Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across San Pablo
Gate parts and welding in San Pablo usually means one of three things: a hinge post that has rusted through at the footing, a swing gate that sags because the ground has heaved, or a weld that finally let go after years of salt air working on it. We fix all three, and we do most of it on site in your driveway. No hauling your gate to a shop. No swapping parts that don’t need swapping. If you’re in the 94806 ZIP code and your gate binds, droops, or won’t latch square, call (877) 610-2993 and you’ll get a live person. Hal Gatewood has been doing this since 2001, and the name on the shop is the same name on every invoice.
Why Gatewood Fence & Gate Is San Pablo’s Preferred Gate Parts & Welding Company
Most of the gates we work on in San Pablo were installed in the 1970s, 80s, and 90s as security deterrents along the San Pablo Avenue corridor and the side streets branching off it. That means we’re not looking at fresh steel that just needs a small adjustment. We’re looking at decades of deferred maintenance, rust hidden inside hinge barrels, and posts that have been slowly rotting at the concrete line. The person who shows up is either Hal himself or someone from his crew who has been doing this long enough to know what a San Pablo gate looks like when the soil has shifted and the salt air has done its work.
San Pablo customers call us because we answer the phone around the clock, we quote a price before any work starts, and we stand behind every job with our 90-Day Done Right Promise in writing. If it’s not done right, one call brings us back. No runaround. The shop is local, the license is published, and Hal’s address is on every invoice. That’s the kind of accountability people in San Pablo tell us they’ve been looking for after getting burned by a company that quoted one price on the phone and charged another at the door.
Response time to San Pablo is measured in hours, not days. When a security gate won’t close at a rental duplex off Rumrill Boulevard, the landlord can’t wait a week. We get it. That’s why we prioritize San Pablo calls the same way we prioritize a widow whose driveway gate is the only thing between her house and the street. Our Gate Parts & Welding team carries common hinge pins, latch hardware, and welding equipment on every truck, so most repairs happen in one visit.
Our Gate Parts & Welding Services in San Pablo
Here’s what we actually do in San Pablo, week in and week out. This is the work that keeps older security gates swinging clean instead of dragging through the concrete.
Hinge Replacement
Salt air from San Pablo Bay is hard on hinge pins. We see galvanized steel pins that look fine on the outside but are corroded solid inside the barrel, which is why the gate binds or squeals even when the panel itself looks straight. In San Pablo, hinge replacement usually means cutting out the old welded barrel, fitting a new stainless or heavy-gauge galvanized pin, and re-welding the assembly so the gate swings free. A typical hinge replacement in San Pablo runs $180 to $420 depending on the gate weight and whether both hinges need to be done.
Post Replacement
San Pablo has a problem that inland cities don’t: winter rain soaks the clay-heavy soil, the soil heaves, and gate posts shift. Once a post moves even half an inch, the gate sags and the latch stops lining up. You can adjust the hinges, but you’ll be adjusting them again next season. Fix the panel without the post and you’ll fix it twice. Post replacement in San Pablo typically means digging out the old footing, setting a new post in concrete at the correct depth, and re-welding the hinge assemblies. A standard residential post replacement runs $350 to $750, more if the post is in a wall or has to be matched to existing masonry.
Rail Repair
Wrought iron gates from the 1970s were usually welded at the rail-to-frame joints, and those welds are the first thing to fail after decades of rust and wind loading. On San Pablo rental properties where the gate gets used dozens of times a day, a cracked rail weld eventually becomes a snapped rail. We grind out the old weld, fit the rail back to true, and re-weld on site. Rail repair in San Pablo typically runs $150 to $350 for a single cracked joint. It’s faster and cheaper than a full gate replacement, and when the weld is done right on a clean surface, it holds.
Custom Welding
Sometimes the part you need doesn’t exist off the shelf. A 1950s duplex gate with a rusted-through latch post often has non-standard rail spacing or a custom drop rod that no supplier stocks. That’s when custom welding pays for itself. We fabricate replacement rails, rebuild latch post sleeves, weld in new pickets, and reinforce cracked frames. Custom welding in San Pablo is quoted by the job after Hal sees the gate, with most small fabrication work running $200 to $600. A full custom gate frame is bigger money and gets a written quote before any torch touches steel.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in San Pablo
We service gate operators and hardware from Viking, Ghost Controls, and DoorKing, among others. The older operators on San Pablo rental properties are often Viking or DoorKing units that have been outside for fifteen years in salt air, and we stock the replacement boards, safety photocells, and limit switches those units eat through. We also carry the stainless hinge pins and galvanized latch hardware that Ghost Controls systems in the 94806 area commonly need. If we don’t have the part on the truck, we can usually have it for the next day and finish the job without making you wait a week.
Common Gate Parts & Welding Problems We See in San Pablo Homes
- Hinge pins corroding from the inside out. The barrel looks fine, but the pin has rusted solid inside and the gate has to be forced. We see this on gates within half a mile of San Pablo Bay far more often than in Richmond or El Sobrante.
- Post shift from winter soil heaving. The ground in San Pablo holds water through the rainy season, swells, and moves that water-logged soil against the footing. A post that was plumb in September is off by half an inch in February.
- Rust-through at the concrete footing. That’s the classic failure on 1950s and 1960s rental duplex gates along San Pablo Avenue. The post rots right where it meets the concrete, and now you need post replacement plus re-welding the hinges and latch assembly back into position.
- Rusted latch hardware that won’t hold square. Gate latches in San Pablo take a beating from wind off the Bay. When the strike plate rusts or the latch bar bends, the gate won’t close properly, and a security gate that won’t close is basically a decoration.
Pricing for Gate Parts & Welding in San Pablo, CA
A typical hinge replacement in San Pablo runs $180 to $420. Post replacement usually lands between $350 and $750 for a standard residential post. Rail repair runs $150 to $350 per joint, and small custom welding jobs fall in the $200 to $600 range. Those are honest ranges for this market, quoted before any work starts. The price we give you on the phone is the price you’ll see on the invoice. People in San Pablo have told us too many stories about national companies that quoted low and billed high, and that’s not how Hal does business. We also keep standing offers that don’t require haggling: $40 off any repair over $200, no trip charge inside the county, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 and get a real number. You’ll know the price before we touch the gate.
We Also Serve Cities Near San Pablo
If your gate is in El Sobrante, Richmond, Pinole, or Tara Hills, we work those neighborhoods too. Same crew, same written pricing, same 90-Day Done Right Promise. We’re based out of the San Francisco Bay Area and serve San Pablo as our local crew, but the truck rolls anywhere in the East Bay when the job needs it.
Serving San Pablo, CA - Our Local Coverage Area
We’re based in the San Pablo area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in San Pablo
Because the hinge pin is the part you can’t see. Salt-laden marine air from San Pablo Bay gets inside the hinge barrel and corrodes the pin from the inside out, even on galvanized steel. The panel looks straight, but the hinge has turned into a rusty brake. Hinge replacement in San Pablo typically runs $180 to $420. Call (877) 610-2993 and we’ll tell you if it’s the hinge or something else, free.
The sag isn’t in the middle of the gate; it’s at the post. Winter rain in San Pablo saturates the clay-heavy soil, which heaves and shifts against the footing, moving the post out of plumb. You can adjust the hinges to compensate, but the post will keep moving every wet season. We see this constantly on the pre-1980 construction around town. Post replacement runs $350 to $750, and the price is locked before any work starts. Call us at (877) 610-2993 and we’ll pull up and look at the footing.
Galvanized, every time. A painted steel post near San Pablo Bay starts rusting at the weld points and the concrete line within a few years, because the salt air gets under the paint wherever there’s a scratch or a pinhole. Galvanized steel has a zinc coating that sacrifices itself to the salt air, so the steel underneath holds for 15 to 20 years even a few miles inland from the Bay. The paint is cosmetic. The galvanizing is what actually survives.
Salt air is corrosive to the thin wire contacts and plastic housings on safety photocells, and the exposure near San Pablo Bay accelerates that failure. We see Viking and DoorKing operators in the 94806 ZIP code where the motor and board are fine, but the photocells have clouded over and the gate won’t close automatically. Photocell replacement usually runs $120 to $250 per set, and we stock them for the brands we service. Call (877) 610-2993 and we’ll bring the part.
Yes, and we do it regularly. The post rusts at the concrete footing, but the gate panel and rails are often still solid. We cut out the rotted section, set a new post or sleeve, re-weld the hinge and latch assemblies, and the gate swings clean and locks square. On a 1950s duplex just off San Pablo Avenue, our crew replaced a rusted-through hinge post and re-welded the frame after soil heaving from winter rain threw the latch out of alignment. The landlord had deferred it for years, but the job took one visit. The gate still works. That’s the whole point.
Call for a Free Estimate on Gate Parts & Welding in San Pablo
If your gate is sagging, sticking, or rusting through at the post, call (877) 610-2993. We’ll give you a straight answer and a straight price for San Pablo work, quoted before any cutting or welding starts. No trip charge inside the county. Seniors and veterans get 10% off, permanently. And every job carries the 90-Day Done Right Promise in writing. Hal’s name is on the shop and on the invoice, and the shop is down the road. That’s the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving San Pablo since 2001.