Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Woodinville
Gate parts and welding in Woodinville usually means one of two things: a hinge or post that finally gave out, or a weld that cracked on a gate that gets opened and closed a hundred times a week. We handle both, and we do the work on site, in your driveway, without hauling the gate off to some shop. Hal Gatewood has been fixing gates since 2001, and the crew that shows up in Woodinville is the same crew that answers the phone when you call (877) 610-2993. If your gate sags, scrapes, or won’t latch, we’ll tell you what’s actually wrong before we touch a tool.
Why Gatewood Fence & Gate Is Woodinville’s Preferred Gate Parts & Welding Company
Woodinville is not Redmond or Kirkland. Drive through the 98077 ZIP and you’ll see it right away: long private driveways, horse properties, custom estate entrances, and winery gates along SR-202 that get more traffic in a weekend than a subdivision gate gets in a month. We know that profile because we work it every week. When a hinge post rusts out on a tubular steel ranch gate off 156th Ave NE, we don’t guess. We cut the old post, set the new one in concrete, weld the hinges back square, and realign the panels so the gate swings clean. That’s what Gate Parts & Welding means to us: the part gets replaced and the weld gets done right, in one visit.
Every Woodinville job carries the 90-Day Done Right Promise in writing. If something isn’t right, Hal comes back. No runaround, no phone tree. Our calls are answered by a live person 24/7, because a gate that won’t open at 6 a.m. on a Tuesday is a problem that can’t wait for a callback. We’re licensed, insured, and bonded, and the person who shows up is background-checked and in uniform. The name on the shop is the name on the invoice, and the shop is down the road. That’s the oldest accountability there is.
Our Gate Parts & Welding Services in Woodinville
Hinge Replacement
Most gate failures in Woodinville start at the hinge. Forty-five to fifty inches of annual rain will find its way into a hinge pin, and once the rust starts, the gate begins to sag until it scrapes the driveway or binds against the post. We replace hinges on swing gates, ranch gates, and decorative estate entrances, and we weld the new hardware in place rather than bolting it and hoping. A gate sags in the hinge post, not in the middle, and that is where we start. Hinge replacement on a standard Woodinville driveway gate typically runs $280-$550, including hardware and on-site welding.
Post Replacement
Rust jacking is the quiet killer of gate posts in Woodinville. Rainwater pools at the base of the post, rust expands against the concrete footing, and the post cracks or leans until the whole gate droops. We cut out the failed post, dig and set a new one in concrete, weld the hinge post in place, and realign the gate so it closes square. For properties in 98077 with long gravel driveways and heavy steel gates, post replacement is often the difference between a gate that keeps working and one that needs fixing every six months. Expect $450-$900 depending on post size and whether the old footing has to be broken out.
Rail Repair
On a wood or composite gate, the rails carry the weight, and when a rail rots or splits, the whole panel twists. That twist is what pulls the hinges out of line and makes the latch miss the post. We replace split or rotted rails, then re-square the panel and adjust the hinges so the gate closes without fighting you. Woodinville’s wet winters accelerate rail rot on wooden gates, especially north-facing ones that never fully dry out. Rail repair in Woodinville generally falls between $180 and $420, depending on the panel size and whether we’re splicing or replacing the full rail.
Custom Welding
Decorative wrought iron and powder-coated aluminum gates along the Woodinville-Redmond Road winery corridor look great and take a beating. Heavy weekend traffic means repeated open and close cycles, and stress fractures at welds are common. We do on-site custom welding to repair cracks before they become breaks, and we can match the existing decorative pattern so the repair doesn’t look like a patch. Whether it’s an SR-202 tasting room entrance or a private driveway gate in Cottage Lake, our custom welding keeps your gate in the driveway and out of a shop. Custom welding work in Woodinville typically runs $300-$700 per repair area, depending on the extent of the cracking and the finish work involved.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Woodinville
We’re certified to service nine major gate brands, including FAAC, BFT, Linear, and Viking, so when a circuit board fails or a limit switch stops reading, we can diagnose and repair it on site without waiting on a third-party vendor. For Woodinville customers, that means faster turnaround on operator repairs and less time with a gate stuck half-open. We keep common parts for LiftMaster, FAAC, and Linear on the truck, and we can order specialty components for BFT and Viking systems with next-day availability in most cases. If your gate opener is overworked because a hinge or post failed, we fix the mechanical problem first, then address the operator so you don’t burn out a new board six months from now.
Common Gate Parts & Welding Problems We See in Woodinville Homes
- Rust jacking at hinge post bases. Water collects where the post meets concrete, rust expands, and the footing cracks. The gate sags, scrapes the driveway, and eventually the post has to be replaced entirely. This is the single most common failure we see on 98077 ranch gates.
- Leaf and seed pod jams on slide gate operators. Alder and big-leaf maple drop enormous volumes of leaves and seed pods each fall. They pack around ground-mounted actuator housings and jam the rack and pinion on slide gates. A good cleaning and realignment fixes it; ignoring it burns out the motor.
- Stress fractures on decorative HOA gates. Gates on SR-202 winery entrances and in gated Woodinville communities cycle open and closed dozens of times a day. The repeated stress cracks welds at stress points. We catch these early with custom welding before a small crack becomes a dropped gate.
- Moisture in outdoor operator pedestals during long wet stretches. October through April is hard on gate automation in Woodinville. Circuit boards sealed poorly or with worn gaskets take on moisture, and keypads stop responding until things dry out. We reseal pedestals and replace corroded boards as part of the repair, not as a band-aid.
Pricing for Gate Parts & Welding in Woodinville, WA
Here are Woodinville market ranges for the work we do most often. Hinge replacement runs $280-$550. Post replacement runs $450-$900. Rail repair runs $180-$420. Custom welding runs $300-$700 per repair area. Gate operator repairs after a mechanical fix typically run $250-$600, depending on the part. Every price is quoted and agreed on before any work starts. You won’t see a higher number at the door. We also have standing offers that don’t require haggling: $40 off any repair over $200, no trip charge inside the county, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 for a free estimate on your specific gate.
We Also Serve Cities Near Woodinville
Our Woodinville service area extends to the communities around it. We work regularly in Maltby, Cottage Lake, Inglewood-Finn Hill, and Kingsgate. If you’re just outside Woodinville proper and wondering whether we’ll come out, the answer is almost always yes. Same crew, same pricing, same 90-Day Done Right Promise.
Serving Woodinville, WA - Our Local Coverage Area
We’re based in the Woodinville area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Woodinville
In most Woodinville gated communities, yes. If your HOA has architectural guidelines covering gate style, height, finish, or even hardware type, welding a new gate onto an existing post usually counts as a modification that needs written approval first. The approval often covers the gate itself, not the weld, but the HOA may also care about whether the new gate matches the community’s design standard. We’ll help you figure out what your board or management company needs to see, and we’ll coordinate the work timing so it’s done in the approved window. For anything involving shared entry systems or resident access, don’t even start without the management company in the loop. Call (877) 610-2993 if you want to talk through what your HOA is asking for.
It can be either, but in Woodinville it’s usually the post. The sag you notice in autumn is often a hinge post that’s been slowly rusting at the base all year, and the extra weight of wet leaves and moss on the panel finally makes the sag obvious. A hinge problem by itself won’t typically drop the gate that much unless a hinge pin is badly worn. We’ll inspect the post footing, check the hinge welds, and tell you which one is actually failing before recommending anything. Fix the panel without the post and you’ll fix it twice. Estimates are free, so call (877) 610-2993 and we’ll come look.
Yes, we match the pattern and profile as closely as the original material allows. Older wrought iron on Woodinville winery entrances often has hand-forged scrollwork that isn’t reproduced off the shelf, but we can form and weld replacement sections that read as continuous with the original, especially after finish work. We’ll also match the finish so the repair doesn’t stand out. If the gate is powder-coated aluminum rather than iron, we’ll usually replace the damaged section rather than weld it, since aluminum welding on thin decorative sections is rarely the right repair. Call (877) 610-2993 and we’ll take a look and tell you straight what’s possible.
In Woodinville, it’s almost always debris in the track or packed around the actuator housing, not the operator itself. Alder and maple seed pods wash down the driveway in fall storms and pack against the ground-mounted housing, binding the rack and pinion until the operator trips its overload. The operator might eventually fail from repeated jams, but the first fix is cleaning and realigning the track and housing, not replacing a motor. If the gate has been forced through jams repeatedly, we’ll inspect the rack teeth for wear while we’re there. Call (877) 610-2993 and we’ll diagnose it on site.
Very common. Woodinville’s wet season runs October through April, and keypads mounted on outdoor pedestals take on moisture through worn gaskets or hairline cracks in the housing. The circuit board gets damp, the buttons stop registering, and the keypad comes back to life only after a dry spell. That tells us the moisture is getting in, not that the board is dead. We’ll replace the gasket, seal the housing properly, and replace the board if corrosion has already set in. It’s a faster fix than most people expect. Call (877) 610-2993 for a quote, and don’t wait until the keypad fails completely.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Woodinville since 2001.