Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Shaw Heights
Gate parts and welding in Shaw Heights comes down to one fact: most of the gates in this town are 50-plus years old, and the original posts were never meant to survive this many Colorado winters. A typical repair here runs $180 to $340 for hinge replacement and post realignment, and we can usually get to you the same day you call. We know the chain-link and tubular steel gates off Cherokee Street, along Turnpike Drive, and through the 80035 zip code because we have been fixing them for years. When a gate drags across the driveway or a latch stops catching, call (877) 610-2993 and talk to a live person who knows Shaw Heights.
Why Gatewood Fence & Gate Is Shaw Heights’s Preferred Gate Parts & Welding Company
We are not a call center that tells you a gate needs full replacement before anyone lays eyes on it. Hal Gatewood has been at this since 2001, and the name is on the shop. When you call about a sagging gate in Shaw Heights, you’ll talk to someone who understands what 60 mph chinook gusts do to a rail end, and why a hinge post that leaned two inches over the winter will not straighten itself in May.
Customers across Shaw Heights tell us the same thing: they wanted someone who would actually show up and fix the gate, not sell them a new one. The 90-Day Done Right Promise is written on every job. If it is not right, one call brings Hal back. No runaround, no pushback. That promise matters more in Shaw Heights, where most gates are original 1960s and 1970s installations still worth saving with the right parts and a clean weld.
We coordinate scheduling from our Denver office, but the person who shows up at your Shaw Heights driveway is local, background-checked, and equipped with the hinges, posts, and welding gear to do the job on site. No hauling your gate to some shop across town. The fix happens in your driveway, where you can watch if you want to.
Our Gate Parts & Welding Services in Shaw Heights
Hinge Replacement
Hinge replacement in Shaw Heights almost always involves more than swapping a part. Decades of Adams County hard water rust-welds the original hinge bolts to the post, so we use a grinder to cut them free, then weld on new greasable hinges that will not seize up the same way. We set the gate leaf back to level and check the swing path before we pack up. Typical hinge replacement runs $150 to $260 per side, depending on how much cutting the old hardware takes.
Post Replacement
This is the repair we do more than any other in Shaw Heights. The original galvanized posts from the 1950s through 1970s sit in concrete collars that crack and heave with every freeze-thaw cycle. Once a post tilts two inches out of plumb, the gate drags and the hinges bind. We remove the old post, dig out the cracked collar, and pour a new 24-inch concrete footer with rebar reinforcement before setting the new post straight. A full post replacement in Shaw Heights generally runs $320 to $550.
Rail Repair
Chain-link and tubular steel gates across Shaw Heights take a beating from wind. Chinook gusts that exceed 60 mph pull rail ends out of the terminal posts, and once a rail lets go, the gate flaps and the latch misaligns. We cut out the stretched or torn rail section, match the existing galvanized material, and weld it back solid. Expect $120 to $200 for a typical rail repair, less if it is a simple re-seat and re-tension.
Custom Welding
Some Shaw Heights gates need a fix that no catalog part covers. A bent frame brace, a mounting plate that no longer lines up, a hinge that has to be cut and repositioned. That is what our on-site welding is for. We bring the welder to your driveway, and Hal or one of his crew welds the repair in place, then grinds and paints the joint so it looks like it belongs. Custom welding jobs in Shaw Heights typically run $90 to $180 an hour, and most repairs take under two hours.
For a fuller picture of what we handle, see our Gate Parts & Welding service page, which covers the complete scope from parts sourcing to on-site fabrication.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Shaw Heights
We stock parts and service the major gate opener and hardware brands homeowners here actually have: Viking, Ghost Controls, and DoorKing are the ones we see most on Shaw Heights swing gates. If you have an Elite opener on a driveway gate, we carry compatible hardware for those as well. Because we keep common hinges, brackets, and rail hardware on the truck, most Shaw Heights jobs are finished in one visit instead of two or three. Parts are matched to what is already on your gate, not whatever is easiest to order.
Common Gate Parts & Welding Problems We See in Shaw Heights Homes
- Tilted hinge posts from heaved concrete. The original 1960s post footer cracks over decades of freeze-thaw, the post leans an inch or three, and suddenly the gate grinds on the driveway. This is the single most common call we get in Shaw Heights, and the fix is a new plumb post with a rebar-reinforced collar, not a shim.
- Rust-welded hinge bolts. Hard water in Adams County does not just spot the glassware. It corrodes gate hardware until the hinge bolts freeze solid. We cut them out with a grinder and replace with greasable hardware that lasts.
- Rail ends pulled from terminal posts. Chinook wind gusts yank rails loose, the gate loses tension, and the latch stops lining up. Re-welding the rail end and re-setting the tension fixes it for good.
- Drooping gate leaves on original chain-link frames. Fifty-plus-year-old tubular steel fatigues at the hinge side. We weld reinforcement plates or replace the frame section, then re-hang the gate square.
Pricing for Gate Parts & Welding in Shaw Heights, CO
Here is what we actually charge in Shaw Heights, no games. Hinge replacement runs $150 to $260 per side, including cutting out rusted hardware. Post replacement with a new concrete footer runs $320 to $550. Rail repair sits between $120 and $200. Custom welding is $90 to $180 per hour, and most jobs take one to two hours. The price you are quoted before we start is the price you pay. That is not a slogan; it is how we run every job. We also offer $40 off any repair over $200, no trip charge inside the county, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 for a straight answer on your gate.
We Also Serve Cities Near Shaw Heights
Our repair area covers all of Shaw Heights and the surrounding communities: Berkley, Westminster, Federal Heights, and Sherrelwood. If you live just outside town, call anyway. We are likely already heading your direction, and the free estimate policy does not stop at the city line.
Serving Shaw Heights, CO - Our Local Coverage Area
We’re based in the Shaw Heights area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Shaw Heights
Because most of the posts in Shaw Heights are original 1960s and 1970s galvanized steel set in concrete collars that were never deep enough for the Front Range freeze-thaw cycle. Water gets into any small crack, freezes, expands, and pushes the collar up. By March, the post leans and the gate drags. The permanent fix is a new post set in a 24-inch rebar-reinforced footer. Call (877) 610-2993 and we will look at it before it gets worse.
Usually just new hinges and a straightened post. The gate leaf itself is often fine; the hinge post has tilted out of plumb, making the gate ride low. We do not sell you a new gate when the old one can be re-set, re-hung, and welded solid. Call (877) 610-2993 and get a free estimate on the actual fix.
If the existing footing is solid and only the post shifted, we sometimes can re-seat it. But in Shaw Heights, the footing is usually the problem. A cracked 1960s collar will just fail again next winter. We recommend the full fix: new footer, rebar, and a plumb post that will stay put for another few decades. You get the quote before any work starts.
No. It almost never is. When the latch jams after a windstorm, it is because the gate leaf or rail shifted and pulled the latch out of alignment. The latch is just the symptom. We re-align the gate, re-tension the rails, and the latch works again. If you keep adjusting the latch without fixing the alignment, you will adjust it forever. Call (877) 610-2993 and we will find the real problem.
Check whether the gate drags on the driveway, whether the hinge post looks tilted, and whether the latch plate lines up with the catch. Note which side sags. That is all we need to know before we arrive. You do not have to diagnose it; that is our job. Call (877) 610-2993 with what you see, and we will schedule a visit.
Contact Gatewood Fence & Gate in Shaw Heights
If your gate is dragging, leaning, or rattling through every windstorm, call (877) 610-2993. We answer live, 24/7. Hal Gatewood has been fixing gates since 2001, and the 90-Day Done Right Promise means one call brings him back if anything is not right. You get a straight quote before we touch a tool, and the person who shows up at your Shaw Heights home is the person you called, not a stranger from three states away. That is the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Shaw Heights and the surrounding Front Range since 2001.