Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Norwell
Gate parts and welding in Norwell usually means one of three things: a hinge post that’s heaved out of plumb, a rusted-through latch on an estate gate, or a cracked weld where the frame meets the post. A typical hinge replacement runs $180-$320, a post reset with a new steel sleeve runs $340-$680, and custom on-site welding starts around $190. We get to Norwell fast because we’re based nearby and carry the heavy stuff on the truck. Call (877) 610-2993 and Hal will tell you straight what’s worth fixing and what isn’t.
Why Gatewood Fence & Gate Is Norwell’s Preferred Gate Parts & Welding Company
Hal Gatewood has been under a gate with a welder in his hand since 2001. That matters on Norwell’s wooded drives, where every call has its own peculiar failure. On a job off Mount Blue Street, our crew reset a frost-heaved hinge post for an estate swing gate. The original 4×4 pressure-treated post had rotted at ground level, pulling the LiftMaster operator out of calibration every spring. We sleeved a new steel pipe in a concrete footing, welded new hinge brackets, and re-hung the gate so the Gate Access Control in Norwell-safety photocells and keypad entry-aligned perfectly. The post hasn’t moved through two freeze-thaw cycles since.
What that means for you: we’ve seen Norwell’s specific failures enough times to know where to look first. We don’t run a call center and we don’t have a rotating cast of strangers. The person who answers at midnight is the same person who shows up at your driveway. Hal’s name is on the shop and on every invoice, and the 90-Day Done Right Promise is in writing. If a weld cracks or a post shifts within 90 days, one call brings him back. No runaround.
Being local means we read the lot before we turn a wrench. A gate on a wooded acre off Grove Street fails differently than one a quarter mile from the North River. We know Norwell’s microclimates, and we drive through town every week. When you call for Gate Parts & Welding, you get someone who knows the difference between a gate that needs a hinge and one that needs a whole new footing. That’s the whole point of hiring local.
Our Gate Parts & Welding Services in Norwell
Hinge Replacement
Norwell’s air eats hinges. The North River corridor pushes moisture through the center of town, and a plain steel hinge on a swing gate near conservation land will rust through in as little as six or seven years. We replace them with heavy galvanized or stainless hardware, welded on site so the gate doesn’t leave your driveway. A typical hinge replacement in Norwell runs $180-$320, and we quote the full price before we start. No surprise add-ons at the door.
Post Replacement
This is the big one in Norwell. Plymouth County gets 30 to 40 freeze-thaw cycles every winter, and that heaves posts in ways a Boston condo never sees. We pull the old wood post, sleeve a new steel pipe in a concrete footing that goes below the frost line, and weld the hinge brackets fresh. On Norwell lots, a proper post replacement runs $340-$680 depending on gate width and soil. If the post isn’t the problem but the operator’s out of whack, we’ll tell you that too. Fix the panel without the post and you’ll fix it twice.
Rail Repair
Long wooden drive gates, the kind you see on Norwell’s equestrian properties, take their abuse at the rails. A sagging gate shows it in the middle, but it starts at the hinge post. We straighten rails, reinforce corners with welded steel, and resecure pickets. Norwell’s moist, shaded lots rot wood faster than inland towns, so we often add a steel brace rather than swap the whole panel. Rail repair runs $150-$300 on most residential gates. Forty bucks off any repair over $200 brings that down further.
Custom Welding
This is where we earn our name. Aluminum gate frames crack at the hinge post after years of frost heave; ornamental steel gates rust at the bottom rail; wide farm gates torque under their own weight. Our Gate Parts & Welding crew welds on site, in the driveway, so the gate stays hung and the job gets done in an afternoon. Custom welding starts around $190 and goes up with steel type and complexity. We weld steel, aluminum, and galvanized frames, and we stand behind the work with the same 90-Day Done Right Promise as everything else. Show me the gate closing on its own and I’ll show you where it’s failing.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Norwell
We’re certified on nine major gate brands, and in Norwell we work most often on FAAC, BFT, and Norwell Gate Motor & Opener systems like Linear, along with LiftMaster on the wider estate drives. If your opener is throwing error codes every spring, it’s usually not the board. It’s the post moving under the freeze-thaw cycle and dragging the operator off its mount. We stock common parts locally for Norwell customers, which means less waiting on a shipped bracket. If we can weld the part on site, we do.
Common Gate Parts & Welding Problems We See in Norwell Homes
- Frost heaved hinge posts. The post shifts a quarter inch out of plumb every winter, and by April the gate binds and trips the entrapment protection. The fix is a steel pipe sleeve in a frost-depth concrete footing, not another wood post in the same hole.
- Rust-bloomed hinges and latches. North River humidity accelerates corrosion on spring hinges, barrel hinges, and lock boxes. We see ornamental gates less than ten years old with rust that looks twenty. A weld repair is usually cheaper than replacing the gate.
- Rotted post bases on 1970s-1990s installs. Norwell’s ranch and colonial boom used 4×4 pressure-treated posts directly in shaded, moist soil. That wood rots at ground level within 8 to 12 years here. We replace with steel. It’s the only durable answer for this town’s soil.
- Cracked concrete footings on slide gates. Norwell’s freeze-thaw cycle cracks shallow footings, which lets the gate rack slip and the pinion drive chew itself up. We set deeper footings and re-level the track so the gate rolls clean.
Pricing for Gate Parts & Welding in Norwell, MA
Here’s what Norwell homeowners can expect. Hinge replacement: $180-$320. Post replacement: $340-$680 with concrete and steel sleeve. Rail repair: $150-$300. Custom on-site welding: $190-$700 depending on the frame, the material, and the access. A full re-hang with leveling and operator recalibration: $240-$460. You get $40 off any repair over $200, and there’s no trip charge inside the county. Seniors and veterans get a permanent 10% discount. We quote the full price before any work starts, and that number doesn’t change at the door. Call (877) 610-2993 for a free estimate.
We Also Serve Cities Near Norwell
Gatewood Fence & Gate covers all of Norwell and the surrounding South Shore. We run calls to Hanover, North Scituate, Scituate, and Rockland the same week. If your gate’s failing on a back road in one of those towns, call (877) 610-2993 and we’ll come look.
Serving Norwell, MA - Our Local Coverage Area
We’re based in the Norwell area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Norwell
Because the concrete isn’t below the frost line, and Norwell’s soil is saturated by North River moisture. Water sits around the footing, freezes, expands, and lifts the whole assembly. The fix is a deeper footing with a steel pipe sleeve, done to Norwell’s soil reality, not a generic depth. Call (877) 610-2993 and we’ll dig it once and be done with it.
If it’s a wooden post, expect 8 to 12 years before rot at ground level on most Norwell lots. A steel post in a proper footing will outlast the gate itself. If your gate’s dragging or the operator’s binding, call us before it fails completely. Estimates are free.
Yes. Aluminum gate frames crack at the hinge post from repeated frost heave and heavy swing loads. We weld the crack on site, add a gusset, and the gate stays hung while we work. A typical aluminum frame repair in Norwell runs $190-$420. Call us for an exact price before you start.
They do. Moisture and road grit work into the roller bearings and the track, and the rollers grind down faster than on inland slide gates. We replace rollers, clean tracks, and re-lube with the right grease for wet conditions. A roller and track service runs $120-$250. Call (877) 610-2993 for a quote.
Almost always, yes. The operator is fighting a post that’s moved. The motor works fine, but the gate’s geometry is off. We reset or replace the post, re-hang the gate, and recalibrate the operator so it stops binding. That’s the post problem, and fixing the hinge without it means you’ll fix it twice. Call for a free evaluation.
Call Gatewood Fence & Gate in Norwell
If your gate’s sagging, scraping, rusting through, or throwing codes, call (877) 610-2993. A live person answers, day or night. Hal will drive out to your place, look at the actual gate, and tell you what it needs and what it costs. The name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Norwell since 2001.