Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across North Auburn
Gate parts and welding in North Auburn come down to one question: will the gate open when you need it to? On the acreage parcels and long driveways that define this part of Placer County, a gate that won’t swing or slide isn’t an annoyance. It’s the difference between getting out during a red-flag warning and sitting trapped behind a dead operator. Hal Gatewood has been fixing gates since 2001, and the person who answers when you call is a live person, not a voicemail. Call (877) 610-2993 and tell us what the gate is doing. We’ll give you a straight answer and a price before any work starts.
Why Gatewood Fence & Gate Is North Auburn’s Preferred Gate Parts & Welding Company
North Auburn isn’t a suburb. It’s rolling foothill terrain, decomposed granite, blue oaks, and a lot of gates that have been out there doing their job since the Reagan administration. We know those gates. We also know the people who own them, because Hal’s name is on the shop and his address is published, and that’s the oldest accountability there is. When a post shifts in wet winter soil or acorns pack a slide track in October, you want someone who has seen it a hundred times, not someone reading a diagnostic flowchart off a tablet.
Every repair we do in North Auburn carries the 90-Day Done Right Promise in writing. That’s not a marketing line. If it’s not done right, one call brings Hal back. We also don’t do the thing where the phone quote says one number and the invoice says another. The price is quoted and agreed before any work starts. For North Auburn customers, there’s no trip charge inside the county, $40 off any repair over $200, and a permanent 10% discount for seniors and veterans. A free second opinion on any written estimate is also on the table. We are Gate Parts & Welding specialists, not a replacement crew looking to sell you a whole new gate when a hinge job would do.
Our Gate Parts & Welding Services in North Auburn
We repair first. That’s the whole philosophy. Fix the panel without the post and you’ll fix it twice, and Hal has no interest in charging you twice for the same gate. Here’s what we’re doing most often on North Auburn properties.
Post Replacement
This is the big one in North Auburn. The decomposed granite and clay-heavy soil here moves. Wet winters soak the ground, it expands, the post shifts. Then the gate binds, the operator strains, and eventually the rack and pinion teeth strip out. We dig the old footing, set a new post in concrete that goes deeper than what’s coming out, and get the gate plumb again. A gate sags in the hinge post, not in the middle. That’s where we start, and that’s why post replacement is usually the fix, not a whole new gate.
Custom Welding
When a steel gate cracks, a cast hinge snaps, or a bracket tears loose, we weld it. On site, in your driveway. The gate doesn’t get hauled off to some shop in another county. Hal or one of his crew shows up with the welder, the gate gets repaired where it hangs, and you’re back to working the same afternoon in most cases. North Auburn’s dry summers and wet winters keep us busy with fatigue cracks on ornamental iron, and a proper weld done with the right rod is the difference between a gate that lasts another ten years and one that snaps again next spring.
Hinge Replacement
Hinges wear out. Pins wallow, bushings go egg-shaped, and then the gate drags or the latch stops lining up. On the big 14- and 16-foot swing gates that protect a lot of North Auburn driveways, a worn hinge puts extra load on the operator motor until it burns out. We replace hinges before they take the operator with them. Heavy-duty barrel hinges, pillow block bearings, weld-on replacements, whatever the gate needs. We stock the common sizes, and what we don’t have on the truck, we get fast.
Rail Repair and Gate Rollers
Slide gates on North Auburn acreage run on V-track rails, and those rails take a beating. Blue oak acorns drop into the track every fall, the gate wheels grind over them, and eventually the rail cracks or the rollers chew themselves up. We’ll repair a broken rail section, replace rollers, and then tell you the truth about keeping that track clear before November. The acorn problem here isn’t a cosmetic thing. A packed V-track overloads the motor and trips thermal protection, which is why so many calls come in when they do.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in North Auburn
We’re certified on nine major gate brands, including FAAC, BFT, and Linear, which covers most of what’s installed on North Auburn acreage gates. We keep a running stock of common parts, hinges, hardware, and opener components on the trucks, so a service call to 95603 doesn’t turn into a two-week wait for a bracket to ship from a warehouse. Same goes for Viking operators on the bigger farm gates. If you’ve got a Mighty Mule, a Ghost Controls, a DoorKing, a LiftMaster, or an Elite, we work on those too. And if we can’t get a part, we tell you that up front instead of ordering something that won’t fit and charging you to find out.
Common Gate Parts & Welding Problems We See in North Auburn Homes
These are the calls we’re getting from North Auburn homeowners, week in and week out. You live on hillsides, on decomposed granite, under oak canopy. The gates fail for predictable reasons, and here they are:
- Post heave from wet winters. North Auburn’s clay-heavy soil swells when it’s saturated, pushing the hinge post up or out of plumb. The gate starts binding, the operator whines, and if you don’t address it, you’ll be replacing rack and pinion teeth that didn’t need to go.
- Acorn-packed V-track on slide gates. The native blue oaks along driveways off Mt. Vernon Road and Bell Road drop a heavy acorn load every fall. Those acorns pack into the rail channel, drive wheels climb over them, and the motor draws too much current trying to move the gate. By November, thermal protection trips and the gate just stops.
- Latch and lock misalignment from summer heat. A hundred-degree days warp wood gate leaves and shift steel frames. The deadbolt quits lining up with the strike plate, so the keypad codes fine but the latch won’t actually release. We see this constantly on the 1970s and 1980s ranch properties around North Auburn.
- Fire-season egress failures. When the power drops during a wind event or a PSPS outage, a gate with a dead battery or no fail-open programming stays shut. On a property in the high fire hazard severity zone, that’s a life-safety problem, not a convenience problem. We test battery backups and fail-open settings on every North Auburn service call, whether you ask or not.
Pricing for Gate Parts & Welding in North Auburn, CA
Upfront pricing matters to us because it’s the first thing other gate companies get wrong. Here are honest ranges for the most common North Auburn work:
- Hinge replacement typically runs $180-$420 per hinge, depending on whether it’s a weld-on barrel hinge or a heavier pillow block bearing for a wide acreage gate.
- Post replacement usually falls between $450 and $900 for a standard swing gate post, including digging the old footing, new concrete, and resetting the gate plumb.
- Rail repair on a slide gate generally runs $250-$600 depending on how much rail section needs cutting out and rewelding.
- Custom welding is billed at $95-$145 per hour plus materials. A typical crack repair on an ornamental-iron gate leaf takes an hour or two.
- Gate roller replacement runs $120-$300 per set for most residential slide gates in the 95603 area.
Every quote is written down and agreed to before we touch the gate. If we find something else while we’re in there, we stop and talk to you first. No surprise line items. Call (877) 610-2993 for a free estimate on any of this, and remember the $40-off-any-repair-over-$200 offer and the senior and veteran discount.
We Also Serve Cities Near North Auburn
We do most of our work right here in North Auburn, and we also serve Auburn, Loomis, Lincoln, and Rocklin. If you’re on the line between two service areas, call and ask. Chances are we’re already working a gate on your road. This page covers Gate Parts & Welding in North Auburn, and if you’re a few miles down 49 or out by the edge of Loomis, the same crew answers the phone.
Serving North Auburn, CA - Our Local Coverage Area
We’re based in the North Auburn area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in North Auburn
Install a battery backup on the operator, confirm the gate is programmed to fail open on power loss, and add a Knox-box if your driveway length puts the gate out of sight of the house. North Auburn sits in Placer County’s high fire hazard severity zone, and during a red-flag evacuation, the power usually goes out before the fire gets to you. A gate that won’t open on battery is a gate that traps you. We’ll test the battery, reprogram the fail-safe, and weld in a Knox padlock hasp where the fire department can reach it. Call (877) 610-2993 and we’ll walk the gate with you.
Acorns. North Auburn’s blue oaks drop thousands of them into the V-track every fall, and they pack down into a gritty paste once the rains start. The drive wheels can’t roll over it, the motor draws higher current, and the thermal protection shuts the gate down. The fix is a track flush and motor-load test before the acorns turn to mush, then maybe a new set of rollers if the old ones have chewed themselves up. We schedule these as a standard autumn service for North Auburn slide gates every year.
You replace the post. In the overwhelming majority of cases we see in North Auburn, the gate leaves themselves are fine; it’s the post that shifted in decomposed-granite or clay-heavy soil. We set a new post deeper than the old one, rehang the gate, and weld on fresh hinges if the old ones are wallowed out. A new gate costs thousands. A post replacement costs hundreds. We’ll tell you which one you actually need, and we won’t sell you a gate you don’t.
Yes, and we see a lot of them in North Auburn where running mains power down a long driveway doesn’t pencil out. Solar operators from FAAC, BFT, Viking, and Linear are all in our service rotation. We check panel output, battery health, charge controller settings, and actuator draw. In the winter months with low sun angles and short days, a dirty panel or a battery that’s lost capacity will leave the gate dead by morning. We’ll test the whole system and tell you what’s wearing out before it strands you at the gate or, worse, keeps the gate closed when you need out.
Automatic gates under Placer County enforcement must have a listed primary and secondary entrapment protection device: a monitored photoelectric beam across the gate opening, an edge sensor or contact strip on the leading edge of the gate, and a pressure-limiting function on the operator itself. For a slide gate, an anti-lift and anti-fall guide system is also required. We install and test all of it on every new operator, and we can inspect an existing setup to make sure it still passes. A gate that moves on its own without working safety eyes is a lawsuit waiting to happen and a hazard to kids and livestock. Call (877) 610-2993 for a safety inspection.
Call Gatewood Fence & Gate for North Auburn Gate Parts & Welding
If your gate is stuck, sagging, grinding, or just won’t stay aligned, call (877) 610-2993. You’ll get Hal or one of his crew on the phone, not a recording. We’ll give you a straight answer, a written price, and a time window we actually keep. North Auburn is our backyard. We know the soil, the oaks, the fire zone requirements, and the gates. The name is on the shop, and the shop is down the road. That’s the accountability that matters.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving North Auburn since 2001.