Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Thornton
Gate parts and welding in Thornton usually comes down to one question: can you fix what’s there, or do I have to pay for a whole new gate? We fix what’s there. Hal Gatewood has been welding and repairing gates since 2001, and the overwhelming majority of broken gates in Thornton need a hinge pin, a re-welded corner, a re-set post, or a control board – not a tear-out. We serve every neighborhood in the 80241 corridor, from the HOA subdivisions off Eastlake down through the older ranch-style streets in southern Thornton. Call (877) 610-2993 and a live person answers, day or night.
If your gate sags, grinds, or won’t close, we’ll come look at it. Hal is the person who shows up, most days.
Why Gatewood Fence & Gate Is Thornton’s Preferred Gate Parts & Welding Company
We’re a locally owned, owner-operated shop. That means the name on the invoice is the name of the guy standing in your driveway. Hal Gatewood has been repairing gates since 2001, and his published address and license number are right there for anyone to check. Nobody’s hiding behind a national brand or a rented logo.
Thornton homeowners deal with a specific set of problems. The 80241 ZIP is thick with late-1990s and early-2000s tract-built homes, all with HOA-mandated ornamental iron or powder-coated aluminum gates. Those gates are now hitting their first real repair cycle at the same time. Hinge barrels shear, posts heave out of plumb, and the builder-grade operators that came with the house simply give up. We see it every week, and we fix it in the driveway with on-site welding so the gate never leaves your property.
Every job we do carries a 90-Day Done Right Promise in writing. If it’s not done right, one call brings Hal back. No runaround. He’s also the guy who answers the phone at 2 a.m. when your gate is hanging by one hinge after a Chinook. No voicemail, no queue, no call center three states away.
Our Gate Parts & Welding Services in Thornton
When a gate fails in Thornton, it’s almost never the whole gate. It’s one loaded component or one weld that gave out. We replace and repair at the part level, which costs less and keeps the gate looking like it belongs in your HOA’s covenant. Here’s what we do most often in Thornton:
Hinge Replacement
Hinges are the most common failure point on Thornton’s ornamental iron gates. Wind loading from the northwest – Thornton sits fully exposed on the Front Range plains – torques the hinge barrels until the pin shears or the weld cracks. We cut out the old hinge with a plasma torch, weld in a new powder-coated barrel that matches the existing design, and re-hang the gate square. The HOA on your street will not be able to tell the difference, because that’s the point.
Post Replacement
Thornton’s clay soil expands and contracts through every freeze-thaw cycle, and over fifteen or twenty years, that movement pushes hinge posts out of plumb. The gate starts dragging on the latch side and the hinges bind up. We excavate the post footing, dig below frost line, set a new steel post in concrete, and weld the gate back to spec. If the HOA requires a specific post cap or finial, we match it.
Rail Repair
A bent bottom rail or a cracked top rail doesn’t mean the whole gate is scrap. We straighten what can be straightened and cut out and re-weld what can’t. In HOA subdivisions across the 80241 corridor, covenant specs often require exact replacement of ornamental iron profiles. We keep common rail stock in the truck and source custom profiles locally so the repair matches the original design.
Custom Welding
Sometimes what’s there can’t be fixed, and you need a section built from scratch. We do custom welding on site – from gate frames and infill panels to hinge brackets and operator mounting plates. If you’re adding an opener to a manual gate, the mounting plate and the operator post have to be welded correctly or the opener tears itself off within a season. We’ve seen that happen more times than we’d like, usually on someone else’s work.
These are the bread-and-butter jobs of our Gate Parts & Welding service, and they’re the jobs that keep Thornton’s gates swinging true.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Thornton
Most of the automation hardware in Thornton’s master-planned subdivisions was installed as builder-grade equipment, and a lot of it was never upgraded. We carry parts for and service the brands we see most often on those streets: Viking, DoorKing, and Ghost Controls. If your gate has a LiftMaster or FAAC board that keeps burning out after wind reversals, we can swap it for something rated for the abuse Thornton wind dishes out. We don’t stock every part for every brand, but we know exactly what to order and we get it fast for Thornton customers.
Common Gate Parts & Welding Problems We See in Thornton Homes
After two decades of working on gates in this city, the problems repeat. Here’s what we see most in Thornton:
- Sheared hinge pins after Chinook events. Thornton’s open Front Range exposure means northwest winds regularly gust past 50 mph. A gate that’s already carrying stress will lose a hinge pin or crack a weld barrel. After a strong wind advisory, the same subdivision streets will have three or four gates visibly blown open.
- Heaved hinge posts from clay soil. The clay under Thornton’s 80241 corridor expands when wet and contracts when frozen. Over years, that movement pushes posts off plumb. By spring, gates that closed fine in October are dragging and latching crooked.
- Burnout on builder-grade operator boards. The operators installed when the house was built were not spec’d for repeated wind-load reversals. When a 60 mph gust slams a swing gate against its stop, the board struggles, and eventually the board quits.
- Missing conduit runs for automation. A lot of tract construction in Thornton never bothered to lay conduit from the house to the gate. If you want a keypad, loop detector, or intercom added, the wire needs a path. We trench across the HOA strip and run it properly, usually in a day.
In one case, after a 60 mph Chinook event, our crew canvassed the HOA subdivisions off Eastlake in northern Thornton and found three gates on a single street hanging from one hinge. We replaced the sheared hinge pins with powder-coated weld-on barrels, dug new post footings below frost line, and re-hung the swing gates to spec before the HOA’s 72-hour compliance window closed. That’s the kind of call we know to expect in Thornton after a wind event – and we’re already heading there when the phones start ringing.
Pricing for Gate Parts & Welding in Thornton, CO
Here’s the straight answer on cost. A typical hinge replacement in Thornton runs $150 to $350, depending on how many hinges and how much weld time. Post replacement, which means excavating and re-setting a footing, runs $400 to $900 for a standard 6-foot ornamental iron gate. Rail repair or a corner re-weld runs $150 to $400. Custom welding is quoted by the job, but most small fabrication work in Thornton lands between $200 and $800. Adding automation to a manual gate, including the operator, mounting, and any conduit run, typically runs $1,200 to $3,200 depending on the operator and the trenching distance.
Every price gets quoted and agreed to before we start. That’s the deal. We don’t knock on the door at the end with a different number. Estimates are free, and if you have a written estimate from another company, we’ll give you a second opinion on it at no charge. We also offer $40 off any repair over $200, no trip charge inside the county, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 for an exact quote.
We Also Serve Cities Near Thornton
If you’re just outside Thornton, we work in your neighborhood too. We serve Northglenn, Federal Heights, Sherrelwood, and Welby, along with the surrounding unincorporated county. Same crew, same on-site welding, same 90-Day Done Right Promise. Dispatch and scheduling are coordinated from our Denver office, but the people who show up live and work right here in the north metro.
Serving Thornton, CO - Our Local Coverage Area
We’re based in the Thornton area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Thornton
Yes. We match the existing hinge barrel profile and finish, including powder-coated black or bronze ornamental iron hardware common in the 80241 corridor. We’ll take the broken hinge with us or match it from a photo and a measurement, and the replacement is welded on, so there’s no bolt pattern or bracket to give it away. We’ve done this work in HOA subdivisions all over northern Thornton, and we know the compliance process. Call (877) 610-2993 and we’ll tell you exactly what it’ll cost to match yours.
Because the gates in your neighborhood near Eastlake were all installed at roughly the same time, with roughly the same hardware, and they’ve all been taking the same wind. Thornton sits on open plains with no natural windbreak to the northwest, so a strong Chinook hits every gate on the block at the same moment. Hinge pins shear, weld barrels crack, and gates that were already carrying stress fail on the same afternoon. It’s predictable enough that we check those subdivisions the morning after a high-wind advisory.
Yes, usually. We mount the operator so it’s hidden behind or below the gate where the covenant’s sightlines don’t catch it, and we run the conduit underground so there’s no visible wire. Most HOAs in the 80241 corridor care about the gate’s appearance, not the hardware behind it. We’ll tell you what’s possible on your specific gate. Call (877) 610-2993 for a free site look.
It’s usually a combination of frost heave and rail misalignment. The clay under Thornton’s northern subdivisions moves enough through freeze-thaw cycles to push the gate track and support posts slightly out of line, and when the gate rides the rack off-angle, it grinds. We fix it by re-setting the posts and re-aligning the rack, not by greasing over the symptom. Give us a call and we’ll diagnose it in person.
Yes. That’s exactly the kind of repair we prefer. We cut out the bent or cracked section, weld in new matching steel, grind it smooth, and the gate looks original. In most cases it’s a few hundred dollars instead of a few thousand. Call (877) 610-2993 and we’ll give you a price before any work starts.
Call Gatewood Fence & Gate for Gate Parts & Welding in Thornton
If your gate is sagging, grinding, hanging by one hinge, or just refusing to close, call us. Hal Gatewood has been fixing gates since 2001, and he’ll be the one who shows up. We answer the phone live, 24/7, and every job carries the 90-Day Done Right Promise in writing. Call (877) 610-2993 for a free estimate in Thornton, CO, today.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Thornton and the surrounding north metro since 2001.