Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Lynnfield
Gate parts and welding in Lynnfield usually come down to one of three things: a hinge post that heaved out of plumb over the winter, a crack in an ornamental iron leaf, or an opener board that died after an icing event. We handle all three, usually on the first trip. Hal Gatewood has been welding and repairing gates since 2001, and the person who shows up at your driveway is the person whose name is on the invoice. Call (877) 610-2993 and a live person answers, day or night.
Why Gatewood Fence & Gate Is Lynnfield’s Preferred Gate Parts & Welding Company
Lynnfield is not a door-to-door kind of town. It’s a place where people ask their neighbor who fixed their gate, then call that name. We get a lot of calls that start that way. Homeowners here have large wooded lots, long driveways, and gates that were installed during the 1990s and early 2000s building boom. Those gates are now 20 to 30 years old, and they’re reaching the age where hinges, posts, and operator boards fail on a schedule set by the Essex County winter.
Our Gate Parts & Welding team works on those older systems constantly. We know which LiftMaster boards are still available, which Eagle operator parts were discontinued years ago, and when it’s smarter to retrofit rather than chase a replacement part that no longer exists. Hal’s been at this since 2001 and he still answers his own phone. If you want to drive to the shop and look him in the eye before you hire him, that’s the oldest accountability there is.
Our Gate Parts & Welding Services in Lynnfield
Hinge Replacement
A gate sags in the hinge post, not in the middle, and that’s where we start. In Lynnfield, hinges on 1990s ornamental gates take a beating from repeated freeze-thaw cycles and, for properties within a half mile of Route 1, salt spray that rusts iron brackets until they crack. We cut out the old hinge, weld in a new bracket matched to the existing operator geometry, and shim the gate so it closes square with the safety edges. $180-$320 for a standard ornamental hinge replacement, including on-site welding.
Post Replacement
This is the single most common repair we do in Lynnfield, and it’s not close. The clay-heavy glacial soils around town hold water, freeze, and expand. A hinge post set at 36 inches will heave out of plumb after enough winters, and once the post moves, the gate drags, the opener strains, and the photocells throw false obstructions. We dig out the old footing, reset a new post below the frost line with proper concrete, and weld the hinge brackets back on. Post replacement in Lynnfield typically runs $400-$750 depending on post size and whether the opener needs re-aligning afterward.
Rail Repair
Slide gates on Lynnfield’s longer driveways rely on a top rail or bottom track that has to stay true. Frost heave bends rails, and road salt eats the weld joints on steel rails near Route 1. We cut out the damaged section, weld in new stock, and grind the joint smooth so the gate runs quiet. Rail repair typically costs $250-$500, less than a full gate replacement by a wide margin.
Custom Welding
When an ornamental iron gate cracks at a scroll joint or a mounting tab snaps off, the right fix is a clean weld on site, not a new gate. Hal welds in your driveway, so the gate never leaves the property and the repairs are matched to the existing metal. Whether it’s a broken picket, a cracked hinge plate, or a gate post that needs a custom bracket for an older Viking operator, we handle it. Custom welding jobs in Lynnfield start around $150 and run up based on the scope of the repair.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Lynnfield
We’re certified to work on nine major gate brands, and in Lynnfield that matters because this town has a lot of legacy operators. FAAC and BFT units are common on the custom homes off Main Street and Salem Street, and Linear openers show up regularly on 1990s developments near the Lynnfield Marketplace area. When we find a Viking or an older Eagle unit that’s still hanging on, we can often repair it with parts we stock locally rather than ordering blind online. If the board is obsolete, we’ll tell you straight, and we’ll give you a retrofit price versus a replacement price so you can decide with real numbers.
Common Gate Parts & Welding Problems We See in Lynnfield Homes
- Hinge posts heaved out of plumb after winter. Clay soil freezes, expands, and pushes posts up and over. The gate drags on the latch side, the opener fights the load, and by April the gate won’t close without a shove. The fix is resetting the post below the frost line, not re-hanging the gate on a bad post.
- Rusted hinge brackets and weld joints near Route 1. Salt spray from winter road treatment settles on iron hardware for properties along Route 1 and the 128 interchange area. Hinges get brittle, crack, and snap. We see welded repairs that fail within two years because the underlying bracket was already too far gone.
- Dead operator boards after icing events. The 1990s and early 2000s LiftMaster and Eagle units around Lynnfield are notorious for logic board failures after a hard freeze. The gate sits dead until the board is replaced or the opener is retrofitted. We stock replacement boards for the common models and can tell you over the phone whether yours is worth fixing.
- Slide gates jumping the track after snowstorms. Snow and ice pack into the track or the rack, rollers bind, and the gate stalls or jumps. Sometimes it’s a worn roller set; sometimes it’s a bent rack section from a gate that was forced open while frozen shut. We diagnose both and fix what’s actually broken.
Pricing for Gate Parts & Welding in Lynnfield, MA
Here’s what Lynnfield homeowners can expect to pay for common gate work. Hinge replacement runs $180-$320 per hinge, welded on site. Post replacement runs $400-$750 depending on post size, soil conditions, and whether the operator needs re-alignment after the post is set. Rail repair runs $250-$500 for a typical slide gate section. Custom welding starts around $150 and goes up with scope. Board replacement for a legacy LiftMaster or Linear opener typically runs $200-$400, and a full retrofitted operator installed runs $1,200-$2,000 when the old unit is beyond saving. Every price is quoted and agreed before any work starts. There’s no trip charge inside the county, and we’ll give you a free second opinion on any written estimate from another company. Call (877) 610-2993 and we’ll give you the number over the phone.
We Also Serve Cities Near Lynnfield
We work throughout the North Shore and the surrounding towns. If you’re in Wakefield, Reading, Middleton, or North Reading, the same crew that serves Gate Parts & Welding in Lynnfield covers your driveway too. Same pricing, same promise, same person on the phone when you call.
Serving Lynnfield, MA - Our Local Coverage Area
We’re based in the Lynnfield area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Lynnfield
Because the hinge post is moving, not the gate itself. Lynnfield’s clay-heavy glacial soil absorbs water, freezes, and expands, which heaves the post up and out of plumb inch by inch every season. The gate sags in the hinge post, not the middle. Fix the post without addressing the frost line and you’ll fix it twice. Post replacement with the footing set below the frost line is the permanent repair. Call (877) 610-2993 and we’ll dig it out and set it right.
If the board is still available and the rest of the opener is mechanically sound, replacing the board is the cheaper fix, typically $200-$400. If the board is obsolete, the motor is wearing out, and the safety edges are original, retrofitting the whole operator usually makes more sense, at $1,200-$2,000 installed. We’ll check the unit and give you both numbers before you decide. Call (877) 610-2993 for an honest assessment.
Yes. We weld on site in your driveway so the gate never leaves the property. We cut back the cracked metal to clean steel, weld in new fill, and grind it down so the repair matches the existing profile. An average crack repair runs $150-$300. Call (877) 610-2993 and we’ll give you a firm price before we strike an arc.
It’s usually one or both: worn rollers that can’t hold the gate in the track, or a rack section bent when the gate was forced open while frozen shut. In Lynnfield, snowpack and ice cause this every winter, and the fix is replacing the roller set or welding in a new rack section. Roller replacement runs $150-$300; rack repair runs $250-$500. Call (877) 610-2993 and we’ll tell you what you’re looking at.
No, replacing a hinge post on an existing automated gate in Lynnfield does not require a permit or a town inspection, as long as the gate’s footprint and operator configuration don’t change. If you’re replacing the entire gate or moving the operator, that’s different. When in doubt, call (877) 610-2993 and we’ll tell you what applies to your specific situation before any work starts.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Lynnfield since 2001.