing: the salt air off Newark Bay and the Kill Van Kull never stops working on your hinges, posts, and hardware. A gate that worked fine in September is binding by February. We know because we fix it every week, all over 07002. Hal Gatewood has been at this since 2001, and the Gate Repair work we do in Bayonne starts with a real person answering the phone. Call (877) 610-2993 and you’ll get a straight answer about when we can be there, not a recording.
We show up with a truck stocked for Bayonne’s older gates: hinge pins, post brackets, weld rod, rust treatment, and short-arm operator kits. You’ll get a price before any work starts, in writing. No surprises at the door.
Why Gatewood Fence & Gate Is Bayonne’s Preferred Gate Repair Company
We’re a small shop, not a franchise. Hal Gatewood’s name is on the building and on every invoice. He answers the phone himself when he’s not under a gate with a welder. People in Bayonne stay with us because we repair the gate they have instead of trying to sell them a new one. A gate sags in the hinge post, not in the middle, and that’s where we start.
Response time to Bayonne is usually same day or next morning, because our New York City office schedules directly with the crew that serves Gate Repair in Bayonne and the surrounding Hudson County towns. No dispatch queue, no third-party call center. When you call, a person picks up. When we say a time, that’s the time. Every job carries the 90-Day Done Right Promise in writing: if it’s not done right, one call brings us back.
You can also drive to the shop and look Hal in the eye before you ever hire us. Published address, published license number. That’s the oldest accountability there is, and it still works.
Our Gate Repair Services in Bayonne
Most Bayonne homes were built between 1890 and 1920. The gates are ornamental iron or older tubular steel, the posts are set in concrete that’s been crumbling for decades, and the openings are tight. We focus on the work those conditions actually require.
Hinge & Post Repair
Bayonne’s freeze-thaw cycles push clay soil against post footings every winter, and within a few seasons the post is leaning and the gate drags. We dig out the footing, reset the post plumb, brace it properly, and pour new concrete. We also replace hinge pins that salt air has eaten down to a fraction of their original thickness. Fix the panel without the post and you’ll fix it twice.
Weld & Rust Repair
Uncoated steel and iron in Bayonne corrode measurably faster than in inland Hudson County towns. Hinge pin bores, lower rails, and post bases rust through in under five years when they’re near the water. We provide on-site welding in Bayonne, in your driveway, cutting out the rusted section and splicing in new steel, then treating the whole area so it doesn’t come back next season. The gate never leaves your property.
Gate Realignment
When a gate stops latching or the operator starts struggling, the frame is usually out of square. Salt corrosion plus post movement will do that. We adjust posts, shim hinges, and reset the geometry so the gate closes true. We also check the operator travel limits afterward, because a realigned gate that slams is a new problem you didn’t have before.
Electric Gate Repair
Automatic gate operators in Bayonne fail in predictable ways: corrosion on the control board terminals, moisture in the arm, sensors knocked out of alignment by post movement. We service LiftMaster, Linear, Viking, Ghost Controls, and DoorKing units, and we carry boards, remotes, and photocells with us. Most electric repairs are done in one trip.
Automatic Gate Repair
Same-day access control repairs in Bayonne for gate arms, keypads, loop detectors, and safety sensors. Safety edges and photocells are not optional on a working family driveway, especially one with kids walking to school. We test everything before we leave, and we’ll show you how to test the safety reverse yourself.
Lock Repair
Wrought-iron gates on old Bayonne houses often still have their original mechanical locks, and the salt air gets into those too. We rekey, free up seized cylinders, and replace broken latch hardware. For automatic gates, we add electric locks that work with the operator instead of fighting it.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Bayonne
We’re certified to service nine major gate brands, and on any given week in Bayonne we work on three or four of them. Linear and DoorKing operators are common on the older slide gates behind two-family houses. Ghost Controls and Viking show up on newer residential retrofits where a swing gate wasn’t originally automated. Because Bayonne has so many short-arm conversions and slide retrofits, we stock the parts and brackets this market actually needs. If you’re not sure what brand your operator is, take a picture of the serial plate and we’ll identify it over the phone.
Common Gate Repair Problems We See in Bayonne Homes
- Salt-ravaged hinge pins and post bases: The tidal air from Newark Bay and the Kill Van Kull strips unprotected steel fast. Hinge pins thin out, gates sag, and bind. We replace pins and weld on reinforced post caps as a permanent fix.
- Frost-heaved posts in clay soil: Bayonne sits on dense clay that expands and contracts with every freeze. Posts tilt, latch plates misalign, and automatic operators jam. Resetting the footing is the fix, not just pushing the post back.
- Swing gates too wide for their own good: A ten-foot opening between two attached row houses leaves no room for a standard operator arm. Short-arm kits or slide conversions are often the only safe way to automate these gates in Bayonne.
- Rust-through on lower rails and pickets: The bottom 12 inches of a gate near Bayonne’s waterfront lives in constant salt spray. We cut out and splice rusted lower rails in place, so you keep the gate your house has stood with for a century.
Show me the gate closing on its own and I’ll show you where it’s failing. That’s the first thing we look for.
Pricing for Gate Repair in Bayonne, NJ
A typical hinge and post reset in Bayonne runs $260-$540 depending on how deep the footing goes and whether the concrete needs full replacement. Weld and rust repair on a lower rail or hinge boss runs $140-$320. Gate realignment, including operator travel and limit adjustment, runs $120-$280. Electric gate troubleshooting and board replacement starts around $150 and averages $220-$400 with parts. Full short-arm operator retrofit, including safety photocells and new brackets, typically runs $850-$1,400 installed.
| Bayonne Gate Repair Service | Typical Price Range |
|---|---|
| Hinge & post reset | $260 - $540 |
| Weld & rust repair (per section) | $140 - $320 |
| Gate realignment & operator adjustment | $120 - $280 |
| Electric gate troubleshooting & board replacement | $220 - $400 |
| Short-arm automatic gate retrofit | $850 - $1,400 |
Every quote is written, and the price is agreed before we start. You get our standing offers too: $40 off any repair over $200, no trip charge inside Hudson County, free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 for a free estimate on your Bayonne gate.
We Also Serve Cities Near Bayonne
Our crews work daily in Elizabeth, Jersey City, Harrison, and Kearny. If you’re in one of those towns and need a gate fixed fast, the same local crew that serves Bayonne can get to you, usually within a day. Same pricing, same Gate Repair standards, same 90-Day Done Right Promise in writing.
Serving Bayonne, NJ - Our Local Coverage Area
We’re based in the Bayonne area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Bayonne
Bayonne is a peninsula with saltwater on three sides: Newark Bay, Upper New York Bay, and the Kill Van Kull. That constant salt-laden air accelerates corrosion on uncoated steel and iron hardware, often cutting the life of hinge pins and post bases in half compared to inland towns like Kearny. In Bayonne, rust remediation is the core of nearly every gate repair we do. Call (877) 610-2993 and we’ll tell you what’s rusting out and what to do before the gate sags.
Yes, usually. Standard swing-arm operators need clearance that Bayonne’s narrow row-house driveways often don’t have, so we specify short-arm kits or convert the gate to a slide configuration. Both approaches keep the gate from hitting a wall or fence, and we add safety photocells so foot traffic from a second-family side entrance always stops the gate. We’d measure the opening and give you a written price first.
Yes. Bayonne’s clay-heavy soil holds water, and when it freezes and thaws, the expansion heaves post footings out of plumb. A post that’s leaning every spring needs the footing dug out, reset, and re-poured so it stops shifting. We do this all winter long in 07002, and the fix lasts because we address the footing, not just the angle of the post. Call (877) 610-2993 for a free assessment.
We work around you and your tenants. On a narrow shared driveway off Avenue C, we reset a leaning hinge post in clay soil that had heaved out of plumb over winter, then cut and spliced a rusted lower rail on a tubular-steel swing gate. A short-arm LiftMaster operator was fitted because the ten-foot opening couldn’t swing a standard arm without hitting the neighbor’s wall, and we added safety photocells to keep the gate stopping for foot traffic from the second-family side entrance. We never leave a shared driveway blocked; pedestrian access stays flowing while we work.
No. Automatic gates in New Jersey are required to have functional safety devices: either safety edges, photocells, or both, plus a reversing mechanism that stops the gate on contact or before contact. A gate that closes too fast and doesn’t stop is not code-compliant and is a serious safety risk, especially around children. We inspect and test every operator we work on, and we’ll fix the safety system as part of the repair. Call (877) 610-2993 if your gate is closing fast; this one should not wait.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Bayonne since 2001.