Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Shadow Hills
Most gate failures in Shadow Hills start the same way: a hinge weld cracks on a heavy pipe ranch gate, a post starts leaning in decomposed granite, or a gate operator arm bends under a Santa Ana gust. We fix all of it on site, usually in one visit. Gatewood Fence & Gate has been doing Gate Parts & Welding work since 2001, and Hal Gatewood answers the phone himself at (877) 610-2993. We serve every ZIP in Shadow Hills, 91040, from La Tuna Canyon Road up to Sunland Boulevard. If your gate is dragging, jammed, or swinging wild, call us and we’ll tell you straight what it needs and what it costs before any work starts.
Why Gatewood Fence & Gate Is Shadow Hills’s Preferred Gate Parts & Welding Company
Shadow Hills is different from the flat subdivisions over in Burbank or La Crescenta-Montrose. Most properties here run on acreage. Long dirt or decomposed granite driveways. Wide pipe gates at the road and heavier paddock gates back by the barn. That means the person working on your gate needs to understand load, soil movement, and wind. Hal has spent decades looking at exactly these failures. A gate sags in the hinge post, not in the middle, and that is where we start.
Every job carries the 90-Day Done Right Promise in writing. If it isn’t done right, one call brings Hal back. No runaround. The name is on the shop, and the shop is down the road. That is the oldest accountability there is.
We answer calls with a live person, 24 hours a day, 7 days a week. Not a voicemail. Not a call center three states away. When a windstorm snaps a hinge weld at 10 p.m. and your horses are out, you need a person, not a recording.
Our Gate Parts & Welding Services in Shadow Hills
We don’t replace what we can repair. A lot of companies want to sell you a whole new gate when the real problem is one cracked weld or a hinge pin that’s worn oval. We weld on site, in your driveway, so the gate stays where it belongs. Here’s what we handle most often for Shadow Hills property owners.
Hinge Replacement
Wide ranch gates put enormous load on hinges, especially in Shadow Hills where 16-foot and 18-foot pipe gates are standard. When Santa Ana winds hit 50 mph, they push the gate past its stop and twist the hinge barrel or shear the weld at the post. We stock heavy-duty barrel hinges and adjustable gate hinges rated for exactly this. We’ll cut the old ones off, weld new ones on, and set the gate so it swings true with no sag.
Post Replacement
Your gate post sits in decomposed granite that expands in the wet season and settles hard during dry heat cycles. That’s why posts lean. We dig out the old footing - often undersized - and set a deeper post with proper concrete and rebar. Fix the panel without the post and you’ll fix it twice. In Shadow Hills, post work means accounting for the soil, not just swapping a sleeve.
Rail Repair
Rough-sawn wood ranch gates look great until the dry heat cracks a rail and the gate starts to drop. We repair split rails, re-square the frame, and weld steel corner brackets where the old fasteners have pulled loose. If the gate is steel pipe, we cut out the bent or cracked section and weld in new pipe, then re-paint so the repair blends.
Custom Welding
Not every gate comes off a shelf. Horse paddock gates, hay barn doors, custom entrance gates - we weld them to fit your posts, your hinges, and your land. We do MIG and stick welding on site, and we build gates that hold up to livestock leaning on them. If you’ve got a bent gate or a broken latch mount, we’ll weld it stronger than the original.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Shadow Hills
We’re certified to service nine major gate brands, including DoorKing, Viking, and Ghost Controls. Those are the operators we see most often on Shadow Hills properties because they make solar-capable and heavy-duty models sized for wide gates. We keep common parts on the truck - hinges, limit switches, gear racks, receiver boards - so a trip to your place usually ends with the gate working again, not with “parts are on order.”
Common Gate Parts & Welding Problems We See in Shadow Hills Homes
- Santa Ana wind damage. The Verdugo Mountains funnel wind straight into Shadow Hills. We regularly see hinge welds snapped clean through and operator arms bent back against the post after a bad gust night. If your gate is making a popping sound when you open it, the weld is already failing.
- Posts leaning from seasonal soil movement. Decomposed granite holds water in March and contracts hard by August. A post that looked fine in the spring can be leaning six inches by late summer, dragging the gate across the ground. This is the single most common structural problem we fix in Shadow Hills.
- Dust and grit in slide gate tracks. Unpaved driveways kick fine dust into roller tracks and gear racks. That grit wears rack and pinion teeth and seizes rollers, leaving a slide gate that binds halfway open. It’s not a motor problem - it’s an environment problem.
- Cracked wooden ranch gate rails. The extreme dry-heat cycles between Santa Ana events and summer crack rough-sawn cedar and oak boards. Hardware loosens as the wood shrinks, and the gate starts to rack and drag. We re-square the frame and re-tighten or replace the hardware before the gate tears itself apart.
Pricing for Gate Parts & Welding in Shadow Hills, CA
A typical hinge replacement on a standard ranch gate in Shadow Hills runs $180-$320, including cutting out the old hinge and welding the new one. A full post replacement with new concrete footing runs $450-$850 depending on depth and gate width. Custom welding jobs - say, re-welding a cracked frame or building a paddock gate - run $150-$400 for most repairs, and $600-$1,800 for a new custom gate depending on size and material. Rail repair usually lands between $150 and $400. We quote every job before work starts, in writing, and that price doesn’t change at the door. There’s no trip charge inside the county, and any repair over $200 gets $40 off. Seniors and veterans get a permanent 10% discount on everything. Call (877) 610-2993 and Hal will give you a straight number.
We Also Serve Cities Near Shadow Hills
We work all around the foothill communities near Shadow Hills, including Sunland, Tujunga, La Crescenta-Montrose, and into Burbank. Same crew, same 90-Day Done Right Promise, same on-site welding. If your property is just over the line, call us anyway - we’re probably already in the area.
Serving Shadow Hills, CA - Our Local Coverage Area
We’re based in the Shadow Hills area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Shadow Hills
Because the problem is under the ground, not above it. Your post sits in decomposed granite that swells with winter moisture and settles in summer. If you just push the post back and pack dirt around it, it’ll lean again by August. The fix is a deeper concrete footing with rebar, sized for the gate’s weight and Shadow Hills soil conditions. Call (877) 610-2993 and we’ll look at the footing and tell you what’s actually happening down there.
Yes, if you size the opener and the panel right. A 16-foot pipe gate needs a heavier operator and a solar panel with enough wattage to keep the battery topped up between uses. We install solar openers with battery backup on Shadow Hills properties all the time - and because this is a High Fire Hazard Severity Zone, the battery backup also keeps the fail-safe open working during a power outage. That’s the part generic opener installs miss.
You can have both. Shadow Hills fire-access code requires the gate to fail-safe open on power loss, but we install systems with battery backup and a controlled-open sequence so the gate opens at a controlled speed instead of swinging loose. We also install Knox box provisions so fire crews can unlock the gate manually. Call (877) 610-2993 and we’ll walk through a setup that meets code and keeps your livestock where they belong.
Yes. We weld on site, in your driveway, so there’s no hauling the gate to a shop. We’ll cut out the cracked weld, re-weld the hinge with proper penetration, and add a gusset plate if the design calls for it. You’re usually opening and closing the gate again the same day. Call (877) 610-2993 for a free estimate - we’ll tell you the price before we touch a torch.
No. The summer sag comes from two things: cracked or shrinking wood and hardware that’s worked loose during the wet-dry cycle. We’ll re-square the frame, replace any split rails, and weld on steel corner brackets so the gate holds its shape. Then we’ll check the hinges and the post. If the post is moving, we address that too. You don’t learn to live with a dragging gate - you fix it once. Call (877) 610-2993 and we’ll come out and have a look.
We rebuilt a twisted hinge post on a 16-foot pipe ranch gate off McBroom Street after Santa Ana winds pushed the gate past its stop and sheared the weld. We set a deeper post footing in the decomposed granite, re-hung the gate with new heavy-duty hinges, and added a solar gate opener with battery backup so the owners could keep livestock in and still meet fire-access fail-safe requirements. That’s the kind of job we do all over Shadow Hills.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Shadow Hills since 2001.