Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Kirkland
Gate parts and welding in Kirkland usually come down to one question: can the post be saved, or does it need to come out? Most of the time, the gate itself is fine. The hinge post has rotted, shifted, or corroded where the stainless meets the steel, and that’s what’s dragging the whole panel out of true. We fix the post in place, rebuild the hinge, and weld on site so your gate never leaves your driveway. If you’re in Kirkland and the gate is dragging, sagging, or swinging loose, call us at (877) 610-2993. Hal or one of his crew will pick up.
Why Gatewood Fence & Gate Is Kirkland’s Preferred Gate Parts & Welding Company
We’ve been at this since 2001, and our Gate Parts & Welding team has seen every failure mode Kirkland can throw at an automated gate. The lake humidity eats control boards. The clay in Bridle Trails heaves posts out of plumb. The shared driveways off Juanita Drive don’t leave room to swing a wide gate, so slide gates take the abuse instead. None of it surprises us anymore, which means we show up knowing what we’re looking for.
Hal Gatewood’s name is on the shop and on every invoice. That’s not marketing, it’s how the business works. When a Kirkland homeowner calls, they get a live person, not a robot or a routing queue. We answer 24/7, and if Hal says he’ll be there Tuesday between nine and noon, he’s there Tuesday between nine and noon. That’s the oldest accountability there is.
Every job we do in Kirkland carries the 90-Day Done Right Promise, in writing. If the gate sags again or the weld cracks, one call brings us back. No runaround, no fine print. We also back our work with a free second opinion on any written estimate, no trip charge inside King County, and a permanent 10% discount for seniors and veterans.
Our Gate Parts & Welding Services in Kirkland
Hinge Replacement in Kirkland
Hinge replacement in Kirkland is rarely just a hinge swap. On the older ranch homes in the 98033, we regularly find the original hinge hardware was sized for a light wooden gate, then somebody hung a heavy iron gate during a 2000s renovation without upgrading the pivot. The hinge wears, the gate sags, and the latch stops lining up. We replace the hinge with a properly rated one and check the post while we’re at it, because a new hinge on a leaning post fixes nothing.
Post Replacement in Kirkland
A gate sags in the hinge post, not in the middle, and that’s where we start. Kirkland post replacement usually means digging out an undersized footing, not just swapping the post. In Bridle Trails especially, the clay-heavy glacial soil holds water through the winter and expands, slowly pushing the post out of plumb. We re-plumb the post, pour a deeper concrete footing with proper drainage, and add a steel kicker plate where the design calls for it. Fix the post and the gate hangs straight.
Rail Repair in Kirkland
Rail repair covers the horizontal members that hold the gate panel together. On Kirkland’s lakefront properties, the bottom rail is the first thing to go because it sits closest to the damp ground and catches splashback from Lake Washington moisture. We weld cracked steel rails on site, sister rotted wood rails, and straighten bowed aluminum before it binds against the latch post.
Custom Welding in Kirkland
Custom welding is where we spend a lot of our time in Kirkland, because this city has an unusually high concentration of custom iron and steel driveway gates. A lot of them were built for specific openings, with non-standard hinge placements and operators that don’t mount the way the manual says. We weld on site, in the driveway, usually same day. If a bracket is cracked or a post cap rusted through, we cut, fit, and weld the repair without hauling the gate to a shop.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Kirkland
We’re certified to service nine major gate brands, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. For Kirkland homeowners, the two we see most are LiftMaster on newer installations and Viking on older custom gates, especially around Bridle Trails and the lakefront. We keep common parts and circuit boards for those brands stocked in our shop, so most repairs don’t wait on a parts order. Whether you have a Linear swing arm, a Ghost Controls slide operator, or a DoorKing commercial unit on a shared driveway, we can get it running again without swapping equipment that doesn’t need replacing.
Common Gate Parts & Welding Problems We See in Kirkland Homes
- Leaning hinge posts on clay soil. In Bridle Trails and other parts of Kirkland with glacial clay, the ground swells and shifts seasonally. The post rotates, the gate drags, and the latch misses. Replacing the hinge won’t fix a rotated post, the post has to come out and get re-set.
- Galvanic corrosion at the hinge post. When stainless steel bolts meet uncoated steel leaves in Kirkland’s persistent humidity, the two metals react and pit within five to seven years. The gate sags, binds against the latch plate, and eventually won’t close at all.
- Seized slide gate rollers. Lake Washington moisture mixes with road grit in the track channel and locks up the rollers. The rack and pinion drag, the operator’s obstruction sensor trips, and the gate stops halfway across the driveway during the morning commute.
- Swollen wooden gates that won’t latch. Kirkland’s roughly 38 inches of annual rain keeps wood gates in a near-constant state of swelling. A gate that latched fine in August won’t close in February without shaving the panel or resetting the latch.
These aren’t generic gate problems. They’re the specific ways Kirkland’s climate and soil beat up on gate hardware, and we see them every week.
Pricing for Gate Parts & Welding in Kirkland, WA
Here’s what you can expect in Kirkland. A basic hinge replacement runs $120 to $250, depending on the gate’s weight and how much of the existing hardware can be reused. Post replacement ranges from $400 to $900 when the footing is sound, and $900 to $1,600 when we’re digging out an undersized footing and re-pouring with deeper concrete. Custom welding jobs typically run $150 to $450 for a single bracket, hinge leaf, or crack repair, and $500 to $1,200 for structural work like a bent top rail or a cracked frame. Slide gate roller replacement runs $180 to $380 per roller.
What changes the price? Gate weight, post condition, access to the footing, and whether the existing concrete can be saved. We quote the exact number before any work starts, and that number is the number. Not an estimate that drifts upward when the invoice shows up. Any repair over $200 gets $40 off, and there’s no trip charge inside the county. Call (877) 610-2993 and we’ll give you a free written quote.
We Also Serve Cities Near Kirkland
We work across the Eastside. In addition to Kirkland, we serve Inglewood-Finn Hill, Kingsgate, Kenmore, and Redmond. Same crew, same live person on the phone, same 90-Day Done Right Promise. Scheduling is coordinated from our Seattle office, but the people who show up at your gate are local to the Eastside and know the area.
Serving Kirkland, WA - Our Local Coverage Area
We’re based in the Kirkland area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Kirkland
Because the post is rotating in the footing, not the hinge failing. In Kirkland’s clay-heavy soil, particularly in Bridle Trails, the ground swells with winter moisture and shifts the post out of plumb. A new hinge just transfers the load to a post that’s already moving. The fix is to dig out the old footing, re-plumb the post, and pour deeper concrete with proper drainage. We do that work in Kirkland regularly. Call (877) 610-2993 and we’ll take a look.
Lake Washington keeps the air humid year-round, and that moisture finds its way into the operator housing and control board enclosure. Over time, the condensation corrodes solder joints and contacts on the board, and the operator starts behaving erratically, intermittent opening, sensor faults, or complete failure. We stock replacement boards for the major brands and install them same day in most Kirkland cases.
Yes. We can replace the rack, the pinion gear, or both without pulling the gate off its track. On Kirkland slide gates, the usual problem is a seized roller forcing the rack to drag, which then wears the pinion. We fix the roller first, then replace the rack section or pinion as needed. It’s done in the driveway, usually in one visit.
Put it in manual release and keep it open until we arrive. The safety edge or photo eye has failed, which means the gate no longer reverses when it hits an obstruction. That’s not a repair to put off, a gate that closes on a car will close on a person. We treat that as a priority call in Kirkland and answer the phone around the clock at (877) 610-2993.
Kirkland’s persistent humidity, roughly 38 inches of rain a year plus Lake Washington moisture, keeps wood gates absorbing water through the winter. The panel swells, the latch plate moves, and the gate won’t close without forcing it. We typically shave the panel, reset the latch plate, seal the end grain, and adjust the hinges so the gate works through the full seasonal cycle instead of just in dry weather.
If your gate is dragging, sagging, or won’t latch in Kirkland, call (877) 610-2993. We’ll give you an honest assessment and a written price before any work starts. Hal Gatewood’s name is on the shop, and the shop is down the road.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Kirkland since 2001.