Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across West Gate
Gate parts and welding in West Gate usually comes down to one question: can the hinge post be saved, or does it need to be cut out and reset in fresh concrete? Most of the time we can save it. A typical hinge replacement on a West Gate swing gate runs $180-$340, and a post reset with new footings runs $450-$850 depending on how deep the rot goes. Salt air from the Atlantic works on gate hardware faster here than people expect, and we’ve been repairing, welding, and rebuilding gates in the 33409 corridor long enough to know exactly where they fail first. Call (877) 610-2993 and we’ll give you a straight answer and a written price before any work starts.
Why Gatewood Fence & Gate Is West Gate’s Preferred Gate Parts & Welding Company
Hal Gatewood started this company in 2001, and he still shows up to look at the gate himself. That matters in West Gate, where a lot of the homes along the 33409 corridor were built in the 1960s and 1970s, and their gates have been through forty or fifty hurricane seasons. For Gate Installation in West Gate, that history matters. We know what Palm Beach County code requires, we know what the county inspector in Mangonia Park will flag on a footing or an entrapment sensor, and we don’t guess.
Our West Gate customers tend to call us after another company already told them the gate can’t be fixed and needs a full replacement. More than half the time, the gate can be fixed. We weld on site, in your driveway, so the gate never leaves your property. Every job carries our 90-Day Done Right Promise in writing. If it’s not right, Hal comes back and makes it right. No runaround, no dispatch queue, no voicemail. A live person answers the phone 24/7.
We’re licensed and insured, background-checked, and we service Viking, Ghost Controls, DoorKing, and Elite equipment, along with LiftMaster, FAAC, BFT, Linear, and Mighty Mule. If you have a gate that sags, binds, or won’t close, call us and get a real answer.
Our Gate Parts & Welding Services in West Gate
Hinge Replacement
Hinges are where salt air hits hardest in West Gate. The prevailing southeast winds carry salt over the few miles from the Atlantic, and uncoated steel hinges on older gates pit and corrode until the top hinge tears loose. We replace hinges with marine-grade stainless or galvanized steel, and we check the post while we’re at it. A new hinge on a rotted post is a wasted trip. Typical hinge replacement in West Gate: $180-$340, depending on gate weight and post condition.
Post Replacement
A gate sags in the hinge post, not in the middle. In West Gate’s 1960s-era homes, many original ornamental iron gates were set on bare steel posts with no corrosion coating at the soil line. Decades of Palm Beach County humidity and standing water from summer rains eat through the post below grade. We dig out the old footing, set a galvanized post with stainless fixings, and pour new concrete to county code. Post replacement in West Gate runs $450-$850, and we pull the permit through the county building division so you don’t have to.
Rail Repair
Slide gates in West Gate’s 1980s and 1990s apartment complexes and single-family homes often have steel rails that have been pitted by salt and standing water. When a slide gate jumps teeth or binds mid-travel, the rail is usually the culprit. We straighten, weld, and reinforce rails on site, and we check the operator’s rack and pinion alignment before we finish. Most rail repairs in West Gate run $220-$480.
Custom Welding
When a gate frame cracks, an operator arm bends, or a panel tears loose, we weld it back stronger than it was. We weld aluminum, steel, and ornamental iron on site. For West Gate’s coastal conditions, we use galvanized or stainless fill material so the repair outlasts the original metal. Custom welding repairs in West Gate typically run $150-$400 per repair point, and we’ll give you a written quote before striking an arc.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in West Gate
We’re certified to work on DoorKing, Elite, Viking, and Ghost Controls, along with the other major gate brands. For West Gate customers, we keep common hinge sets, latch hardware, roller wheels, and operator boards ready so we’re not waiting a week on a parts shipment. If your West Gate Gate Motor & Opener is fried or your Ghost Controls board is throwing fault codes after a storm, we can usually get to West Gate the same day. Boat rack and pinion sets, stainless bolts, marine-grade coatings: we bring the right hardware for the coast, not whatever’s on the truck.
Common Gate Parts & Welding Problems We See in West Gate Homes
- Salt-pitted hinge posts tearing free. The uncoated steel post at the top hinge rusts until the weld breaks and the gate panel drops. Sag correction alone won’t hold if the post footing is compromised.
- Standing water in buried operator pits. West Gate’s June-September rainy season drives water into below-grade operator housings. Loop detector wiring wicks that moisture into LiftMaster and Viking boards, and the board fails.
- Corroded ornamental iron latches and hinges. Original 1960s iron gates in West Gate never had a marine coating. Latch and hinge hardware corrodes until the gate jams mid-travel and bends the operator arm.
- Slide gate rail pitting. Salt pitting on the rail surface makes the rack and pinion jump teeth, especially in the afternoon heat when the metal expands. The fix is a rail repair or replacement, not a new motor.
Pricing for Gate Parts & Welding in West Gate, FL
Here’s what we charge in the 33409 corridor. Hinge replacement: $180-$340. Post replacement: $450-$850. Rail repair: $220-$480. Custom welding: $150-$400 per repair point. Latch and lock replacement: $95-$220. Gate rollers: $120-$260 per set. What moves the number is post condition, gate weight, and whether the county inspector needs to sign off on the footing. You get the price in writing before we touch the gate. No trip charge inside the county, and we’ll knock $40 off any repair over $200. Seniors and veterans always save 10%. Call (877) 610-2993 for a free estimate.
We Also Serve Cities Near West Gate
Our Gate Parts & Welding team works all around the Palm Beach County coast. If you’re in West Gate, West Palm Beach, Palm Beach, Riviera Beach, or Palm Springs, we’ll come out, look at the gate, and give you an honest price. Same crew, same guarantee, same owner behind the work.
Serving West Gate, FL - Our Local Coverage Area
We’re based in the West Gate area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in West Gate
Because West Gate sits in unincorporated Palm Beach County, so gate repair permits are pulled through the county Building Division in Mangonia Park. That’s a separate queue from West Palm Beach city inspections, and it can add a day or two to a job that crosses into 33409. Contractors who mostly work city limits often misprice that turnaround. We plan for it from the first phone call. Call (877) 610-2993 and we’ll tell you exactly what the county will require.
Yes. We prep the galvanized surface, weld with the right filler, and apply a zinc-rich cold galvanizing compound over every weld. That puts the protection back after the heat. Done properly, a galvanized post with stainless fixings will outlast the original bare steel by decades in West Gate’s salt air.
Usually it’s both. Standing water in the buried operator pit corrodes the board connections, and the rail has probably pitted enough to bind the rack and pinion. We dry out the pit, repair or replace the damaged board wiring, and weld or replace the rail so the gate runs clean. Most of these jobs in West Gate run $350-$700. Call (877) 610-2993 and we’ll diagnose it over the phone before we even come out.
The right fix is almost always a post replacement, not just a hinge adjustment. A gate sags in the hinge post, not in the middle. On 1960s West Gate homes, the original post footings are usually rotted below grade from six decades of humidity and rain. We cut out the old post, set a galvanized replacement in fresh concrete to Palm Beach County code, and rehang the gate with stainless hinges. That fix runs $450-$850 and it holds.
It can. If we’re welding or replacing an operator arm on a slide or swing gate in West Gate, the county inspector may require the existing entrapment sensors, safety edges, and photo eyes to meet current standards before signing off. We’ll tell you upfront whether your gate needs the update and include it in the written quote. No surprises at the door. Call (877) 610-2993 to get a clear price.
In a 1980s subdivision off the 33409 corridor, our crew found a Viking slide gate rail so salt-pitted the rack and pinion jumped teeth every afternoon. We cut out the rotted post footing, welded a galvanized steel post with stainless fixings, and set a fresh rail so the Gate Access Control in West Gate cleared without faults. The county inspector signed off on the second trip. That’s the difference between patching a symptom and fixing what the coast does to a gate.
If your gate is binding, sagging, or throwing fault codes, don’t wait until it fails completely. Call (877) 610-2993 for a free estimate. We’ll give you a written price before any work starts, and the 90-Day Done Right Promise is stamped on every job. The name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving West Gate since 2001.