Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Mukilteo
If your gate is sagging, binding, or rusting through near the hinges, the fix usually comes down to two things: the right parts and a weld that holds. In Mukilteo, WA, the salt air off Puget Sound means standard galvanized hardware fails years faster than it should. That’s why our Gate Parts & Welding work here leans hard on 316 stainless and powder-coated aluminum, spec’d for marine conditions rather than inland assumptions. We service the 98275 zip code and every bluff street, subdivision, and waterfront lane in between. Call (877) 610-2993 and you’ll get Hal or one of his crew, not a voicemail tree.
Why Gatewood Fence & Gate Is Mukilteo’s Preferred Gate Parts & Welding Company
Hal Gatewood has been fixing gates since 2001, and his name is on the shop. That’s the short version. The longer version is that when a hinge post tears loose on a bluff property above the ferry terminal, we show up with a welder in the truck and fix it in the driveway. We don’t haul gates off to some shop and leave you waiting. Gate Parts & Welding in Mukilteo is what we do full time, and after 29 years of serving this area, we know which streets eat hardware fastest. The person who answers the phone at (877) 610-2993 is the same person who’ll stand behind the work. Every job carries the 90-Day Done Right Promise in writing. If it’s not right, one call brings us back. No runaround.
Our Gate Parts & Welding Services in Mukilteo
Hinge Replacement
Hinges are usually the first thing to go on a Mukilteo gate. Salt-laden air works its way into the pin and barrel, and within a few years a galvanized hinge has rusted through, letting the gate sag and scrape. We replace them with 316 stainless hinges on bluff properties and powder-coated aluminum on standard subdivision lots near Harbour Pointe and Mukilteo Boulevard. The gate gets lifted, the old hardware cut off, and the new hinges welded or bolted in so it swings clean. A hinge replacement in Mukilteo typically runs $180 to $340 per leaf, depending on gate weight and how far gone the existing mounts are.
Post Replacement
On the steep, terraced lots that dominate Mukilteo’s 1980s and 1990s subdivisions, hinge posts take a beating from soil movement and moisture. Post footings shift, the post leans, and welds crack at the base. We cut out the old post, sink a new one deeper than the original, and weld it true. On a bluff street above the ferry terminal, we replaced the hinge post on a 1990s swing gate after the lower hinge tore clean out of a corroded footing. The original galvanized hinges had rusted through, so we welded in a new powder-coated aluminum post and swapped to 316 stainless hinges and latch hardware. Post replacement in Mukilteo generally runs $450 to $900, including removal, new post, concrete, and re-welding the gate leaf back into place.
Rail Repair
Rails on ornamental steel gates rust from the inside out. By the time pitting shows on the surface, the rail’s already lost a chunk of its strength. We cut out the bad section, weld in matching steel, grind it smooth, and coat it. On west-facing gates near the Sound, we’ll often upgrade the replacement rail to aluminum to cut the rust cycle short. Most rail repairs in Mukilteo land between $140 and $320 per rail, depending on how much of the original needs to come out.
Custom Welding
Off-the-shelf parts don’t always fit a 25-year-old gate on a sloped lot. When a hinge mount is in a weird spot or the gate was welded by someone’s neighbor back in 1997, custom welding is the answer. We weld on site, in your driveway, with the gate still hanging if that’s the cleanest approach. From reinforcing cracked welds to building a new steel frame that matches the existing rails, this is where Hal’s shop experience shows. Custom welding jobs in Mukilteo typically run $120 to $400, priced upfront and agreed before the torch lights.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Mukilteo
Most of the automatic gate operators we open up in Mukilteo are Viking, Ghost Controls, or DoorKing units, and we’ve been inside every one of them. We’re certified to service nine major brands, and we keep common boards, receivers, and safety edges on the truck so a repair doesn’t turn into a two-week wait for a shipped part. If your operator board is corroded from marine fog, we may have the replacement in the truck when we pull up. Salt air does a number on control boards, especially in west-facing enclosures on bluff lots, so we seal enclosures and relocate boards away from direct salt spray when we install or repair them.
Common Gate Parts & Welding Problems We See in Mukilteo Homes
- Galvanized hinges and latches rust through fast. Within a half-mile of the Mukilteo Ferry Terminal, we see exposed steel gate hardware fail in under five years. The fix is upgrading to 316 stainless or powder-coated aluminum, which would be overkill inland but is standard practice here.
- Post footings shift on sloped bluff lots. The steep grades that give Mukilteo its Sound views also mean soil moves with every wet season. A leaning hinge post cracks welds at the base, and the gate starts dragging on the latch side.
- Operator boards corrode from marine fog. West-facing enclosures take the worst of the salt air. Boards develop corrosion across the terminals, and you get intermittent failures, especially on damp mornings. The board may test fine one day and fail the next.
- Steel frames rust from the inside out. A gate can look fine on the outside while the inside of the bottom rail is rusting away. By the time the rail bows or a weld pops, the original tube is usually too thin to weld without replacing the section.
Pricing for Gate Parts & Welding in Mukilteo, WA
Here’s what our Mukilteo customers actually pay. Hinge replacement: $180 to $340 per leaf. Post replacement with new concrete and re-weld: $450 to $900. Rail section repair with welded patch: $140 to $320 per rail. Custom welding: $120 to $400, quoted by the job. What moves the number is gate weight, how much original steel is left to weld to, and whether you’re on a bluff property where we’re spec’ing stainless instead of galvanized. Every job gets a written price before the first cut or weld. No trip charge inside the county, $40 off any repair over $200, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 and we’ll give you a number you can hold us to.
We Also Serve Cities Near Mukilteo
We cover Mukilteo and the surrounding area, including Picnic Point, Picnic Point-North Lynnwood, Everett, and Lake Stickney. Crews run from our Seattle scheduling office, but the gate work happens in your driveway. If you’re on the fence about which side of the county line you’re on, call anyway. Chances are we’re already working a street near you.
Serving Mukilteo, WA - Our Local Coverage Area
We’re based in the Mukilteo area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Mukilteo
Because the salt-laden marine air off Puget Sound is a corrosion machine. Within a half-mile of the ferry terminal, prevailing southwest winds push salt spray up the bluff continually, and standard galvanized hinges can rust through in under five years. The fix is upgrading to 316 stainless or powder-coated aluminum hardware. Call (877) 610-2993 and we’ll spec the marine-grade option so you’re not doing this again in four years.
If the post itself is still sound and the weld is the only failure, we can often grind it clean and re-weld in place. On Mukilteo bluff lots, we see a lot of posts where the steel at the base has corroded right along with the failed weld, and in those cases a patch weld will only buy you a season or two. We’ll tell you straight which one you’re looking at before any work starts. Estimates are free at (877) 610-2993.
316 stainless hinges, latches, and fasteners are the baseline on bluff properties above the Sound. Powder-coated aluminum posts and rails are the second half of the equation, because they don’t rust at all. Galvanized steel, which works fine a few miles east in Lynnwood, is a false economy within a half-mile of the ferry terminal. We stock this spec so the fix happens same trip, not next Tuesday.
Almost certainly, if the operator is in a west-facing enclosure. Mukilteo’s marine fog deposits a fine salt film inside control boards, and that film conducts enough current to throw off the board’s signals on damp mornings. The fix is cleaning and sealing the enclosure, replacing the board if the corrosion is advanced, and relocating the enclosure away from direct salt spray where possible. Call (877) 610-2993 and we’ll open it up and show you exactly what’s happening.
Yes. Most Mukilteo subdivisions from the 1980s and 1990s used similar ornamental steel rail profiles, and we keep matching tube stock on the truck. We cut out the rusted or damaged section, weld in new steel that matches the existing rails, grind it smooth, and coat it so the repair disappears. This is routine work for us, and it’s priced before we light the torch.
Call Gatewood Fence & Gate for Gate Parts & Welding in Mukilteo
When a hinge tears loose or a post footing shifts, the gate’s not going to fix itself, and the salt air won’t either. Call (877) 610-2993 for a free estimate on gate parts, welding, or a full hardware upgrade to marine-grade spec. Hal Gatewood’s name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Mukilteo since 2001.