Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Poolesville
If a farm gate won’t swing or a weld point has snapped on a driveway gate in Poolesville, we can usually have it repaired the same day. Gatewood Fence & Gate has been doing gate parts and welding work across the 20837 ZIP since Hal Gatewood started the company in 2001, and we know what Poolesville’s gates demand that suburban gates just don’t. Heavy tubular steel, agricultural-grade hinges, solar openers on gravel lanes. That’s our everyday work here. Call (877) 610-2993 and a live person answers, any hour.
Why Gatewood Fence & Gate Is Poolesville’s Preferred Gate Parts & Welding Company
We don’t run a call center and we don’t route your job to whoever’s closest. Hal runs the shop, the name is on every invoice, and the address is published. When someone in Poolesville calls about a sagging gate or a seized hinge, the person who shows up knows the difference between a gate that’s failing and one that needs a different approach entirely. Our Gate Parts & Welding team welds on site, in your driveway or farm lane, not back at some shop an hour away.
Poolesville customers keep calling us back because we fix the actual problem. A gate sags in the hinge post, not in the middle, and that’s where we start. If a bottom rail rusted through on a 20-year-old tube gate, we cut out the bad section and weld in new steel rather than selling you a whole gate. That’s not upselling, it’s just how a repair shop should work.
Our Gate Parts & Welding Services in Poolesville
Hinge Replacement
Freeze-thaw cycling here in the Piedmont lowlands works on ground-set posts all winter. The ground swells, the post leans a few degrees, and suddenly the hinge binds. Every spring we’re replacing barrel hinges and weld-on strap hinges on Poolesville farm gates that shifted over the cold months. We square the post, set the new hinge, and the gate swings clean again. A typical hinge replacement in Poolesville runs $180 to $340 per hinge depending on the steel weight and whether we need to cut a frozen pin.
Post Replacement
When a hinge post leans far enough, the fix isn’t another weld. It’s digging out the old footing, setting a new post in concrete, and rehanging the gate. The agricultural reserve properties around West Willard Road and Elgin Road have heavy gates sitting on posts that were sunk 30 years ago with no concrete collar. We pull those rotted or heaved posts, pour a proper footing, and rehang the gate so it stays square through next winter. Post replacement in Poolesville typically runs $400 to $850 depending on post size and how much old concrete we have to break out.
Rail Repair
Bottom rails rust through on uncoated tubular steel, especially where horses and livestock brush against the gate or where gravel dust holds moisture against the metal. We cut out the rotted section and weld in new tubing. The gate stays in your driveway; we don’t haul it off unless it’s genuinely beyond saving. On the high-end ornamental gates near the town core, rail repair is usually where we find previous sloppy welds somebody left behind. We grind those out and do it right.
Custom Welding
Poolesville has more bespoke gatework than almost anywhere else in Montgomery County, because the agricultural reserve zoning means big estate entrances and horse farm gates. We fabricate reinforcing saddles, weld on new hinge plates, build custom latch mounts for livestock-rated hardware, and repair ornamental ironwork on the century-old farmhouse properties. If you need a gate part that doesn’t exist off the shelf, we make it. Custom welding in Poolesville runs $150 to $600 depending on the fabrication, and we quote that price before we strike an arc.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Poolesville
We stock parts for Viking, Linear, and Ghost Controls openers because those show up constantly on Poolesville farm lanes. DoorKing also appears on the larger estate gates. When a solar charge controller fails or a 12V battery bank goes flat on an automatic gate off a gravel lane, we don’t wait on a parts truck. We carry the common boards, batteries, and limit switch kits in the truck so the gate gets running the day we show up. For older openers on remote equestrian lanes, we can often rebuild what another company would replace.
Common Gate Parts & Welding Problems We See in Poolesville Homes
- Post heave from freeze-thaw cycles. The Piedmont lowlands get sharp temperature swings all winter. Ground-set posts expand and contract, the hinge side leans, and the gate starts dragging or binding. Left alone, the weld points eventually snap from the strain.
- Dead solar openers on remote lanes. Running utility power to a back pasture gate costs too much, so Poolesville horse farms run solar. A corroded charge controller or a dead battery bank means the gate stops answering. We diagnose and rebuild those on site.
- Rusted bottom rails and hinge plates. Humidity sits in the Potomac valley all summer. Uncoated tube steel gates rust from the bottom up, especially where gravel dust traps moisture. We cut out the bad metal and weld in new.
- Latch and lock failures on livestock-rated hardware. Heavy gates put stress on latches that no suburban privacy fence ever does. When a slam latch or cane bolt fails on a paddock gate, we replace it with hardware rated for the weight.
Pricing for Gate Parts & Welding in Poolesville, MD
Here’s what we actually charge in Poolesville, not a vague “it depends.” Hinge replacement runs $180 to $340 per hinge. Post replacement runs $400 to $850 including concrete and rehanging the gate. Rail repair runs $150 to $500 depending on how much steel we cut out and weld back. Custom welding starts around $150 for a small fabrication and goes to $600 for a complex repair. A seized opener or battery bank repair on a solar gate typically runs $250 to $500. Every price is quoted and agreed before any work starts. You get a written number before we touch the gate, and that number doesn’t change at the door. We also take $40 off any repair over $200, and seniors and veterans get a permanent 10% discount. Call (877) 610-2993 for an exact quote, free.
We Also Serve Cities Near Poolesville
Our Gate Parts & Welding in Poolesville service area extends through Darnestown, North Potomac, Travilah, and Germantown. Same local crew, same 90-Day Done Right Promise, same live phone answer any hour. If you’re on the edge of the agricultural reserve and not sure which town you count as, call and we’ll tell you straight.
Serving Poolesville, MD - Our Local Coverage Area
We’re based in the Poolesville area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Poolesville
The ground here freezes and thaws repeatedly through winter, which heaves the hinge post a little more each year. Once the post leans a few degrees, the gate’s entire weight hangs off the hinge barrel instead of the post footing, and every spring it’s lower than it was in the fall. We fix it by squaring the post footing, not just tightening the hinge bolts. Fix the panel without the post and you’ll fix it twice. Call (877) 610-2993 and we’ll come look, free estimate.
Yes. We weld on site, in the driveway or the farm lane. We cut out the rotted section, fish in new tube steel sized to match, and weld it in place with the gate still hung. Removing the gate and hauling it to a shop just adds days and risk of racking the frame in transit.
Yes. Poolesville solar gates run on Viking, Ghost Controls, and Linear openers wired to 12V battery banks and charge controllers. The failure points are the charge controller and the batteries, not the opener motor itself. A suburban LiftMaster on utility power doesn’t have that failure mode. We carry the boards and batteries for these systems and we know how to test a solar array output, so the gate doesn’t die again after the next cloudy stretch. If your solar gate is dead this week, call (877) 610-2993.
Any automatic gate operator installed in Montgomery County has to meet entrapment protection standards, which means monitored safety edges, photo eyes, and proper force settings. When we weld a new operator onto an old farm gate, we have to account for the gate’s weight and the way it’s been re-welded over the years. The safety edges have to run the full length of the gate and be wired so the gate reverses on contact. We handle that as part of the installation, not as an afterthought.
Yes, but it takes care. Old iron is often hand-forged and we have to match the heat and filler rod to the existing metal so the repair doesn’t crack the surrounding structure. We grind back to clean metal, preheat where it’s needed, and weld with a rod that matches the composition. The goal is a repair that holds for decades and doesn’t look like a patch job. Call (877) 610-2993 and we’ll give you a straight read on whether the old gate is worth saving.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Poolesville since 2001.