Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Lake Park
Most gate installation in Lake Park starts with one thing: salt air off the Lake Worth Lagoon eating through steel that was never spec’d for a marine environment. Hinges seize, posts rot at the base, and weld joints snap within two or three years instead of eight or ten. We fix that. Gatewood Fence & Gate has been welding gates on site since 2001, and when you call (877) 610-2993, a live person answers, not a voicemail system. We’ll tell you what’s actually wrong, what it costs, and when we’ll be there. The price is quoted and agreed before any work starts, so there are no surprises at the door.
Our Gate Parts & Welding team stocks marine-grade hardware and welds in your driveway, not in some far-off shop. If you’re in Lake Park, we’re close by and familiar with what your gate is up against.
Why Gatewood Fence & Gate Is Lake Park’s Preferred Gate Parts & Welding Company
Lake Park sits directly on the Intracoastal and immediately south of the Port of Palm Beach. That’s a beautiful spot to live, but it’s hard on metal. Bare steel hinges, springs, strike plates, and operator brackets corrode in one to three years here, not the eight to ten you’d see a few miles inland. We know this because Hal Gatewood has been looking at gate failures across Palm Beach County since 2001. When a gate sags, when a weld cracks, when a post rots through at the base, we already know what the salt did before we even pull up.
Hal’s name is on the shop, his address is published, and his license number is there for anyone to look up. That matters when you’ve been burned by a company that quoted one price on the phone and showed up with another. Every job we do in Lake Park carries our 90-Day Done Right Promise in writing. If it’s not done right, one call brings us back. No runaround, no fine print.
We serve the entire 33403 ZIP code, including the neighborhoods around Northlake Boulevard, Park Avenue, and the older streets east of US-1 down toward the lagoon. Calls are answered by a live person 24 hours a day, seven days a week. Not a dispatch queue, not a call center three states away. You’ll talk to someone who can actually tell you what’s going on with your gate.
For homeowners in Lake Park, that’s the difference between waiting three days for a callback and getting an answer right now.
Our Gate Parts & Welding Services in Lake Park
We repair and weld gates on site. The gate stays in your driveway. We don’t haul it off to a shop and bill you for transportation. Here’s what we handle most often in Lake Park:
Hinge Replacement
Salt air on the lagoon side of Lake Park seizes hinge pins fast. Bare steel hinges on aluminum frames set up galvanic corrosion, and within a year or two the pins won’t turn. We remove the old hinges, weld in stainless steel replacements, and set the gate so it swings clean without dragging. For houses even two or three blocks off the Intracoastal, this is the single most common repair we do. The surprise for homeowners is that the corrosion looks the same as it does on waterfront property. That’s Lake Park’s salt fog for you.
Post Replacement
When a gate sags, the problem is almost never in the middle of the panel. It’s in the hinge post. On mid-century Lake Park homes from the 1950s through the 1970s, those original posts are often eaten through at the base after decades of salt air and deferred maintenance. We cut out the rotted post, pour a proper footing, and set a hot-dip galvanized post with stainless hardware. Fix the panel without the post and you’ll fix it twice.
Rail Repair
Tubular steel slide gates along Northlake Boulevard and the commercial parcels nearby see heavy daily cycling, which wears rails and rollers faster than anything else. Add salt corrosion, and the bottom rail rusts through from the inside out. We cut out the damaged section, weld in a new rail, and re-align the rollers so the gate rolls true. On multi-family properties with slide gates, this repair keeps the gate from jamming at the worst possible time.
Custom Welding
Cracked frames, broken pickets, bent panels. If the metal can be welded, we weld it rather than replacing the whole gate. That’s our repair-first philosophy. We carry a mobile welder in the truck and do the work right there in your driveway. On ornamental iron gates around Lake Park, we regularly see cracked weld joints where the pickets meet the bottom rail. A quick weld, a rust passivation job, and a marine-grade paint over the area, and the gate keeps serving for years.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Lake Park
We service and source parts for most major gate brands you’ll find in Lake Park, including FAAC, BFT, Linear, and Viking gate motor and opener systems. When a control board fails or a limit switch burns out, we carry or can quickly get the right part for the opener you already have. We don’t tell you to replace a working operator because we don’t stock the board. And because we weld on site and stock our trucks with stainless and hot-dip galvanized hardware, turnaround for Lake Park customers is fast. The part goes in the same visit in most cases.
Common Gate Parts & Welding Problems We See in Lake Park Homes
Here’s what we keep finding on gates across the 33403 ZIP code:
- Galvanic corrosion between steel and aluminum. Original wrought-iron panels bolted to aluminum frames create a battery effect in salt air. Hinge pins seize, weld joints snap, and brackets crumble within months.
- Rotted hinge posts that fool the eye. The post looks fine at waist height. Down at the base, below the soil line, it’s eaten through. The gate sags because the post is gone, not because the panel bent.
- Fried operator boards after hurricanes. Palm Beach County’s storm season sends power surges through gate openers. The gate looks fine physically, but the board is dead. We diagnose it before you spend money on a whole new operator when all you need is a board.
- Rust-bloomed bottom rails on slide gates. Slide gates along Northlake Boulevard corrode from the inside where water and salt collect. The rail looks OK on top, but it’s paper-thin underneath. We cut it out and weld in new steel.
Pricing for Gate Parts & Welding in Lake Park, FL
Here’s what gate work costs in Lake Park right now. Hinge replacement on a typical single swing gate runs $180 to $340, depending on whether we’re replacing one hinge or the full set in stainless. Post replacement with a new footing runs $450 to $850 per post. Rail repair on a tubular slide gate runs $220 to $500, depending on how much rail needs to be cut out and replaced. Custom welding for cracked frames or broken pickets runs $150 to $400 per repair, based on the length of the weld and the prep work involved.
Two things change the price on any job: how bad the corrosion has gotten, and whether the gate was ever installed with marine-grade hardware to begin with. If we catch it early, you spend less. Every quote is written down and agreed before we pick up a tool. There’s no trip charge inside the county, $40 off any repair over $200, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 and we’ll give you an exact number before any work begins.
On a 1960s swing gate near Northlake Boulevard, we found the hinge post eaten through at the base from years of salt air while the ornamental iron panel looked almost new. We cut out the rotted post, poured a new post footing, and welded in a hot-dip galvanized post with stainless steel hinges and latch. The owner was surprised the house sat three blocks from the Intracoastal and still needed marine-grade fixes. That’s Lake Park. The salt fog off the lagoon doesn’t care how far you are from the water. It reaches everyone in the 33403 ZIP code.
Because Lake Park is one of the smallest, densest municipalities in Palm Beach County, there’s no undeveloped buffer between the lagoon and the housing. Salt air blankets properties a block or two inland as thoroughly as it blankets waterfront homes. When we inspect gate access control in Lake Park, we treat every call as a corrosion-first diagnosis. Every replacement part gets specified in stainless steel, marine-grade aluminum, or hot-dip galvanized steel. No painted mild steel, no bare hardware. Those fail in two years here, and we’re not going to do a job that rots out before the invoice clears.
We Also Serve Cities Near Lake Park
If you’re in Riviera Beach, North Palm Beach, Palm Beach Gardens, or Palm Beach, you face the same salt air environment as Lake Park, just a few miles down the road. We service the whole north county corridor, so if you’re near the lagoon or the Port of Palm Beach, the same marine-grade spec applies. Calls from those areas get the same live-person answer and the same Lake Park standard of work.
Serving Lake Park, FL - Our Local Coverage Area
We’re based in the Lake Park area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Lake Park
Yes. Salt fog from the Lake Worth Lagoon reaches every street in Lake Park, not just waterfront property. Bare steel hinges on an aluminum or steel gate set up galvanic corrosion and seize within one to three years. Stainless hinges and hot-dip galvanized brackets are the minimum spec for any gate in the 33403 ZIP code. Call (877) 610-2993 for an exact quote on stainless hinge replacement. Estimates are free.
The board almost certainly fried from a power surge, not from physical damage. Palm Beach County storm activity sends spikes through the electrical service, and unsealed gate operator boards take the hit. The gate structure looks fine, but the board is dead. We diagnose it with a meter before recommending anything, so you don’t pay for a whole operator when a replacement board fixes the problem. Call (877) 610-2993 and we’ll tell you what’s actually dead and what it costs.
Almost certainly the hinge post. On Lake Park’s mid-century homes, the post rots at the base while the panel stays straight. A gate sags in the hinge post, not in the middle. We confirm it on site, cut out the post, pour a new footing, and set a hot-dip galvanized post with stainless hinges. If the panel is also cracked, we weld that too. Free estimates, no trip charge inside the county.
Cut out the rotted section and weld in a new rail, then re-align the rollers. Patching over rust never lasts, especially in Lake Park where salt air keeps eating the steel from the inside out. We do the cut, weld, and realignment on site. Most rail repairs run $220 to $500 depending on how much rail has to go. Call (877) 610-2993 and we’ll give you a written number before we start.
Yes, and that’s what we’d rather do. If the metal around the crack is sound, we weld the crack, grind it smooth, and treat the area against further corrosion. If the frame is rotted through in multiple spots, replacement may be the honest call, but we never recommend a new gate when a weld will hold. Custom welding repairs in Lake Park run $150 to $400 depending on the weld length. Call (877) 610-2993 for a free estimate.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Lake Park and Palm Beach County since 2001.