Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Matthews
Gate parts and welding in Matthews, NC typically runs $180-$650 depending on whether we’re replacing a hinge, resetting a post, or welding a cracked ornamental iron rail. Most repairs are done the same day we arrive, in your driveway, without hauling your gate back to a shop. If you live in Matthews and your gate sags, drags, or won’t close, call (877) 610-2993 and a live person answers – not a menu, not a recording.
We know Matthews. We know the HOAs along McKee Road and the neighborhoods off Weddington Road near the Union County line. We know that in a planned community here, you can’t just swap a black hinge for a bronze one without the architectural review board noticing. That’s the reality of gate work in this town, and we build it into every estimate so you’re not left standing at the gate with non-compliant parts.
Why Gatewood Fence & Gate Is Matthews’s Preferred Gate Parts & Welding Company
Hal Gatewood has been fixing gates since 2001, and the name is on the shop. That matters in Matthews, where a lot of the automatic driveway gates and community entrance gates installed during the 1990s and 2000s buildout are now 15 to 30 years old and failing in clusters. Residents in the same development often call us about the same aging LiftMaster or Linear operator within weeks of each other. We learn the hardware, the soil, and the HOA rules of a neighborhood and that knowledge carries to the next house down the street.
Our Gate Parts & Welding team works across 28104, 28105, and 28106. When you call, Hal or someone from his crew picks up. You get a real person who knows gates, not a call center three states away. And every job carries the 90-Day Done Right Promise in writing – if it’s not done right, we make it right, one call brings us back.
We publish our license number and our address. Hal will tell you to drive to the shop and look him in the eye. That’s the oldest accountability there is, and it’s why Matthews homeowners who’ve been burned by outfits that quote one price on the phone and charge another at the door end up calling us second.
Our Gate Parts & Welding Services in Matthews
Hinge Replacement
A gate sags in the hinge post, not in the middle – and that is where we start. In Matthews, the hinge is usually the first thing to fail because the red clay under the post shifts, tilting the gate and loading the hinge beyond what it was built for. We replace worn hinge barrels and weld reinforced hinge brackets on site, re-aligning the gate to swing true. Fixed right the first time, not patched.
Post Replacement
Post replacement in Matthews means digging past the red clay and setting the new post in a deeper concrete footing. The expansive clay here swells when wet and shrinks when dry, and over a few years that cycle heaves a shallow footing out of plumb. We’ve reset posts in neighborhoods all over Matthews, including the planned communities near the Union County line, and when we’re done the gate hangs level and closes on its own.
Rail Repair
Ornamental iron and aluminum gate rails take a beating in Matthews’s humid summers. Rust pitting starts small and worsens fast, and a cracked top rail on a swing gate is a stress riser that will eventually snap. We cut out the bad section, weld in new material, and grind it smooth so the repair disappears. If your gate is visible from the street or the HOA is picky, we match the profile and finish so the fix doesn’t stand out.
Custom Welding
Sometimes a hinge pulls out and tears the frame, or a slide gate’s rack gets bent and you need more than a part swap. We weld on site, in your driveway, on ornamental iron, aluminum, and steel. Hal has been welding gates since 2001 and would rather fix the gate you have than sell you a new one. In Matthews, where HOA rules often force you to keep the same material and profile, that repair-first approach saves you time and money.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Matthews
We work on FAAC, BFT, Linear, and Viking operators, among others. A lot of the LiftMaster and Linear operators installed in Matthews’s 1990s and 2000s subdivisions are original to the homes, which means they’re now well past their rated service life. When one fails, we stock the common replacement parts locally so we’re not waiting for a part to ship across the country. That matters in Matthews, where an HOA board might give you 30 days to fix a broken gate, and a three-week wait on a control board isn’t acceptable.
Common Gate Parts & Welding Problems We See in Matthews Homes
- Post footings heaved by red clay. The expansive soil under Matthews swells in wet seasons and shrinks in dry ones, slowly tilting concrete-set posts and throwing swing gates out of alignment. This is one of the most common repeat repair calls we get, especially in subdivisions built in the 1990s and early 2000s.
- Rust pitting on ornamental iron in summer humidity. Matthews’s humid summers age exposed gate panels faster than dry climates do. Pitting at weld points and rail joints weakens the frame, leading to cracks that spread through freeze-thaw cycles.
- Aging automatic operators failing in clusters. In HOA-governed neighborhoods with community entrance gates, entire developments share the same vintage equipment. When one LiftMaster or Linear operator fails, the same failure is coming to a dozen other homes in the same neighborhood.
- HOA architectural delays on non-compliant parts. A homeowner orders a replacement latch or operator in a different finish, and the architectural review board rejects it. Now the parts sit in a box while the gate stays broken. We pull the CC&Rs before ordering so that doesn’t happen in Matthews.
Pricing for Gate Parts & Welding in Matthews, NC
A hinge replacement in Matthews generally runs $180-$320, including the new hinge and labor. Post replacement is the bigger job, typically $450-$800, because we’re digging down past the clay, setting a deeper footing, and re-hanging the gate. Rail repair or custom welding usually falls between $200 and $650 depending on how much material is bad and how much finish work the HOA expects. Here’s the straight numbers for common jobs:
- Hinge replacement: $180-$320
- Gate roller replacement: $120-$250 per roller
- Rack and pinion repair: $200-$400
- Post replacement with deeper footing: $450-$800
- Rail repair or custom welding: $200-$650
Every quote is in writing and agreed before any work starts. We honor the number. We don’t add a trip charge inside the county, we offer $40 off any repair over $200, and there’s a permanent 10% discount for seniors and veterans. If another company gave you a written estimate, we’ll give you a free second opinion on it. Call (877) 610-2993 and we’ll give you a real number, not a range that grows at the door.
We Also Serve Cities Near Matthews
If you’re outside Matthews proper, we work in Gate Parts & Welding in Matthews and the surrounding towns too. That covers Mint Hill, Indian Trail, Stallings, and Wesley Chapel. Same crew, same promise, same live person on the phone. The 90-Day Done Right Promise goes with us wherever the job is.
Serving Matthews, NC - Our Local Coverage Area
We’re based in the Matthews area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Matthews
You don’t have to handle it alone. We pull your community’s CC&Rs before ordering parts, and if the repair alters color, material, or profile – even a hinge or post – we’ll help you prepare the architectural review submittal. Many Matthews HOAs require written approval before work starts, and we factor that wait into the schedule so you’re not surprised. Call (877) 610-2993 and we’ll look at your HOA’s specific rules during the free estimate.
Because the post is moving, not the panel. The red clay under Matthews expands when wet and shrinks when dry, heaving shallow post footings out of plumb over time. You can replace the panel three times and it’ll still sag because the hinge post is what’s carrying the load. We reset the post in a deeper concrete footing and weld a reinforced hinge bracket, then the gate stays level.
Yes, and that’s standard practice for us in Matthews. We match the existing profile and finish so the weld repair doesn’t alter the color or material appearance that your HOA architecturally reviewed. If the CC&Rs require exact material match, we source the right stock before we weld. Many Matthews communities require this, and we’d rather do it right the first time than ask you to re-open an architectural review.
Yes. We service and install LiftMaster operators in Matthews, and when an HOA restricts replacement to the same brand and color, we order exactly that. In some Matthews communities, the architectural board has pre-approved specific LiftMaster or Linear models, and we know those lists from working in the area. We’ll confirm what’s allowed before we order so the operator isn’t sitting in a box waiting on approval.
Every 12 months is the right interval for a slide gate in Matthews. The humid summers accelerate wear on the rack and pinion, and the red clay doesn’t help if dust gets into the track. Photocells should be tested with the obstruction test every year too – it’s a UL 325 safety requirement, not just a suggestion. We’ll check all of it in one visit and tell you what’s wearing before it breaks. Call (877) 610-2993 to schedule a check.
Call Gatewood Fence & Gate for Gate Parts & Welding in Matthews
If your gate sags, drags, or won’t operate, call (877) 610-2993. Hal answers. You’ll get a straight answer about whether it’s a hinge, a post, a rack, or an operator, and a written price before any work starts. We weld on site in Matthews, we respect your HOA’s rules, and we stand behind the job with the 90-Day Done Right Promise. The name is on the shop, and the shop is down the road.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Matthews since 2001.