Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Wyandotte
Gate parts and welding repair in Wyandotte typically runs $180-$520 depending on whether we’re replacing a hinge, re-setting a post, or welding a cracked rail back square. Most jobs are finished the same visit, and we’re usually at your house within a day of your call. Hal Gatewood has been doing this work since 2001, and when you call (877) 610-2993, a live person picks up. Not a voicemail. Not a phone tree. Somebody who knows gates.
We work all over Wyandotte, from the brick bungalows near Oak Street down to the river side of Biddle Avenue, and the rear-alley garages along the numbered streets in between. The 48192 zip is home turf for us. If your gate sags, drags, or won’t latch, we’ll tell you honestly whether it needs a weld, a new post, or a full replacement. Often the answer is cheaper than you think.
Why Gatewood Fence & Gate Is Wyandotte’s Preferred Gate Parts & Welding Company
We’ve been fixing gates in Wyandotte long enough to know that the rear service alleys behind nearly every pre-war block create a specific kind of wear you won’t find in the wider-lot suburbs to the south. Garbage trucks clip gate leaves. Delivery vans push bottom rails out of square. Frost heaves the shallow post footings that were poured when these houses were built, and by March, a gate that was plumb in October is sitting two or three inches off-square. Hal’s crew sees it every spring, and we fix it the right way: on site, with the gate still hanging in your driveway where it belongs.
When a Wyandotte homeowner calls us, they get Hal or one of his small crew. Uniformed, background-checked, and local enough that you’ll probably see the truck at a Downriver hardware store the same week. Every job carries the 90-Day Done Right Promise in writing. If it isn’t right, one call brings us back. The name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
Our Gate Parts & Welding Services in Wyandotte
Hinge Replacement
On Wyandotte’s older steel and ornamental gates, the hinge is almost always the first thing to go. The dense grid of pre-WWII lots means many gates swing into tight clearance, and any sag puts extra load right on the hinge pins. A typical hinge replacement in Wyandotte runs $140-$240 per hinge, including cutting off the old one and welding or bolting the new one in place. We stock heavy-duty barrel hinges and adjustable weld-on hinges so we’re not running back to a supplier mid-job. If the hinge tore out of the post, see below – the post is usually the root problem.
Post Replacement
Frost-heaved posts are the signature failure mode in Wyandotte. The older alley infrastructure has shallow footings, and the Detroit River keeps the groundwater high enough to make every freeze-thaw cycle count. We dig the old footing out, set a new steel post at 30 to 36 inches deep, and tamp it in with clean gravel before the concrete goes in. In Wyandotte, post replacement with labor and materials typically runs $280-$450 for a standard 2-inch or 2.5-inch gate post. If the old post is still straight and just loose, we may be able to re-set it for $180-$240. Either way, the price is agreed before we dig.
Rail Repair
Alley-facing gates in Wyandotte take a beating from delivery trucks and garbage trucks that don’t always clear the swing. Bent bottom rails are the most common consequence, especially on chain-link and older welded steel gates behind detached garages. We straighten what’s salvageable and cut-and-weld what isn’t. A typical rail repair runs $150-$300, including the steel and the welding. If the rail is rusted through near the hinge, welding a fish plate or new section is often cheaper than a full gate replacement-and it holds up to the next garbage truck hit. No promises about the truck itself.
Custom Welding
This is where we do our best work, and Wyandotte’s housing stock gives us plenty of it. The 1910s-to-1950s bungalows and two-story homes on those narrow 30-to-40-foot lots often have original ornamental wrought iron or mid-century chain-link gates that no off-the-shelf part fits. Tight side-yard passages, some as narrow as three feet, mean pedestrian gates need custom swing clearances and compact hardware. Hal welds on site, in your driveway, and fabricates brackets, extensions, and bracing to match what’s already there. Custom welding work in Wyandotte typically runs $120-$400 depending on how much steel and time the job needs. If it can be welded, that’s the fix we recommend before we ever talk about replacement.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Wyandotte
We service and retrofit operators from FAAC, BFT, Linear, and Viking, along with several others. When a Wyandotte homeowner has an old operator from the 1970s or 80s with an obsolete control board, we’ll tell you straight whether a retrofit is worth doing. Sometimes the answer is yes: a new board and a set of photo-eyes can bring a solid old Viking back to life. Sometimes the wiring chases in a 1950s bungalow are too narrow for modern cable runs, and a new operator with a smaller control footprint is the cheaper answer. We keep a running stock of common replacement parts and hardware that fits the gates we see most around here, so most repairs don’t wait on a parts order.
Common Gate Parts & Welding Problems We See in Wyandotte Homes
- Frost-heaved post footings on pre-1945 garage gates. Every spring we find rear garage gates that were plumb in October now shifted 2-3 inches off-square. The hinge posts heave out of shallow footings, and the whole frame racks. The hinges might be fine. The post isn’t. Reset the post, and the gate swings true again.
- Alley-facing swing gates struck by garbage trucks. Wyandotte’s rear service alleys mean your gate spends its life a few feet from a truck that doesn’t care about it. Bent bottom rails, sheared hinge pins, latches that no longer meet the strike plate. This is the most common damage we weld, straighten, or replace parts for.
- Legacy operators with no entrapment protection. A lot of Wyandotte bungalows still run gate operators from the 70s, 80s, and 90s, with control boards that predate modern safety requirements. These older boards often can’t support a proper photo-eye retrofit, and the wiring chases in the older homes are too narrow to pull new cable anyway. A modern operator with integrated safety is usually safer and cheaper in the long run.
- Stripped hinge threads from repeated stress. On older ornamental gates, the hinge threads inside the post eventually give up. Tight clearances, spring racking, and decades of use all contribute. When the hinge won’t stay tight no matter what, it’s a post-side repair, not another crank on the bolt. We re-tap where possible, weld in a threaded insert where not, and replace hinge and post together when that’s what the gate needs.
Pricing for Gate Parts & Welding in Wyandotte, MI
Here’s what we charge in Wyandotte right now. Hinge replacement: $140-$240 per hinge. Post replacement: $280-$450 for a standard post, $180-$240 to re-set an existing post that’s still straight. Rail repair: $150-$300. Custom welding: $120-$400 depending on the job. These are the numbers you should expect to see on a written estimate, and the price you agree to is the price you pay. No trip charge inside the county. Seniors and veterans get 10% off, permanently. Repairs over $200 get $40 off, no haggling. If you’ve got a written estimate from another company, bring it in and we’ll give you a free second opinion. Call (877) 610-2993 and we’ll set a time.
We Also Serve Cities Near Wyandotte
Our Gate Parts & Welding crew covers Wyandotte and the surrounding Downriver communities. If you’re in Southgate, Lincoln Park, Ecorse, or Allen Park, you’re still in our service area. The same people, the same written guarantee, the same phone number. If you’re in Wyandotte proper, we’ll be there as fast as anyone in the county.
Serving Wyandotte, MI - Our Local Coverage Area
We’re based in the Wyandotte area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Wyandotte
It depends on the post. If the steel is sound and the footing is just frost-heaved, we can often re-set the same post at a deeper depth, around $180-$240. If the post is rusted through at the base or the hinge threads are stripped, replacement is the honest answer, typically $280-$450. We’ll tell you which one you need before any work starts. Call (877) 610-2993 and we’ll come out and look at it.
Because your gate lives in a rear service alley, and the garbage truck that empties the cans behind your garage swings close enough to put side-load on the gate every week. That repeated stress works the hinge pins and threads loose, even when the gate itself looks straight. The fix is usually a heavier-duty hinge and a good look at the post. If the post is flexing because the footing is shallow, no hinge will hold long-term. We stock heavy barrel and weld-on hinges made for exactly this kind of abuse.
Usually, yes. We match compact operators to tight rear clearances, the kind of thing we did on an alley gate off Oak Street last March: an 8-foot alley setback, a LiftMaster LA400, and a gate that had been racked 2.5 inches out of square by frost. We cut and re-welded the bottom rail, reset the post, and the operator fit where no off-the-shelf kit would. If your gate frame is straight and the hinges are sound, a retrofit is often $400-$700 less than a full replacement. We’ll measure it and give you a written number.
If the gate frame needs welding, we can weld it. But a 1980s operator with no photo-cell is a safety hazard, and many of those old control boards can’t accept a modern entrapment-protection retrofit. The truth: a gate that closes on a person or an animal is the kind of liability no repair fixes. When the frame is still solid, we often install a new operator with integrated safety and keep the old gate. If the operator is obsolete and the frame is tired, replacement is the cheaper long-term answer. We’ll show you both numbers and you decide.
The frame needs to be cut and re-welded, and the post needs to be checked. A truck hit doesn’t just bend the gate; it usually racks the post too. We’d cut the deformed bottom rail, weld in a new section, and then re-square the frame against the post. If the post moved, we reset it at a proper depth. A job like that in Wyandotte typically runs $300-$500 all in. Call (877) 610-2993 for an exact quote-estimates are free, and the price is set before we touch a thing.
Call Gatewood Fence & Gate for Gate Parts & Welding in Wyandotte
If your gate drags, won’t latch, or came out of this winter sitting cockeyed, call (877) 610-2993. You’ll get a live person, a straight answer, and a time when we’ll be there. Hal Gatewood has been fixing gates since 2001, and his name is on every job. No voicemail maze, no call center in another state. Just a local company that welds on site and stands behind the work with a 90-Day Done Right Promise. In Wyandotte, when a gate acts up on a rear alley or a tight side yard, we’re the ones to call.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Wyandotte since 2001.