Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Parker
When a gate stops closing in Parker, the problem is almost never the part you can see. It’s the freeze-thaw cycle working on a weld seam, or Douglas County’s bentonite clay shoving a post out of plumb, or an HOA spec that limits what can actually be repaired. Gatewood Fence & Gate has been fixing those exact failures since 2001, and we’ll give you a straight answer on gate parts and welding before we ever pick up a torch. Call (877) 610-2993 and a live person answers, day or night.
Why Gatewood Fence & Gate Is Parker’s Preferred Gate Parts & Welding Company
Hal Gatewood’s name is on the shop, and that’s not marketing, it’s a warranty. When a Parker homeowner calls about a sagging ornamental gate in a Stonegate HOA or a slide gate seized on its track off Hess Road, the person who shows up is someone who can weld it in the driveway and stand behind the work for 90 days. No subcontracted crew. No “we’ll have someone in your area.” Just Hal and his guys.
Our Gate Parts & Welding team knows the difference between a 80134 planned-community gate with strict material and color specs and a 80138 ranch gate that has to hold up to horses, wind, and clay heave. That local knowledge means we bring the right stock, the right welder, and the right fix the first trip. We answer the phone around the clock, we show up in the window we promised, and every job carries the 90-Day Done Right Promise in writing.
Our Gate Parts & Welding Services in Parker
Post Replacement
In Parker, the post is where most gate failures actually begin. Douglas County’s expansive bentonite clay swells with spring moisture and shrinks through dry winters, and over a few years that cycle walks a gate post out of the ground or leans it enough to bind the hinges. We dig the old footing, re-set the post in concrete with proper depth below the frost line for 5,870 feet of elevation, and rehang the gate so it swings clean. A post replacement in Parker typically runs $475-$950 depending on post size, gate weight, and whether the old footing needs to be jackhammered out.
Custom Welding
Off-the-shelf parts don’t fit every Parker gate, especially in the older HOA communities where ornamental scrollwork was fabricated on site in the late 1990s and early 2000s. We weld on site, in your driveway, so we can match miter joints, picket spacing, and finish exactly. Hairline cracks at scrollwork welds are common after a few freeze-thaw seasons; we grind out the cracked weld, re-tack it, and finish it so an HOA inspector won’t flag it. Custom welding in Parker is billed at $95-$145 per hour plus material, with most repairs done in a single visit.
Rail Repair
Bottom rails on swing gates collect moisture from snow melt and sprinkler overspray, and in Parker’s sharper freeze-thaw cycling, that moisture gets into the steel and rusts from the inside out. We cut out the rotted section, sleeve or weld in a new rail of the same gauge, and redrill the picket points so the repair carries the gate’s full weight without flexing. Expect $280-$520 for a typical rail replacement, depending on gate span and if the gate has to be pulled and blocked to work safely.
Gate Rollers
On rural 80138 parcels, the slide gate is the standard. It’s a 16- to 24-foot tube-steel gate rolling on a V-track, and when clay heave pushes the track out of level by even an inch, the gate binds mid-travel and chews up rollers and the rack. We stock a range of replacement rollers for FAAC, BFT, and Viking slide operators, and we replace the roller and the mounting plate as a pair so you’re not back in six months. Gate roller replacement in Parker generally runs $150-$400 per assembly, and we’ll check the track level as part of the job.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Parker
We’re certified on the major gate operator brands Parker homeowners actually have, including LiftMaster, FAAC, BFT, Linear, Viking, and Ghost Controls. That matters when a solar opener on an equestrian drive off Hess Road needs a replacement arm, or a Linear control board in a 80134 courtyard gate is throwing a fault. We keep common parts in the truck and our shop sees most specialty orders in a couple of days. If you’ve got a gate motor that hums and doesn’t move, call us before you buy a whole new opener. Most of the time it’s a $60 capacitor, not a $900 motor.
Common Gate Parts & Welding Problems We See in Parker Homes
- Post lean from bentonite soil. The weld at the post base is fine; the post itself is moving. Calling it a hinge problem and swapping hinges means you’ll be back out here in 18 months doing it again. We re-set the post and then address any hinge wear.
- Slide track heave on rural parcels. In 80138, a wet spring pushes the track out of level and the gate binds mid-travel, stripping rack teeth. We re-level the track, re-set the post footing, and weld a new rack section rather than replacing the whole run.
- Freeze-thaw cracking at ornamental welds. 80134 gates with scrollwork and mitered corners develop hairline cracks after five to ten years at this elevation. We match the material and finish so the repair passes HOA review.
- Underground operator misalignment. Hydraulic swing operators set in the ground shift as the clay moves, pulling the arm out of line with the gate. We re-bed the operator housing and re-align the arm so the gate stops fighting itself.
Pricing for Gate Parts & Welding in Parker, CO
Here are the numbers we actually quote in Parker. A hinge replacement on a standard ornamental swing gate runs $60-$145 per hinge, depending on gate weight and whether we’re working at the post or the panel. Post replacement, as noted above, runs $475-$950. Rail repair lands between $280 and $520. Custom welding bills at $95-$145 per hour plus material, and a typical scrollwork crack repair runs $180-$325 all in. Gate roller replacement runs $150-$400 per assembly, and we quote the price and get your approval before any work starts. No trip charge inside the county, and $40 off any repair over $200.
We Also Serve Cities Near Parker
If you’re in The Pinery, Stonegate, Castle Pines North, or Dove Valley, you’re still in our service area and we’ll be out the same day for a repair. The soil and HOA issues in those communities are nearly identical to what we see in Parker proper, so the diagnosis comes faster and the fix lasts longer.
Serving Parker, CO - Our Local Coverage Area
We’re based in the Parker area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Parker
The weld isn’t the problem; the soil is. Douglas County bentonite clay expands and contracts with moisture, and that pressure is stronger than any weld bead. We re-set the post on a deeper footing below the frost line and often add a concrete collar wider than the original hole to give the clay less to move. If all we do is weld the post to a bracket, we haven’t fixed anything. Call (877) 610-2993 for an exact quote on a post re-set.
Yes. We weld on site, so we’re matching your actual gate, not a catalog photo. We work in 1/2-inch and 5/8-inch square stock and flat bar, match the scroll radius and the picket spacing, and finish the weld so it reads as original. Before you file the HOA form, call us and we’ll tell you whether the repair is material-matching or should be flagged as like-kind.
A rack is the toothed bar welded or bolted to the gate, and the pinion is the gear on the operator that drives it. When clay heave pushes the track out of level, the gate binds and the pinion strips teeth off the rack. We re-level the track, re-set the post footing, and weld a new rack section rather than replacing the entire run. Typical rack and pinion repair in Parker runs $350-$700, depending on gate length and access.
Yes. UL 325 is the federal safety standard for automatic gate operators, and it applies whether the opener is solar, AC-powered, or hydraulic. On a rural 80138 parcel with a solar opener and livestock, a photo eye or a loop detector is mandatory, not optional. We install entrapment protection on every operator we service, and we won’t hand you a gate that can’t pass inspection. Call (877) 610-2993 to talk through what your gate needs.
Yes, we do this frequently on 80138 equestrian parcels where a swing gate has been binding on a heaved post for years. A slide gate runs on a track with the weight on the track and the rollers, so post heave is much less destructive. We’ll set new posts, lay a level track with a concrete base, weld or bolt a rack to the gate, and install the opener. Call (877) 610-2993 for a free measure and a written price.
Contact Gatewood Fence & Gate for Gate Parts & Welding in Parker
If your gate is sagging, binding, or failing at a weld, call (877) 610-2993. You’ll talk to a real person, we’ll schedule a window we actually keep, and the price is quoted and agreed before any work starts. Gate Parts & Welding is what we do, and Parker is where we do it. The name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Parker since 2001.