Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Westwood
Gate parts and welding in Westwood run into two recurring problems: frost heave that shoves posts out of alignment each spring, and road salt that eats hinge barrels and latch hardware on long driveway approaches. When a gate sags, binds, or stops closing, the fix usually involves more than swapping a part. We’ve been welding and repairing gates across Norfolk County since 2001, and we arrive for Gate Installation in Westwood with the right stock on the truck and the equipment to weld on site. If you’re off High Street, near the University Station corridor, or up a wooded lot near Clapboardtree Street, call (877) 610-2993 and a real person answers, day or night.
Why Gatewood Fence & Gate Is Westwood’s Preferred Gate Parts & Welding Company
Hal Gatewood started this shop in 2001, and his name is still on the door and on every invoice. Westwood homeowners call us because we repair the gate in the driveway instead of hauling it off to a fab shop. When you call, the person on the phone is someone who knows gate hardware, not a call script. We publish our address and license number, and we back every repair with the 90-Day Done Right Promise in writing. If it’s not done right, one call brings us back.
Our Gate Parts & Welding crew knows what a Westwood estate entrance demands. That means looking past the visible sag to the post below grade, the pillar anchor, and the operator’s safety loop. We don’t diagnose over the phone and we don’t quote one number and show up with another. The price you get before the work starts is the price on the invoice when we’re done.
Our Gate Parts & Welding Services in Westwood
Hinge Replacement
Westwood’s long private approaches mean gate hinges take a beating from road salt spray every winter. We replace corroded barrel hinges, adjust the gate’s geometry, and weld in the new hardware flush to the stile. A hinge replacement on a typical wrought-iron or aluminum driveway gate in Westwood runs $340 to $880 depending on gate weight and how much weld repair the frame needs.
Post Replacement
A gate sags in the post, not in the middle. Westwood’s frost line reaches about 48 inches, and any post set shallower than that will heave upward within a few seasons. We remove the old post, excavate to full depth, pour a proper footing, and set the new post plumb before re-hanging the gate. Post replacement on a brick-pillar entrance near University Station can run $900 to $2,400, because we’re anchoring into masonry and matching existing stone or brick work.
Rail Repair
When a gate rail bends or separates at the weld, the operator strains against it and eventually burns out limit switches. We straighten and weld rails in place or fabricate a new rail section when the old one is too far gone. Rail repair in Westwood typically runs $280 to $650. If the gate is off its track, we check the rack and pinion alignment at the same time, not just the weld.
Custom Welding
Some gates shouldn’t be replaced. When you’ve got an ornamental iron gate from the 1960s or 1970s that matches the house, we weld new steel into the existing frame, rebuild the hinge mounts, and preserve the look. Custom welding jobs in Westwood range from $180 for a latch reinforcement to $3,000 or more for a full frame rebuild with new operator mounts. We give you the written price before we strike an arc.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Westwood
We’re certified to service nine major gate brands, and Westwood’s older estates carry a few of them more than any others. Linear and DoorKing swing operators show up regularly on 1980s and 1990s builds, while Viking and Ghost Controls are common on newer installations. We keep stock parts for all of them in the truck, so most Westwood repairs get finished on the first visit. When an operator is discontinued or aftermarket-only, we’ll tell you that straight and lay out what retrofitting actually costs.
Common Gate Parts & Welding Problems We See in Westwood Homes
- Spring misalignment from frost heave. Westwood’s 48-inch frost line shoves gate posts up every thaw. A post that moves a quarter inch changes the swing geometry enough to throw off the auto-close and strain the operator. We see this every March on brick-pillar entrances near University Station.
- Salt-corroded hinges and latch hardware. Driveway salt spray from plowing and de-icing settles on the lower hinge barrels. After a few seasons, the barrel swells and the gate starts to sag. The motor and control board are usually fine; the hinge is the failure point.
- Obsolete control boards on legacy operators. Many Westwood gates still run original FAAC or Linear boards from the 1980s and 1990s. When those die, a direct replacement often doesn’t exist. We source compatible retrofit boards and add current UL 325 entrapment protection where the old system never had it.
- Pillar-mounted operator failures. When a gate is hung on brick or stone pillars, frost movement in the pillar itself bends the operator mount. Homeowners think the motor is dead. More often, the operator arm is bound against a shifted post or pillar face, and the fix is mechanical, not electronic.
Pricing for Gate Parts & Welding in Westwood, MA
Here are honest ranges for the work we do in Westwood. Hinge replacement runs $340 to $880. Post replacement runs $900 to $2,400 depending on excavation depth and masonry anchoring. Rail repair runs $280 to $650. Custom welding starts around $180 for small latch or bracket work and climbs to $3,000 or more for full frame rebuilds. Every job gets a written price before we start, and that price does not change at the door. If you have a written estimate from another company, we’ll give you a free second opinion. There’s no trip charge inside the county, and seniors and veterans get a permanent 10% discount. Call (877) 610-2993 and we’ll schedule a time that works. If it’s an emergency call, a live person answers around the clock.
We Also Serve Cities Near Westwood
If you’re on the edge of Westwood near Route 1 or 109, we cover Gate Parts & Welding in Westwood and the surrounding area, including Norwood, Dedham, Needham, and Canton. Call (877) 610-2993 and tell us which town you’re in. The truck rolls from our Boston office and reaches you as quickly as traffic allows.
Serving Westwood, MA - Our Local Coverage Area
We’re based in the Westwood area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Westwood
Because Westwood’s frost line sits at about 48 inches, and any gate post set shallower than that heaves upward during freeze-thaw cycling. The post moves, the gate’s swing geometry changes, and the operator starts fighting a misaligned track or rack. The Westwood Gate Motor & Opener is rarely the problem. We excavate, set the post to full depth, and weld the hinges back into true. Call (877) 610-2993 and we’ll check your post depth before recommending anything else.
Sometimes, but only if the post itself is still plumb and sound. If the post is heaving or the base is rotted or cracked, welding the panel just masks the problem for a season or two. Fix the panel without the post and you’ll fix it twice. We’ll check the post with a level before we weld anything. Estimates are free.
No. Many legacy Linear, FAAC, and DoorKing boards are discontinued, but retrofit boards and aftermarket control panels exist that fit the old enclosure and work with the existing motor. We also add Gate Access Control - Westwood with modern UL 325 entrapment photocells at the same time, which most 1980s gates never had. We’ll tell you honestly if retrofitting is cheaper than replacing the operator. Call (877) 610-2993 for a straight answer and a written price.
Westwood’s long private approaches mean more de-icing and plowing, and the salt spray settles directly on the lower hinge barrels. Norwood’s tighter lots and shorter driveways expose gates to less of it. Your hinges aren’t lower quality; they’re taking more salt. We replace rusted barrels with sealed or greasable hinges that hold up better, and we weld them on site.
Massachusetts follows UL 325, which requires entrapment protection devices like photo-eyes or contact edges on automated gates. If your gate predates that standard, you’re not required to rip it out, but any time we service the operator we bring the safety devices up to current code. It’s the right thing to do, and it’s part of every operator repair we quote. Call (877) 610-2993 to schedule a safety check.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Westwood and Norfolk County since 2001.
Ready to get your gate working right? Call (877) 610-2993 now. A live person answers, we’ll give you a straight price before any work starts, and the 90-Day Done Right Promise is stamped on every job.