Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Wayne
Gate parts and on-site welding in Wayne, MI typically run $140 to $680 depending on whether we’re freeing a seized drop rod, replacing a hinge, or resetting a post that the clay heaved out of plumb. Most jobs are done in one visit, with the gate still hanging in your driveway the whole time. Hal Gatewood has been fixing gates since 2001, and the crews serving Wayne live close enough to know that Michigan Avenue salt does things to chain-link hardware that no other weather pattern does. For an exact quote on your gate, call (877) 610-2993 and you’ll get a live person, not a phone tree.
Why Gatewood Fence & Gate Is Wayne’s Preferred Gate Parts & Welding Company
Wayne homeowners tend to recognize the difference between a company that replaces and a company that repairs. Hal Gatewood built the shop on the repair-first idea: if a hinge is worn, we weld a new leaf onto the existing post rather than tearing out the whole gate and starting fresh. That matters in Wayne, where the original 1950s and 60s chain-link gates are still doing their job, just with hardware that’s given up. Fixing the hardware costs a fraction of replacing the gate, and it keeps the look your property has had for five decades. The name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
When a call comes in from a ranch home off Michigan Avenue, the person who answers knows the streets. We don’t punch in a zip code and guess. We know that the post on the west side of the driveway near the old streetcar line has been fighting frost heave since before the homeowner was born. That’s the difference between a parts-runner and a gate mechanic who has done this work in Wayne for years. Our Gate Parts & Welding crew shows up in uniform, background-checked, and ready to weld on site. No hauling your gate to some shop across the county.
Our Gate Parts & Welding Services in Wayne
Hinge Replacement
On Wayne’s postwar ranches, the chain-link gate hinge is almost always original. Fifty to seventy years of Michigan freeze-thaw and road-salt exposure leaves the hinge pins mushroomed and the leaf plates rusted thin. We cut off the old hinge, grind the post clean, and weld a new galvanized hinge in place. The gate panel stays where it is. A typical hinge replacement in Wayne runs $90 to $180 per hinge, including the part and the welding labor.
Post Replacement
Wayne County sits on clay that holds water like a sponge and shoves posts out of plumb every spring. We dig out the old footing, reset the post in a deeper hole with a proper concrete collar, and weld the gate hardware back on. Most post replacements in Wayne run $220 to $480 depending on whether we need to cut the panel free and re-hang it. If the post is heaving but not rotted, we can sometimes realign it and weld a brace for under $160. Show me the gate closing on its own and I’ll show you where it’s failing.
Rail Repair
Top rails on chain-link gates near Michigan Avenue take the worst of it. Salt spray from snowplows and passing trucks eats the galvanizing, then the steel. We weld new rail sections in, re-tension the fabric, and replace the tension bands and brace bands that have rusted through. A rail repair with new bands in Wayne typically runs $120 to $260. If the rail is just sagging and the welds are still sound, we can often pull it back into line with a heat-and-set pass and save you the cost of new pipe.
Custom Welding
Wayne has a mix of tight residential lots and acreage edges where gates get wider and heavier. Hal welds on site, whether it’s a cracked gate frame on a 60-year-old chain-link swing or a heavy steel farm gate at the back of a property off Ann Arbor Trail. Custom welding jobs in Wayne start around $150 for a small crack repair and run up to $900 for a full frame rebuild on a wide double gate. The price is quoted and agreed before any work starts. That’s not a courtesy; it’s the rule.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Wayne
We’re certified on the openers Wayne homeowners actually have: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. If a FAAC or BFT operator on a long Wayne driveway is tripping its limit switch, we usually have the control board or capacitor on the truck. No week-long wait for a part to ship from a warehouse. For the solar-powered Linear and Viking operators on acreage gates, we carry spare actuators, radio receivers, and photo eyes local to Wayne. The goal is one trip, done right, with the gate closing behind us as we leave.
Common Gate Parts & Welding Problems We See in Wayne Homes
- Heaved posts every spring. Wayne’s clay-dense soil holds water, freezes, and pushes gate posts out of vertical. We reset and re-weld the post base, then shim the hinges so the gate swings true again. If you ignore it, the latch side eventually binds and the panel racks.
- Seized drop rods near Michigan Avenue. Decades of salt and dirt pack the ground receiver solid. The rod won’t lift, the gate won’t open, and it looks like a broken gate. It’s usually a 20-minute penetrating-oil and rod-extractor job. More on that below.
- Rusted hinge pins that snap without warning. The hinge looks fine until the pin shears and the gate drops onto the post. We replace both hinges when one fails, because the second one has the same amount of rust in it.
- Solar opener faults on long driveways. Wide acreage gates on Wayne’s edges often run on solar because mains power is impractical. The panel’s clean, but the battery’s shot or the rack and pinion stripped after a post cracked. We fix the mechanical problem first, then the electrical one.
Pricing for Gate Parts & Welding in Wayne, MI
Here’s what Wayne homeowners typically pay us, not a regional average pulled from a website. Hinge replacement: $90 to $180 per hinge. Post reset or replacement: $160 to $480 depending on concrete condition and gate weight. Rail repair with new tension bands: $120 to $260. Custom welding: $150 to $900 based on the frame and span. Drop-rod extraction: $75 to $140. Every quote is agreed in writing before the torch comes out. We also take $40 off any repair over $200, and seniors and veterans get 10% off permanently. No trip charge inside Wayne County. Call (877) 610-2993 and we’ll give you a real number over the phone.
We Also Serve Cities Near Wayne
Our crew covers all of Wayne and the surrounding towns: Westland, Inkster, Romulus, and Canton. If you live off Ann Arbor Trail or near the Canton line, we’ll get your gate sorted like we did for the folks in Wayne. Same phone, same promise, same Hal.
Serving Wayne, MI - Our Local Coverage Area
We’re based in the Wayne area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Wayne
Wayne sits on clay-heavy soil that holds water, and Michigan delivers 30 to 40 freeze-thaw cycles a winter. The water in the ground freezes, expands, and pushes the post out of vertical. It doesn’t matter how light your gate is, the post is being moved by the ground itself. We reset the post in a deeper footing with a proper concrete collar, and it stays put through the next freeze cycle. Call (877) 610-2993 for a free post inspection before it gets worse.
The gate is almost certainly fine. Drop-rod receivers on the original 1950s chain-link gates near Michigan Avenue get packed with decades of road salt, dirt, and rust. The rod seizes in the sleeve, and the gate won’t swing. We free the pin with penetrating oil and a rod extractor, then replace the sleeve if it’s cracked. Last week our techs rolled out to a ranch home just off the old streetcar line, found a 60-year-old swing gate with the drop rod seized solid, freed the pin, replaced the corroded hinges, and reset the latch post. The homeowner assumed the gate was shot. The solar opener on the same entrance was still fine once the friction was gone. $75 to $140, not a gate replacement. Call (877) 610-2993 to get on the schedule.
Yes. We weld on site, in your driveway or at the gate itself. For wide farm gates on Wayne’s acreage edges, we cut out the cracked or rusted sections of the frame, weld in new steel, and re-hang the panel on the existing posts when the posts are still sound. If the post footing is cracked from the extra span, we’ll tell you before we weld anything. The price is quoted and agreed before any work starts. Call (877) 610-2993 and Hal will look at it himself.
Your gate is likely binding, and the motor is drawing too much current trying to push it. On long Wayne driveways, the usual culprits are a post that’s heaved out of line, a seized hinge, or a drop rod dragging in its sleeve. The solar panel charges the battery fine, but the LiftMaster trips because the gate is fighting itself. We fix the mechanical bind first, then test the operator. That order saves you a service call later. Call (877) 610-2993.
Any rust that has eaten through the galvanizing and exposed the steel layer is too much. If you can flake the rust off with a screwdriver, the hinge pin is next. A 1960s hinge in Wayne has survived 60 winters of salt spray and freeze-thaw. Both hinges get replaced when one fails, because the second one has the same amount of rust in it. We weld new galvanized hinges on site for $90 to $180 per hinge. The gate panel stays in place the whole time. Call (877) 610-2993 for a free estimate.
If your gate in Wayne is sagging, seized, or stripped, call (877) 610-2993. You’ll get Hal or one of his crew on the phone, not a recorded menu. Free estimates, written quotes before any work starts, and the 90-Day Done Right Promise on every job.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Wayne since 2001.