Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Wedgefield
A sagging horse-gate off a lime-rock driveway in Wedgefield usually isn’t a hinge problem. It’s a post problem. The sandy, hydric soil around the Econlockhatchee River corridor holds water against gate posts through every summer storm cycle, rotting them at ground level or heaving them out of plumb until the whole gate binds. Gatewood Fence & Gate fixes this at the source: we cut out the bad post, set a new one in a deeper concrete footing, weld the hinge back square, and re-level the gate so your automatic opener stops fighting itself. Hal Gatewood has been doing this since 2001, and the phone rings to a live person any hour you call: (877) 610-2993.
Why Gatewood Fence & Gate Is Wedgefield’s Preferred Gate Parts & Welding Company
Wedgefield isn’t a suburb. It’s one of Orange County’s last rural-equestrian communities, with 1-to-5-acre ranch lots, horse trailer entrances, and long private drives that most gate companies never see. We see them weekly. The crew that shows up at your place knows a 16-foot pipe swing gate takes a different hinge than ornamental iron, that your opener might be solar because no power line runs to the road, and that a gate post set without addressing drainage will heave again by next spring. Our Gate Parts & Welding work is done on site, in your driveway, not hauled to some shop across the county.
Customers around Wedgefield’s 32833 ZIP, from the ranch roads off 13th Avenue to the larger acreage heading east toward the St. Johns floodplain, call us for the same reason: they want a name they can verify, not a faceless outfit that quotes one price and charges another. Hal’s name is on the shop and on every invoice. Scheduling for Wedgefield work is coordinated from our South Florida office, but the person who shows up knows the local ground conditions. Every job carries the 90-Day Done Right Promise in writing. If it’s not right, one call brings us back. No runaround.
We also stand behind the price. It’s quoted and agreed before any work starts. That’s not a courtesy; it’s how Hal has run jobs since before half the gate companies in this county existed.
Our Gate Parts & Welding Services in Wedgefield
Most gate work in Wedgefield falls into four categories. Here’s what each looks like on your property, and how we handle it.
Hinge Replacement
Heavy pipe gates on Wedgefield horse ranches put tremendous load on hinges, especially when the post has started to rot or lean. We replace worn or seized hinges with heavy-duty weld-on or bolt-on hardware sized for wide agricultural gates, not the light residential hinges a catalog warehouse will sell you. If the hinge tore out of the post, we repair the post, not just the hinge, because fixing the panel without the post means fixing it twice.
Post Replacement
This is the most common call we run in Wedgefield. Standing water after summer thunderstorms sits against wooden gate posts, rots them at ground level, and down comes the gate. We cut out the failed post, set a new pressure-treated or steel post in a deeper footing, and pack the base so water drains away rather than pooling. Then we hang the gate back level and re-align the opener. A gate sags in the hinge post, not in the middle, and that’s where we start.
Rail Repair
Ranch gates take abuse from trailers, livestock, and weather. Bent or broken rails, cracked welds on pipe gates, sagging top rails on wood gates. We straighten what’s salvageable and replace what isn’t, welding cracked joints rather than swapping the whole gate. Our repair-first approach means the gate stays on your Wedgefield property and you don’t pay for a replacement you didn’t need.
Custom Welding
Need a gate widened for a horse trailer? An extension welded onto a pipe gate to span a wider drive? A custom bracket for a solar panel mount or a latch reinforcement on a cattle gate? We do on-site welding for all of it. Hal has been welding gates since 2001 and will cut, fit, and burn it in while the gate hangs in place so the alignment stays true.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Wedgefield
Most Wedgefield automatic gates run one of a handful of operator brands, and we service them all. That includes FAAC swing gate operators common on rural acreage, Linear openers on older slide gates, BFT motors on newer residential installs, and Viking systems on heavy commercial-style gates. We keep common replacement parts on the truck: limit switches, control boards, remote receivers, photo eye sensors, and solar charge regulators for off-grid lots. If we don’t have it, we source it locally and get back to your Wedgefield property quickly rather than making you wait on a freight shipment.
Common Gate Parts & Welding Problems We See in Wedgefield Homes
After years of running calls across Wedgefield’s ranch properties, these are the failures we see over and over.
- Gate posts rotting at ground level. The high moisture near the Econlockhatchee wetlands and regular standing water after summer storms eats wooden posts where they enter the soil. The gate sags, the opener binds, and eventually the post snaps.
- Solar opener charge controllers corroding. Many Wedgefield ranches run solar-powered gate openers because no electrical service reaches the road frontage. Florida humidity and sun exposure corrode the charge controller, batteries die, and the gate won’t open when you’re sitting at the road with a trailer.
- Slide gates jumping the track. When gate posts heave in sandy, hydric soil, the rack and pinion on a slide gate shifts out of alignment. The gate climbs off the track, and the operator grinds itself to death trying to move a gate that’s fighting it.
- Weld failures on ranch pipe gates. Years of opening and closing heavy pipe gates, combined with rust, cause welds to crack at stress points: hinge mounts, latch posts, and mid-rail joints. A cracked weld left alone becomes a broken gate at the worst possible moment.
Pricing for Gate Parts & Welding in Wedgefield, FL
Here’s the honest picture on cost for Wedgefield. Hinge replacement on a standard residential swing gate typically runs $150-$350 per hinge, including labor and the hinge itself. Post replacement, including cutting out the failed post, setting a new one with concrete, and re-hanging the gate, runs $450-$900 depending on post size, depth, and whether we’re dealing with a wooden or steel post. Custom welding work runs $95-$150 per hour, with most small jobs like a crack repair or bracket fabrication finishing in an hour or two. Rail repair on a damaged pipe gate runs $200-$500 depending on how much straightening and welding is needed. Every quote is agreed before any work starts. Call (877) 610-2993 and we’ll walk you through a real price, not a guess. Estimates are free, and if you’ve already got a written estimate from another company, we’ll give you a free second opinion. No trip charge inside the county, and $40 off any repair over $200.
We Also Serve Cities Near Wedgefield
While this page is for Wedgefield, we run the same rural-acreage gate work in the communities around you. That includes Bithlo, Alafaya, Union Park, and Goldenrod. If you’re just outside the Wedgefield line, give us a call and we’ll work out where you fall. Our Wedgefield coverage includes all of 32833 and the ranch roads running east toward the river.
Serving Wedgefield, FL - Our Local Coverage Area
We’re based in the Wedgefield area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Wedgefield
Your gate post is almost certainly moving in the soil. Wedgefield’s sandy, hydric ground expands and shifts as it absorbs water from summer thunderstorms and drainage from the Econlockhatchee floodplain. The post heaves or leans slightly, the gate drops out of square, and your opener has to work harder every cycle until it fails. The fix is a deeper post footing with proper drainage, not just re-hanging the gate. Call (877) 610-2993 and we’ll check your post before it wrecks your opener.
In our experience, it’s usually a corroded charge controller or a bad battery, not the opener motor itself. Florida humidity corrodes charge controller terminals on solar systems, and a dead or weak battery makes the opener act completely dead. We replace the controller, test the panel output, and install a properly sized battery so the system holds a charge through cloudy weeks. If you’re off-grid off 13th Avenue or any road without power, call (877) 610-2993 and we’ll diagnose it on site.
Yes. We do on-site custom welding for wide ranch gates, horse trailer entrances, and equipment access points. We’ll weld the frame, set the hinges, and mount the opener if you need one. Everything is built to handle the daily stress of livestock and trailer traffic, not just a passenger car. Call (877) 610-2993 for a free measure and a written quote.
When the gate posts heave in sandy soil, the rack and pinion on your slide gate shifts out of alignment. The gate starts climbing the track, jumping, or binding, and the operator is getting damaged every time it cycles. We re-set the posts, re-align the track, and replace the rack if it’s worn unevenly. If your gate is jumping, stop running the opener until it’s checked, or you’ll be replacing the motor too. Call (877) 610-2993.
Yes. Any automatic gate needs entrapment protection: photo eyes, reversing edges, or both, depending on the operator and the gate type. It’s required by current safety standards, and it protects children, animals, and anyone walking or riding near the gate. We install and test entrapment protection on every automatic gate job in Wedgefield. If your gate reverses on contact or lacks photo eyes entirely, call (877) 610-2993 and we’ll get it sorted.
Need gate parts or welding in Wedgefield? Call (877) 610-2993 day or night and a live person will answer. We’ll schedule a visit, give you a written quote, and agree on the price before any work starts. Free estimates, no trip charge inside the county, and the 90-Day Done Right Promise on every job.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Wedgefield and surrounding rural communities since 2001.