Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Pine Island Ridge
Gate parts and welding in Pine Island Ridge usually means one of two things: a wrought iron gate that has rusted through at the welds after 40 years of Broward County humidity, or a concrete post that has shifted on the old Everglades fill and thrown the whole gate out of plumb. We fix both, on site, without hauling your gate to a shop. Hal Gatewood has been doing this since 2001, and the person who answers the phone at (877) 610-2993 is the same person who will show up at your driveway.
Most of the work we do in Pine Island Ridge is retrofitting, not replacing. The community was built in the 1970s and 1980s, which means the original ornamental iron gates predate modern safety standards and are now showing their age at every hinge point, weld seam, and post base. We know exactly what that looks like because we see it every week. If you need Gate Parts & Welding done right, you want someone who understands older ironwork and the HOA rules that come with it.
Why Gatewood Fence & Gate Is Pine Island Ridge’s Preferred Gate Parts & Welding Company
We are a locally owned, owner-operated shop. Hal Gatewood’s name is on the business, his address is published, and his license number is public. That is not a marketing line; it is the reason people in Pine Island Ridge call us when a gate sags or a weld cracks. You can look us up before you call. You can drive to the shop and look Hal in the eye. That is the oldest accountability there is.
Residents across Pine Island Ridge have been calling us for years to fix gates that national outfits quoted for full replacement. We repair first. If a hinge post is corroded at the base, we do not tell you the gate is shot. We cut out the bad section, weld in new steel, and re-hang the gate so it clears the driveway again. Every job carries our 90-Day Done Right Promise in writing. If it is not done right, one call brings us back. No runaround.
We answer the phone with a live person, 24 hours a day, seven days a week. Not a voicemail, not a call center three states away. When your gate will not close at 10 p.m. and your dog is eyeing the opening, you get a real human on the line. And we get to Pine Island Ridge fast, because we are based in the South Florida metro and our crews work this area constantly.
Our Gate Parts & Welding Services in Pine Island Ridge
Here is what we actually do for gates in Pine Island Ridge, the work most homeowners in this community need when an iron gate hits the 40-year mark.
Hinge Replacement
Hinges fail before anything else on an iron gate, and in Pine Island Ridge they fail faster because sprinkler overspray keeps the bottom hinge damp year-round. We carry heavy-duty barrel hinges, weld-on hinge tabs, and adjustable hinges that let us fix a sag without cutting into the original scrollwork. A hinge replacement in Pine Island Ridge typically runs $150 to $350 per hinge, depending on gate weight and whether we need to reinforce the post behind it.
Post Replacement
Concrete post footings in Pine Island Ridge heave and sink with the wet-dry cycles on the old Everglades fill. When a post moves, the gate binds at the hinge and the welds start cracking. We saw this recently on a 1970s swing gate off SW 92nd Avenue near the ridge’s eastern crest. Summer stormwater had pooled at the post base, the steel corroded through, and the gate dropped two inches. We bored a new concrete footing 30 inches deep, sleeved the old anchor area with new steel, and re-hung the gate with fresh hinges. Post replacement with a new steel post and footing in Pine Island Ridge generally runs $600 to $1,200, which includes concrete work and re-hanging.
Rail Repair
Forty-year-old painted iron gates rust through at the weld seams along the bottom rail first. That is where sprinkler water sits and where the paint was thinnest from decades of sun. We cut out the rotted section and weld in matching steel, then grind and paint to match the original finish. Most rail repairs in Pine Island Ridge run $250 to $600 per section, depending on how much tube we are replacing and whether the ornamental pickets above need re-welding too.
Custom Welding
The original ornamental iron in Pine Island Ridge was built before modern UL 325 entrapment standards. That means most gates lack safety photocells, and many cannot accept modern operators without modification. Our custom welding work here often involves drilling and reinforcing hinge posts so they can accept retrofit hardware without changing the HOA-approved silhouette. Hal welds on site, in your driveway. He fixes the gate where it hangs, not on a bench 20 miles away. Custom welding projects in Pine Island Ridge start around $200 for small repairs and run up from there based on scope.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Pine Island Ridge
We service and retrofit the major gate operator brands you are likely to have in Pine Island Ridge, including FAAC, Linear, BFT, and Viking. We also stock local parts for these systems so we are not waiting on a distributor when your gate is stuck open. If you have a legacy Linear operator from the 1990s that no longer closes all the way, or a FAAC board that got fried in a lightning storm, we can usually retrofit it without ripping out the whole system. Faster turnaround, less cost, same HOA-approved appearance.
Common Gate Parts & Welding Problems We See in Pine Island Ridge Homes
- Bottom rail rot – Original 1970s and 1980s iron gates rust through at the weld seams along the bottom rail because sprinkler overspray keeps that area damp for years at a time. We cut out the bad steel and weld in new material, then paint to match.
- Heaved post footings – The high water table and seasonal wet-dry cycles on former Everglades drainage land cause concrete footings to heave or sink, throwing swing gates out of plumb until the hinge welds crack. We re-set posts with deeper footings and proper drainage.
- Non-compliant legacy operators – Many original community entry gates in Pine Island Ridge run on old Linear or DoorKing operators that lack modern loop detectors and safety photocells. After a lightning strike or brownout, they freeze mid-cycle. We retrofit them to current UL 325 compliance instead of replacing the whole gate.
- Spalling anchor bolts – Pine Island Ridge’s slight natural elevation gives marginally better drainage than the flatlands around it, but water still pools at the base of gate posts after summer storms. That standing water causes concrete spalling around anchor bolts, which loosens the post and stresses every hinge. We see this as a repeat service call every rainy season.
Pricing for Gate Parts & Welding in Pine Island Ridge, FL
Here are the numbers we quote most often in Pine Island Ridge. A hinge replacement runs $150 to $350 per hinge. Post replacement with a new footing runs $600 to $1,200. Rail repair runs $250 to $600 per section. Custom welding starts around $200 for small fixes and goes up based on how much steel we are replacing. Full gate retrofits with a new operator, safety photocells, and reinforced posts typically run $1,800 to $3,500 depending on gate size and operator brand.
Every price is quoted and agreed before any work starts. You will not get a call from Hal at the door saying it went up. The quote is the quote. We also offer $40 off any repair over $200, a free second opinion on any written estimate you have from another company, and a permanent 10% discount for seniors and veterans. Estimates come to you free.
We Also Serve Cities Near Pine Island Ridge
Our crews work throughout the area, so if you have family or property in Cooper City, Davie, Southwest Ranches, or Pembroke Pines, we can help there too. We know these communities well, and the same 90-Day Done Right Promise applies everywhere we go. For gate parts and welding in Pine Island Ridge or any neighboring city, call (877) 610-2993.
Serving Pine Island Ridge, FL - Our Local Coverage Area
We’re based in the Pine Island Ridge area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Pine Island Ridge
Yes, in almost all cases we can weld the crack in place without touching the gate’s overall appearance. The welding is done on site, the repair area is ground smooth, and we paint to match the existing finish. HOA review is triggered by visible changes to the gate’s appearance, not by structural repairs hidden inside the original silhouette. Call (877) 610-2993 and we will tell you honestly whether your crack is a simple weld or something bigger.
That is almost always a post footing problem, not a gate problem. Pine Island Ridge sits on old Everglades fill, and the soil swells when saturated. Your post heaves up, the gate drops at the latch side, and it drags. We fix it by re-setting the post in a deeper footing with proper drainage stone around it. A gate that drags after rain is a warning sign, not a new normal. Call (877) 610-2993 for a free inspection.
Yes, we can retrofit most legacy Linear operators in Pine Island Ridge with modern control boards, loop detectors, and safety photocells while keeping the original operator housing. This brings the system up to current UL 325 standards without the cost of a full replacement. We stock Linear retrofit parts locally. Most retrofits run $400 to $900 depending on what failed. Call (877) 610-2993 and we will tell you if your operator is worth saving.
We fix the sag at the hinge post, not in the middle of the gate. A gate sags because the hinges wear or the post leans, not because the ironwork itself bends. We either replace the hinges with heavier units, reinforce the post behind them, or both. The scrollwork stays untouched. We have done this dozens of times on original 1970s gates in Pine Island Ridge and the HOA never sees a visible change. Call (877) 610-2993 for a free assessment.
Yes, and that is one of our most common jobs in Pine Island Ridge. We remove the spalled concrete, install a new steel post with a deeper footing, and re-hang your existing gate on it. The gate itself does not need replacing unless its own steel is too far gone, and even then we usually only replace the bottom rail section. Post replacement runs $600 to $1,200. Call (877) 610-2993 and we will look at it before you spend money on a whole new gate.
Call Gatewood Fence & Gate for Gate Parts & Welding in Pine Island Ridge
If your iron gate is sagging, rusting through, or the operator has given up after 40 years, call (877) 610-2993. You will get a live person, an honest answer, and a quoted price before we touch anything. Hal Gatewood owns this shop, he works these jobs, and he stands behind every weld and every hinge with a written 90-Day Done Right Promise. Free estimates. Same crew that shows up at your door is the one you will see at the hardware store. That is how it works here.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Pine Island Ridge and South Florida since 2001.