Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Morristown
Gate parts and welding in Morristown usually means one of two things: a farm gate on acreage that has sagged out of plumb, or a tubular steel frame that’s cracked or rusted through at the rail. We handle both, and we do the welding on site in your driveway so the gate never leaves your property. Most repairs in the 37813, 37814, 37815, and 37816 ZIP codes run $140 to $420 depending on the size of the gate and how much welding or post work it needs. If your gate is binding, dragging, or won’t latch, call (877) 610-2993 and a live person answers, day or night.
Why Gatewood Fence & Gate Is Morristown’s Preferred Gate Parts & Welding Company
We’ve been fixing gates since 2001, and the way we do it hasn’t changed: Hal Gatewood’s name is on the shop, the shop is local, and the person who shows up to weld your gate is the same crew that will stand behind it a month later. That matters in a town like Morristown, where word travels fast and a bad job on Panther Creek Road gets talked about at the diner. Every job we do carries the 90-Day Done Right Promise in writing. If the gate sags again or the weld doesn’t hold, one call brings us back. No runaround, no arguing about who’s at fault.
We answer every call with a live person 24 hours a day. You will not get a voicemail tree or a call center in another state. You get a person who knows gate hardware. And because we’re Gate Parts & Welding specialists rather than a general fence company that does gates on the side, we stock the hinges, posts, rollers, and latch hardware that Morristown’s particular mix of farm gates and residential swings actually require.
Our Gate Parts & Welding Services in Morristown
Hinge Replacement
A gate sags in the hinge post, not in the middle, and that’s where we start. On older Morristown farm gates, the hinge itself is often fine but the post has heaved forward in Hamblen County’s red clay, which throws the whole frame out of square. We replace the hinge, re-plumb the post, or both, depending on what the gate actually needs. In neighborhoods off Buffalo Trail and around Cherokee Park, worn barrel hinges on chain-link drive gates are common, and we replace those with greaseable heavy-duty versions that hold up to freeze-thaw cycles.
Post Replacement
This is the most frequent real fix for a sagging gate, especially on the acreage properties south of town toward Cherokee Lake. A post set in red clay that freezes and thaws every winter will eventually lean, no matter how good the original install was. We dig out the old post, set a new one in a deeper concrete footing, and weld any reinforcement the gate frame needs at the hinge post. On a gravel drive off Cherokee Lake Road, we re-set a 6×6 post that had heaved out of plumb, welded a reinforcement plate at the hinge post, and got the gate swinging level again the same day.
Rail Repair
Ice load is the quiet killer of tubular steel gates in the Holston River valley. When freezing rain coats the top rail and the frame can’t take the weight, you get a bent rail or a cracked weld at the corner. We straighten what’s straightenable and weld what’s cracked. If the bottom rail is rusted through from 47 inches of annual rainfall and the red clay splashing up against it, we cut out the bad section and weld in new tube steel, then repaint or recoat the repair so it doesn’t just rust again next year.
Custom Welding
Not every gate part is available from a catalog, and on older farm gates around Morristown, the original builder is long gone. We do custom welding on site: reinforcement plates at hinge posts, fabricated latch catches, bracket mounts for solar operators, and frame repairs on odd-size gates that were never a standard dimension to begin with. Hal has been welding since 2001, and the philosophy is repair-first. If a gate can be fixed properly with welding, we’d rather do that than sell you a new one you didn’t need.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Morristown
Our crew is certified to service nine major gate brands, including Viking, Ghost Controls, and DoorKing, and we carry parts for all of them so a Morristown repair doesn’t wait a week on a freight shipment. That’s especially important for acreage gates on solar power, where Ghost Controls kits dominate because trenching power down a 300-foot gravel drive costs more than the opener. We also service Elite openers on the residential side. If you have a Gatewood-installed or Gatewood-serviced gate, we know exactly what’s on it because we put most of it there ourselves.
Common Gate Parts & Welding Problems We See in Morristown Homes
- Post heave from freeze-thaw cycles: Hamblen County’s red clay expands when it freezes and contracts when it thaws, and over two or three winters that’s enough to push a gate post out of plumb. The gate starts dragging, the latch misses the catch, and the hinges bind. The fix is a deeper concrete footing, not just shimming the hinge.
- Ice-bent top rails and cracked welds on older farm gates: Morristown sits in a valley that funnels freezing rain, and ice accumulation on a wide tubular-steel farm gate can add hundreds of pounds to the frame. We see bent top rails and cracked corner welds every spring, and the repair is almost always weldable on site.
- Solar gate openers losing power on long, shaded driveways: Tree-lined drives along Cherokee Lake Road and the county roads feeding toward it get limited winter sun, and solar panels that worked in July fall flat in January. Batteries drain, gates strand half-open, and the fix is usually a larger panel, a repositioned mount, or a hybrid setup. We handle the power side as part of the gate service.
- Slide gate rollers binding on gravel: Gravel driveways throw dust and fines into roller tracks, and on sloped drives the track itself shifts with the clay underneath. Rollers bind, the gate jerks, and the motor works harder than it should. We clean, re-align, and replace rollers, and we’ll tell you honestly if the track needs resetting.
Pricing for Gate Parts & Welding in Morristown, TN
A typical hinge replacement in Morristown runs $140 to $260 for a standard residential gate. Post replacement, including digging out the old post and setting a new one in concrete, runs $300 to $550 depending on the depth and whether fencing sections need to be detached. Custom welding repairs run $95 to $250 per hour, and most farm gate frame repairs fall in the $180 to $420 range once labor and materials are accounted for. The price we quote is the price you pay, agreed before any work starts. There’s no trip charge inside the county, and if you have a written estimate from another company, we’ll give you a free second opinion on it. Call (877) 610-2993 and we’ll walk through your gate over the phone, then give you a firm number.
We Also Serve Cities Near Morristown
Our gate parts and welding crew covers Morristown and the surrounding counties, so if you’re in Jefferson City, Newport, Greeneville, or Sevierville, the same crew and the same 90-Day Done Right Promise apply. For Morristown jobs, dispatch and scheduling are coordinated from our metro office, but the people who show up are local crew who know Hamblen County’s cl
ay and the way gates fail in it.
Serving Morristown, TN - Our Local Coverage Area
We’re based in the Morristown area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Morristown
Your gate is sagging because the hinge post is heaving out of plumb in the red clay. Hamblen County’s soil freezes and thaws each winter, and each cycle nudges the post a little further out of square. The gate frame itself rarely bends; it’s almost always the post. The permanent fix is re-setting the post in a deeper concrete footing and re-hanging the gate, which we do on site. Call (877) 610-2993 and we’ll come look at it for free inside the county.
It can, but only if the solar panel is sized for winter sun, not summer sun. Long, shaded drives off Cherokee Lake Road and similar tree-lined routes often undercharge solar gate openers from November through February, and the gate strands half-open when the battery dies. The fix is usually a larger panel, a better mount angle, or adding a backup battery bank. We install and service Ghost Controls solar kits and will set yours up for Morristown’s actual winter conditions, not the national average.
It can usually be welded. The bottom rail is where tubular steel gates rust first in Morristown because clay splashes up from the gravel and holds moisture against the metal. We cut out the rusted section, weld in new tube steel with the same wall thickness, and recoat the area. If the rust has spread into the hinge post or the frame is too thin to weld safely, we’ll tell you straight and quote the replacement. Most farm gates under 12 feet are repairable. For an exact quote, call (877) 610-2993.
Yes. Any automatic gate, whether it’s on a residential driveway off U.S. 25E or a farm entrance on a county road, is required to have entrapment protection, which typically means photo-eye sensors, a reversing edge, or both, depending on the gate type. This is a safety component, not an upsell, and it’s part of any opener install we do. If you’re not sure what protection your current gate has, we’ll check it during the service call.
The main things are keeping the track clear of gravel fines and checking that the track itself hasn’t shifted out of level. On sloped gravel drives in southern Hamblen County, the clay under the track moves with the seasons, and even a quarter-inch of sag makes the gate fight the motor. We replace worn rollers, re-level the track, and set the guides so the gate rolls smoothly. A maintenance call every other year catches most problems before they bend a wheel or burn out a motor.
If your gate is sagging, cracking, binding, or won’t latch, call (877) 610-2993. We’ll quote a firm price before any work starts, and the 90-Day Done Right Promise means we stay on the hook for it. That’s the way we’ve done it since 2001.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, providing Gate Parts & Welding in Morristown, TN.