Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Snellville
If your gate in Snellville is sagging, scraping the driveway, or refusing to open, the problem usually isn’t the part you think it is - many homeowners assume they need Gate Installation in Snellville when it’s really the post underneath. Around here, it’s almost always the post underneath. A hinge replacement in Snellville typically runs $140-$280, and a full post reset with a new concrete footing lands between $450 and $900 depending on soil conditions around the footing. We’ll give you the honest number before any work starts, not after. Call (877) 610-2993 and Hal or one of his crew will walk you through what’s actually failing.
We’ve been fixing gates in Snellville long enough to know that the red clay under this city moves more than the hardware bolted to it. That’s why our Gate Parts & Welding work starts with the post and the footing, not the operator. When the ground shifts, a new hinge just transfers the load somewhere else. We fix the root problem so you’re not calling us again in eight months.
Why Gatewood Fence & Gate Is Snellville’s Preferred Gate Parts & Welding Company
Hal Gatewood started this company in 2001 and his name is still on the shop and every invoice. That matters in Snellville because the people we work for in 30039 and 30078 want to know who’s actually showing up at their driveway. A live person answers our phone 24 hours a day, seven days a week. Not a voicemail, not a call center, not a chatbot. When you call about a gate that won’t close, you talk to a person who has probably fixed the same failure that week.
We’ve worked gates in the subdivisions along Centerville Highway, down toward Lenora Park, and through the older neighborhoods where mid-1990s ironwork is at the end of its service life. Our 90-Day Done Right Promise is in writing on every job. If something isn’t done right, one call brings Hal back. No runaround, no arguing about what was covered. The promise is plain and it’s printed on the invoice.
We serve Snellville with crews that know the local soil, the common gate brands installed in these subdivisions, and the specific ways this climate eats steel hardware, plus how to match the right Snellville Gate Motor & Opener to each setup. Scheduling is coordinated from our Atlanta office, and the crew that shows up at your address is background-checked and uniformed. Hal certifies service on nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule.
Our Gate Parts & Welding Services in Snellville
Post Replacement and Re-Setting
This is the repair Snellville gates actually need most. Georgia’s expansive red clay absorbs water in winter and spring, then contracts through dry late summers. A gate post set in a narrow footing will lean one to two inches, dragging the gate leaf and eventually stripping the operator’s gears. We cut the old footing, set the post plumb in a wider concrete base, and weld or re-hang the gate so it swings true. A post reset on a typical Snellville driveway gate runs $450-$900.
Hinge Replacement
Hinges on 20-to-35-year-old ornamental iron gates in Snellville have spent decades in humid summers and winter ice events. The steel rusts, the fastener holes wallow out, and the gate sags until it drags. We replace hinges with heavier hardware, repair or rebuild the mounting plates, and get the gate back on plane. If the post itself is the problem, we’ll tell you before we quote anything. Hinge replacement in Snellville typically stays in the $140-$280 range per hinge set.
Rail Repair and Custom Welding
When a rail cracks or a weld pops on an older gate, the fix is on-site welding, not hauling the gate back to a shop. Our welders work in your driveway or at your subdivision entrance. That means less downtime and no risk of a gate leaf getting bent in transit. Custom fabrication for cracked rails, broken pickets, or failed operator mounting plates runs from $180 for a simple weld repair up to $700-$1,200 for structural reinforcement on a full-size swing gate.
Gate Rollers, Latches, and Locks
Sliding gates in Snellville see real wear on rollers and track hardware, especially where soil movement has thrown the track out of level. We replace bearings, adjust tracks, and service latches and locks on manual and automated gates. If a latch fails on a pool gate or driveway gate, we treat it as urgent because it is. A roller or latch service call in Snellville starts around $110-$240.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Snellville
Most of the gates we open up in Snellville carry one of a handful of brand names. We stock parts for Linear and Ghost Controls operators that were installed throughout Gwinnett County’s 1990s subdivisions, and we service Viking and DoorKing units just as often. Because Hal has been hands-on with these brands since 2001, we can usually identify the failure from your description over the phone and bring the right part on the first trip. No three-week wait for a control board that a distributor has to special-order.
Common Gate Parts & Welding Problems We See in Snellville Homes
- Leaning hinge posts from expansive clay soil. Snellville’s red clay pushes against shallow footings with enough force to tilt a steel post an inch or more. The gate drags on the latch post, the operator’s limit switches fail, and the customer keeps paying for hinge repairs that don’t address the footing.
- Rusted steel hardware on 1980s and 1990s iron gates. The humid subtropical summer here is rough on exposed steel. Fastener holes corrode, hinge pins seize, and the gate leaf sags under its own weight. Replacing the hinge without fixing the corroded mounting plate is a temporary patch.
- Legacy operator failures tied to modern safety standards. Mid-1990s LiftMaster and DoorKing operators often lack the control board architecture to support contemporary UL 325 entrapment protection. The gate faults repeatedly and shuts down. Sometimes the board can be retrofitted. Sometimes the smarter money is a new operator we install on the same post.
- Ice loading from Snellville’s occasional winter storms. Northeast Gwinnett County gets more ice events than Atlanta proper. During storms like January 2014, ice accumulates on gate arms and operators, cracking boards and stripping gears. We see the damage weeks later, when owners discover the gate won’t run or the leaf has cracked at a rusted hinge.
Here’s the thing we tell Snellville homeowners and HOA board members directly: the red clay moves every year, and the hardware from the 1990s was never built to absorb that movement. Fix the panel without the post and you’ll fix it twice. A gate sags in the hinge post, not in the middle, and that’s where we start.
Pricing for Gate Parts & Welding in Snellville, GA
Here are the numbers we actually quote in Snellville. A hinge replacement runs $140-$280. A latch or roller service call is $110-$240. Re-setting a post in a wider concrete footing lands between $450 and $900. Custom welding starts at $180 and runs up to $1,200 for full structural reinforcement. What pushes a job toward the top of a range is usually what we find underground: a footing that was undersized when the gate went in, or a post so corroded at the base that sistering is the only honest fix.
The price is quoted and agreed before any work starts. Not an estimate, not a starting point. The number Hal writes down is the number on the invoice. We also honor real standing offers: $40 off any repair over $200, no trip charge inside Gwinnett County, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 for a free estimate.
We Also Serve Cities Near Snellville
Our Gate Parts & Welding work regularly takes us into the communities surrounding Snellville, including Lilburn, Lawrenceville, Stone Mountain, and Mountain Park. If you’re in one of those cities and the gate is dragging or the operator quit, the same crew and the same 90-Day Done Right Promise apply.
Serving Snellville, GA - Our Local Coverage Area
We’re based in the Snellville area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Snellville
The hinges were never the root cause. Snellville’s expansive red clay swells through the wet winter and spring and pushes against the hinge post footing. The post tilts, the gate leaf drops, and no new hinge will hold it up. The permanent fix is re-setting or sistering that post in a wider concrete footing, then re-hanging the gate. We can quote that after looking at the footing in person. Call (877) 610-2993.
Usually we can weld a new hinge or a reinforced hinge bracket onto the existing panel without replacing it. The deciding factor is the condition of the steel around the old hinge. If the parent metal is still solid, we grind back the rust, weld on new hardware, and the gate is serviceable for years. If the panel is rusted through in multiple places, replacement is the honest recommendation. We’ll show you the condition before we quote anything.
That depends on the control board revision. Some mid-1990s LiftMaster boards can accept a retrofitted external entrapment protection module. Many cannot, and those units fault repeatedly until they stop running. We’ll assess it on-site and tell you whether a retrofit makes sense or whether a new operator is the cheaper fix over the next three years. Either way the price is quoted before any work begins. Call (877) 610-2993 for a free assessment.
It’s both. In Snellville’s 30078 ZIP code we routinely find subdivision entrance gate posts tilted one to two inches out of plumb from clay soil expansion. Cutting the old footing and setting the post in a wider concrete base is the structural fix. Then we weld or re-hang the gate on that post so the whole assembly is square. A motor replacement alone won’t solve it, and neither will a hinge swap. Call us for a free estimate at (877) 610-2993.
They absolutely do. Northeast Gwinnett County sits in a zone that receives more frequent winter ice events than Atlanta proper. Ice loading on gate arms and operators adds real weight and stress, and events like January 2014 cracked circuit boards and stripped drive gears on gates across Snellville. Rusted hinges snap clean off under that load, dropping the gate leaf onto the driveway. It’s a recurring failure mode we prepare for every winter.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Snellville since 2001.