Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Powder Springs
Most Powder Springs gate problems start underground, in the red clay under your brick columns, long before a hinge or operator shows symptoms. We fix the whole system, not just the part that finally failed. Gatewood Fence & Gate has been locally owned and owner-operated since 2001, and our Gate Parts & Welding crew works Powder Springs driveways and subdivisions every week. Call (877) 610-2993 and a live person answers, day or night.
Why Gatewood Fence & Gate Is Powder Springs’s Preferred Gate Parts & Welding Company
Hal Gatewood started this shop in 2001, and his name is still on the door and on every invoice. Powder Springs homeowners call us because the person who quotes the job is often the same person who shows up with the welder. We publish our address and license number. We do not hide behind a call center or a cute 800-number maze.
Crews roll into Powder Springs neighborhoods like Brownsville Station, Macland Township, and the subdivisions off Dallas Highway and Powder Springs Road with fully stocked trucks. Hinge plates, weld rod, brackets, operators, rollers, and the odd lead anchor for a brick column. When we say we can fix your gate on the first trip, it’s because we already carry what Powder Springs gates actually need.
No trip charge inside Cobb County. Every job gets the 90-Day Done Right Promise in writing. If a weld cracks or a hinge pulls loose again, one call brings us back. No fine print. No “that part isn’t covered.” Hal fixes it.
Our Gate Parts & Welding Services in Powder Springs
Hinge Replacement
Older ornamental iron driveway gates in Powder Springs often hang from hinges that were lag-bolted into brick columns set on shallow concrete pads. Twenty years of Georgia Piedmont clay heave works those lags loose, and the gate starts sagging at the post. We cut out the failed hinge plate, weld in a heavier-gauge replacement, and anchor it so the post, not the bolt, carries the load. Typical Powder Springs hinge replacement including welding runs $140 to $210 per hinge, depending on column condition.
Post Replacement
When a gate post has cracked at the base or thrown the gate out of plumb beyond correction, replacement is the honest fix. We dig out the old footing, set the new post deeper, and backfill so Powder Springs’s swelling clay has less room to move the post year over year. Post replacement typically runs $380 to $650 in Powder Springs, including concrete and re-setting the gate leaf.
Rail Repair
Top and bottom rails on double swing gates take the brunt of every wind storm that rolls through western Cobb County. A cracked rail lets the whole leaf twist, which binds the hinges and strips the operator gear. We weld the crack, add a gusset where needed, and re-square the leaf before it damages the posts. Most rail repairs in Powder Springs run $120 to $260 per leaf.
Custom Welding
Powder Springs has plenty of custom ornamental gates, and we fabricate and weld on site. Pickets, scrolls, hinge ears, sag-correction brackets, motor brackets, and column plates. If the gate leaf is repairable, Hal welds it in your driveway rather than hauling it off and selling you a new one. Custom welding jobs in Powder Springs typically run $90 to $180 per hour plus materials, and you get a written price before the first arc is struck.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Powder Springs
We service and stock parts for Linear, FAAC, BFT, Viking, LiftMaster, and several other major gate brands. Powder Springs has a particular problem with early-generation Linear and LiftMaster operators installed during the 1990s and 2000s subdivision boom. Those boards and limit switches have been discontinued, so we keep crossover kits and have the schematics to do full operator-board swaps when a simple part isn’t made anymore. No “we’ll order it and call you back” runaround.
Common Gate Parts & Welding Problems We See in Powder Springs Homes
- Clay-heaved gate posts throwing gates out of plumb. Powder Springs sits in the Georgia Piedmont red-clay belt. Spring rains swell the clay, summer drought shrinks it, and your brick column footings move a little every year. A gate aligned in May can bind by August.
- Builder-grade operators with undersized wire runs. Many Powder Springs homes built in the late 1990s and 2000s got gate operators wired with 14-gauge residential wire and no conduit between house and gate. Now that the 20-year-old unit is failing, that thin wire can’t carry the current a modern FAAC or LiftMaster opener needs.
- Discontinued community entry gate operators. Subdivisions along Dallas Highway and Powder Springs Road that installed Linear slide operators in the early 2000s are reaching end-of-life cycles all at once. Replacement parts were discontinued a decade ago, so whole communities go down when one board dies.
- Torn hinge plates on brick columns. Swing gates on late-90s and 2000s subdivisions pull the top hinge loose from the brick column as clay heaves the footing. The gate binds, drags, and the operator strips its gear before most homeowners realize the post moved, not the motor.
Pricing for Gate Parts & Welding in Powder Springs, GA
Hinge replacement in Powder Springs runs $140 to $210 per hinge. Post replacement runs $380 to $650. Rail repairs run $120 to $260 per leaf. Custom welding runs $90 to $180 per hour plus materials. A full operator-board swap for a dead community gate operator usually lands between $900 and $1,400 parts and labor, depending on the model and whether a new conduit run is needed.
Those are honest ranges for this market. What moves the price is column condition. A brick column that needs repointing and re-anchoring adds to the job. A clean steel post in good concrete saves money. You get a written price before we start, and that price is what you pay. No surprises at the door. Call (877) 610-2993 for a free estimate.
Note: pricing ranges reflect typical Powder Springs jobs as of early 2026. Your gate gets a specific quote after we see it.
We Also Serve Cities Near Powder Springs
Our gate parts and welding crews cover Powder Springs and the surrounding Cobb County communities. If you’re in Smyrna, Mableton, Fair Oaks, or Kennesaw and dealing with a sagging gate or cracked weld, we’re not far out. We know those neighborhoods too. Learn more about our Powder Springs service area or call (877) 610-2993 and tell us where you are.
Serving Powder Springs, GA - Our Local Coverage Area
We’re based in the Powder Springs area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Powder Springs
Powder Springs sits directly on Georgia Piedmont red clay, and that clay expands when it soaks up spring rain, then contracts during summer dry spells. Your brick gate column sits on a shallow concrete pad, and that pad rides the clay like a raft. When the clay swells, the column heaves up and tilts. The gate binds by late summer. We fix this by stabilizing the post and re-setting the column base, not just re-hanging the gate. Call (877) 610-2993 and we’ll look at your footings.
Yes, that’s most of what we do. Cracked rails, snapped pickets, broken hinge ears. If the leaf has structural steel left to weld to, we weld it on site and re-hang it the same day. We replace the leaf only when it’s rusted through or bent beyond straightening. Hal is a repair-first shop. Get a free estimate at (877) 610-2993.
Many of those early Linear slide operators have been discontinued for a decade. Limit switches, boards, and gear sets simply aren’t manufactured anymore. If we can source a crossover part, we’ll tell you what a repair costs. If not, we’ll quote a full operator swap with a modern unit that fits the existing pad and rail. You’ll get both prices in writing before any work starts. Call (877) 610-2993 for a site visit.
Not always, but it’s common in Powder Springs neighborhoods built from about 1993 to 2010. Builders often pulled 14-gauge wire with no conduit from the house panel to the gate. A new LiftMaster or FAAC operator can draw more current than that wire safely carries. If the wire is undersized, yes, you need a new conduit run. We’ll test the line and show you the numbers before you spend a cent. Call (877) 610-2993.
It’s almost always both. The crack starts because the clay under the footing moved, which tilted the column, which put bending stress on the gate hinges and post. The gate drags because the column moved, not because the hinges wore out first. We repair the column base, then re-hang and re-weld the gate to the corrected alignment. Fixing only the gate or only the masonry means you’ll be back here next year. Call (877) 610-2993 for an honest assessment.
On a 2004-built home off Dallas Highway in the Brownsville Station subdivision, our crew found a double swing gate sagging hard at the hinge post. The lower hinge had torn its lag bolts loose from the brick column after years of clay-driven heave. We cut out the failed hinge plate, welded a thicker-gauge plate to the existing post after drilling and epoxying new anchors into the column, re-hung the gate with a sag-correction bracket, and re-set the safety photocells. The gate swings clean again, and the post is no longer the weak point. That’s the standard we hold for every Powder Springs job.
If your gate is sagging, binding, or just won’t cycle, call (877) 610-2993 and talk to a person who answers the phone. We’ll give you a straight price and a straight timeline. Hal has been fixing gates in this country for over two decades, and his name is still on the shop. That is the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Powder Springs and surrounding communities since 2001.