Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Normandy Park
Gate hardware fails differently in Normandy Park, WA than it does ten minutes inland. Salt-laden air off Puget Sound works into hinge pins, welds, latches, and operator boards at a pace that surprises homeowners who moved here from places with gentler weather. If your swing gate sags, drifts, or squeals on a bluff-side driveway, we repair it in place, usually the same day we visit. Call (877) 610-2993 and a live person answers, not a phone tree. Hal Gatewood has been fixing gates since 2001, and his Gate Parts & Welding work happens on the gate in your driveway, not in a shop across town.
Key Takeaways:
- Salt-air corrosion means hinge pins and welds on Normandy Park gates need stainless or galvanized hardware, not standard steel.
- Sloped, bluff-side driveways cause a gravity-drift failure mode we correct with proper hinge-pin alignment and post footing work.
- We carry galvanized hinge straps, stainless pins, and rust-resistant hardware sized for the older ornamental and cedar gates common here.
- Every job is quoted and agreed before we start. Every job carries the 90-Day Done Right Promise in writing.
Why Gatewood Fence & Gate Is Normandy Park’s Preferred Gate Parts & Welding Company
People in Normandy Park tend to do their homework. They want a name they can verify, an address they can drive past, and a person who will stand behind the work. That’s us. Gatewood Fence & Gate offers Gate Installation - Normandy Park and is locally owned and owner-operated, with a published address and license number anyone can look up. Hal Gatewood’s name is on the shop and on every invoice we write. A live person answers our phone 24 hours a day, 7 days a week. Call late after a windstorm drops a fir branch on your slide track and you’ll talk to someone who can actually help, not a voicemail.
We work across Normandy Park regularly, from the lanes up on the bluff to the driveways that drop toward the Sound. Our crews know which gates in this area were installed in the 1960s and 1970s, which operators are original to the property, and which hardware actually holds up against marine air. The person who shows up is background-checked and in uniform. But more important, the person who shows up is accountable. Hal has been at this since 2001, and a 90-Day Done Right Promise means one call brings him back, no runaround.
We also carry a standing offer that matters to homeowners who have been burned before: $40 off any repair over $200, no trip charge inside the county, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans. None of that requires haggling. It’s just how we work.
Our Gate Parts & Welding Services in Normandy Park
Hinge Replacement
On bluff-side lots around Normandy Park, hinge pins take a beating. The gate’s weight sits on the hinges, and when the driveway slopes toward the Sound, that weight loads unevenly. A gate sagging a half inch at the latch is often a hinge pin that has worn into an oval. We replace hinge pins with stainless steel where the salt air demands it, and we realign the gate so it clears the sensor and closes flush. A gate sags in the hinge post, not in the middle, and that is where we start.
Post Replacement
This is the repair that fixes what other companies want to cover up. When a hinge post rots at the base or a welded post foot has rusted through from standing water and salt exposure, replacing the hinge alone won’t hold. We cut out the corroded post footing, pour a new one with stainless anchor bolts, and rehang the gate to clear the sensor. In Normandy Park, where many posts are original to mid-century homes, post replacement is common between years 40 and 60 of a gate’s life. Most gate post replacements in Normandy Park run $800-$1,800 depending on post material, footing depth, and whether the gate is iron or cedar.
Rail Repair
Ornamental iron gates common on Normandy Park properties rust from the inside of the bottom rail first, where moisture collects. We see pinhole rust and split-weld seams on the bottom rails of gates installed in the 1960s and 1970s. Rather than swapping the gate panel, we cut out the rotted section and weld in new steel, then prime and coat it for marine exposure. Fix the panel without the post and you’ll fix it twice, so we check the post foot and hinge alignment at the same time.
Custom Welding
Not every gate part is available off a shelf. When a custom gate from the 1950s needs a new latch bracket, a rein welded hinge strap, or a gate frame section rebuilt, we weld it on site. Our truck carries a welder, and the work happens in your driveway. That matters in Normandy Park because custom iron gates built for these wooded, bluff-side lots rarely match today’s catalog hardware. Custom welding in Normandy Park typically runs $250-$700 per repair point, and we quote it before any work starts.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Normandy Park
We service Normandy Park Gate Motor & Opener systems from DoorKing, Linear, and Ghost Controls, among others. That covers most of the automatic swing and slide gate openers installed on Normandy Park properties from the 1990s through today. We keep common replacement parts and weld-ready steel on the truck, which means a hinge pin, latch bracket, or short rail repair often gets finished the same visit. When your opener brand is old enough to have a phone support line that no longer answers, we can usually match or upgrade the board and gearing without replacing the whole operator.
Common Gate Parts & Welding Problems We See in Normandy Park Homes
- Salt-seized pintle hinges on bluff-side gates. Marine air doesn’t just coat the surface; it gets into the hinge pin and bearing, rusting them together until the gate binds and squeals. Stainless steel pins and regular seasonal lubrication are the only fix that lasts here.
- Storm debris jamming slide gate tracks. The dense fir and cedar canopy over Normandy Park lots drops needles, cones, and branches onto slide tracks and safety photocells all wet-season long. A track full of wet cedar debris trips the operator into fault mode and burns out the motor over repeated cycles.
- Gravity-drift on sloped driveways. When a swing gate sits on a drive that tips toward the Sound, worn hinge pins let the gate drift open or closed on its own. We see this constantly on Normandy Park bluff lots and almost never on the flat streets of neighboring Burien.
- Wood gate members swelling and racking. Cedar gates absorb the constant moisture and expand, pulling lag screws out of posts and twisting the frame. Sag correction and post replacement are the norm, not the exception, on gates original to 1950s-1970s Normandy Park homes.
Pricing for Gate Parts & Welding in Normandy Park, WA
Hinge replacement runs $180-$420 per hinge, depending on whether we weld in a new galvanized hinge strap or repair the existing one. Post replacement typically lands between $800-$1,800 in Normandy Park, with the range driven by post material, footing depth, and whether the gate is iron or wood. Custom welding of a gate frame, latch bracket, or rail section typically comes in at $250-$700 per repair point. Latch and lock work usually runs $95-$250. These are the numbers Normandy Park homeowners see most often, quoted before any work starts.
| Normandy Park Gate Parts & Welding | Typical Range |
|---|---|
| Hinge replacement (per hinge) | $180-$420 |
| Post replacement | $800-$1,800 |
| Custom welding (per repair point) | $250-$700 |
| Latch & lock replacement or repair | $95-$250 |
These ranges include labor and materials. We price the job before we touch the gate, and the number we agree on is the number on the invoice. No trip charge inside King County. Seniors and veterans get 10% off permanently, and any repair over $200 takes $40 off. Call (877) 610-2993 for a written quote without the runaround.
We Also Serve Cities Near Normandy Park
Our service area covers Gate Parts & Welding in Normandy Park and the communities around it. Need gate work in SeaTac, Tukwila, Burien, or Boulevard Park? We work those neighborhoods too, and the same crew, pricing promises, and 90-Day Done Right Promise apply. A live person answers 24/7, and we schedule around your day, not our convenience.
Serving Normandy Park, WA - Our Local Coverage Area
We’re based in the Normandy Park area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Normandy Park
Salt-laden marine air off Puget Sound settles into hinge pins and bearing surfaces, rusting them together months or years before you’d see the same failure in Burien or SeaTac. Stainless steel pins and marine-grade grease are the standard fix on bluff-side lots. If your gate is already squealing or binding, the hinge may be beyond lubricating and due for removal and rebuild. Call (877) 610-2993 and we’ll tell you straight which it is.
It’s common on these sloped lots, but it isn’t normal gate behavior. The gate’s weight slides down the driveway grade and wears hinge pins unevenly until the gate drifts under its own weight. We correct it by replacing the hinge pins, sometimes the hinge post itself, and realigning the gate so it stays put and clears the Gate Access Control in Normandy Park safety sensors. This is a failure we see all over Normandy Park and almost never on flat streets in Burien. A quote is free, and we do the work in your driveway.
If the post moves when you push the gate, if the base shows rust-through or rot, or if the gate sags even with new hinges, the post is the problem. Welding the hinge back onto a failing post buys months, not years. On a Normandy Park property with salt air, a post that has corroded through at the base usually gets cut out and replaced with a new footing and stainless anchor bolts. We’ll show you the post before we cut anything, and the price is agreed up front.
Hot-dipped galvanized steel or stainless steel is the right call for hinge pins, hinge straps, and welded components within a mile of the Sound. Standard painted steel corrodes under the paint where you can’t see it until a weld fails. On Normandy Park properties, we specify galvanized hinge straps with stainless steel pins for anything that carries gate weight. That combination costs more up front and lasts decades longer than bare steel, which rusts out in this marine air within a few years.
In most Normandy Park cases, yes, replacing the hinge post restores the gate. The gate metal itself is often sound, and the problem is a soft footing, a rusted post base, or worn hinge pins. We repair what’s failing and leave what’s good. You only need a new gate panel if the gate’s own frame is rotted through or the bottom rail is collapsing. Call (877) 610-2993 and ask Hal to look at it. You’ll get a straight answer, and the estimate is free.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Normandy Park and South King County.