Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Lawrence
Gate post leaning after the last freeze? Hinge welds cracked on a farm gate? In Lawrence, we fix those problems on site, same visit, usually the same day you call. A typical hinge replacement on a Lawrence gate runs $140-$320, and post replacement with new steel and concrete runs $400-$900 depending on what we find underground. Call (877) 610-2993 and a live person answers, 24/7. Hal Gatewood’s name is on the shop, his address is published, and he’s been at this since 2001.
What sets Lawrence apart for gate work isn’t the weather alone, though the freeze-thaw cycles here do plenty of damage. It’s the ground itself. In the Harrison community, built on the old Fort Benjamin Harrison grounds, gate posts were sunk in military-spec concrete footings that run deeper and wider than anything residential code requires today. That means a post replacement near Fort Ben Harrison often means breaking up an oversized pad before any new steel goes in. Out-of-town crews don’t know to look for that. We do. We’re Gate Parts & Welding specialists who work Lawrence every week, from 46249 acreages down to Oaklandon’s post-war ranches.
Why Gatewood Fence & Gate Is Lawrence’s Preferred Gate Parts & Welding Company
Lawrence homeowners call us because we show up when we say we will, and because we fix what’s actually broken instead of selling a whole new gate. We’ve been locally owned and owner-operated since 2001, with a published address and license number anyone can look up. Hal Gatewood’s name is on the shop and on every invoice. That’s the oldest accountability there is.
Our crews know Lawrence’s two very different gate generations. The 1950s-to-1980s ranch and split-level subdivisions around Oaklandon have wood privacy gates that are now 30 to 50 years old, fighting post rot and hinge fatigue. Then you have the converted Fort Harrison residential enclaves, where the hardware is often institutional-grade and non-standard. We stock parts for both. A live person answers every call around the clock. Not a voicemail, not a call center three states away, not a chatbot. When a Lawrence gate fails at 9 p.m., you get a human on the line who knows the difference between a 46249 driveway and a Broad Ripple alley.
Every job carries the 90-Day Done Right Promise in writing. If it’s not done right, we make it right. One call brings Hal back, no runaround. We answer with a live person, we quote the price before we start, and that price doesn’t change at the door.
Our Gate Parts & Welding Services in Lawrence
Hinge Replacement
Most Lawrence gate sag starts at the hinge post, not in the middle of the gate panel. Fix the panel without the post and you’ll fix it twice. We replace worn or snapped hinges on wood, tubular steel, and ornamental iron gates across Lawrence, including the heavier institutional hinges common in the Harrison community. A typical hinge replacement runs $140-$320 depending on the gate’s weight and whether the post itself needs steel plate reinforcement.
Post Replacement
This is the job where local knowledge matters most. Frost heave from central Indiana’s winter cycles, Marion County commonly sees 20-plus freeze-thaw events a season, shifts Lawrence gate posts out of plumb. In the Harrison community, we often find military-spec footings that require breaking up a concrete pad 30 inches deep before new steel can be set. We do that work on site, weld the new post into the existing concrete where it makes sense, and rehang the gate so it swings true. Typical post replacement in Lawrence runs $400-$900, and we quote it before we dig.
Rail Repair
Wood privacy gates in Oaklandon and other 50s-through-80s subdivisions split rails and pop screws when summer humidity swells the frame against worn hinges. We sister new rails into the frame, reinforce the corners with steel brackets, and weld steel rail replacement for tubular farm gates where livestock pressure has bent the top rail. Rail repair typically runs $150-$400 per rail depending on material and length.
Custom Welding
We weld on site, so your gate stays in your driveway. No hauling it off, no swapping parts that don’t need swapping. That matters in Lawrence, where farm gates are wide, heavy, and often built to non-standard widths around long 46249 driveways. We weld new hinge plates onto round or square tubing, repair cracked welds from livestock pushing against the gate, and fabricate brackets for opener arms when the original hardware no longer exists. Custom welding jobs in Lawrence typically run $120-$500 depending on the scope.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Lawrence
We’re certified to service nine major gate brands, and for Lawrence homeowners that usually means Viking, Ghost Controls, and DoorKing operators on acreage gates, plus Elite openers on residential driveways. We stock common parts for these systems in our local shop, so a Lawrence repair doesn’t wait on a slow out-of-state parts shipment. When the opener’s the problem, we diagnose it on site, tell you the price, and fix it that visit when the part’s in stock. If we need to order, we tell you the timeline before any work starts.
Common Gate Parts & Welding Problems We See in Lawrence Homes
- Frost-heaved posts that throw latch alignment off. A gate that closed fine in October won’t latch by February because the post has shifted a quarter inch. We reset or weld-reinforce the post and realign the latch to hold through the next freeze cycle.
- Rotted below-grade posts on acreage driveways. Water sits at the base of wood posts through wet springs and winters, rotting the post below the soil line while it looks fine above ground. We cut out the rot, set new steel, and weld the hinge plates to the steel so it won’t happen again.
- Split rails and popped screws on aging wood gates. Summer humidity swells the wood, the hinges bind, and screws tear out. We reinforce with steel brackets and replace screws with through-bolts where the frame allows.
- Bent top rails and broken hinge welds from livestock pressure. Horses and cattle lean against wide farm gates waiting for feed, and eventually the top rail bows or the hinge weld fractures. We straighten what’s straightenable, weld what’s cracked, and reinforce weak points so the gate holds up to daily pressure.
Pricing for Gate Parts & Welding in Lawrence, IN
Here are honest numbers for Lawrence. Hinge replacement: $140-$320. Post replacement: $400-$900, higher if we’re breaking out a military-spec footing pad in the Harrison community. Rail repair: $150-$400 per rail. Custom welding: $120-$500. What moves the price is what we find underground, the weight of the gate, and whether the post can be reinforced or has to come out entirely. Every price is quoted and agreed before any work starts. The number we give you is the number on the invoice, not a starting point. We also run standing offers that don’t require haggling: $40 off any repair over $200, no trip charge inside Marion County, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans.
We Also Serve Cities Near Lawrence
While this page is for Lawrence residents, our crews regularly handle Gate Parts & Welding in Lawrence county neighbors too, including Cumberland, McCordsville, Broad Ripple, and Fishers. Same local knowledge, same upfront pricing, same 90-Day Done Right Promise. If your gate is an acreage gate on a county road or a subdivision gate off Pendleton Pike, the fix starts with a phone call.
Serving Lawrence, IN - Our Local Coverage Area
We’re based in the Lawrence area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Lawrence
Because frost heave keeps pushing it out of plumb, and pushing it back without addressing the footing or the below-grade condition just means it’ll lean again next winter. In Lawrence, the fix usually means digging out the old post base, checking for a military-spec footing if you’re near the Harrison community, and setting new steel in concrete that reaches below the frost line. Call (877) 610-2993 and we’ll tell you what’s actually under your post.
Yes, in most cases. We weld a new hinge plate directly onto the existing steel post, or onto a steel reinforcement sleeve we slide over a weakened wood post. Replacing the whole post is only necessary when the post is rotted below grade or shifted so far that welding to it means setting the gate crooked. We’ll show you the post before we quote.
Yes. We keep heavier hinge barrels, non-standard latch assemblies, and institutional-grade brackets in stock for Harrison community gates, because standard residential suppliers don’t carry them. When a Fort Ben Harrison-era gate needs a part, we’re usually the ones who have it on the truck, not three days out.
We install solar-powered openers. Most often we use Ghost Controls or Viking solar kits with one or two panels, sized to the gate’s weight and daily cycles. We rebuilt a sagging swing gate on a 46249 acreage driveway where the original hinge post had rotted below grade. Our crew cut out the old post, broke up a military-spec footing pad that ran 30 inches deep, welded a new steel post into the existing concrete, then rehung the gate with fresh hinges and a Ghost Controls solar opener running off two panels, no trenching to the house. That’s the standard approach: no trenching, no electrician run, no monthly power bill.
Yes, when the weld is done right and the weak point is reinforced. We don’t just lay a bead over the crack; we grind the area clean, weld the full joint, and add a gusset or plate where the stress concentrates. We’ve done enough farm gates in Lawrence to know where horses and cattle lean, and we weld for that pressure, not for looks. The repair carries the same 90-Day Done Right Promise as everything else we do.
Call Gatewood Fence & Gate for Gate Parts & Welding in Lawrence
If your Lawrence gate is sagging, refusing to latch, or leaning after every freeze, call (877) 610-2993. We answer live, we show up in the window we promise, and we quote the price before any work starts. Free estimates. No trip charge inside Marion County. The name is on the shop, and the shop is down the road.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Lawrence and central Indiana since 2001.