Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Kennesaw
If you’re managing a subdivision entry gate in Kennesaw that’s sagging, grinding, or failing to close, Hal Gatewood has likely seen your exact problem before. We focus on repairing the gate in place, welding on site, and replacing only what’s actually worn out. Most calls from the 30144 and 30152 ZIP codes get someone out the same day, and you’ll get a straight price before any torch gets lit. Call (877) 610-2993 and you’ll reach a live person, not a voicemail tree.
Why Gatewood Fence & Gate Is Kennesaw’s Preferred Gate Parts & Welding Company
Hal Gatewood has been fixing gates since 2001, and he puts his name on the shop and on every invoice. In a town like Kennesaw, where the subdivisions off Stilesboro Road and Chastain Meadows Parkway are full of 1990s entry gates held together by patchwork repairs from three different vendors, that accountability matters. We answer the phone around the clock, not with a call center, but with a person who knows what a loop detector is and why yours keeps false-triggering.
Kennesaw homeowners and HOA boards call us because we show up in the window we promised and we don’t quote one price on the phone and another at the gate. The 90-Day Done Right Promise is written on every job. If it’s not right, we come back and make it right. No fine print, no runaround. That’s how an owner-operated shop keeps a reputation in a community where the same faces show up at the hardware store on Barrett Parkway week after week.
We’re certified to service nine major gate brands including Linear, Viking, Ghost Controls, and DoorKing, but honestly, half the calls in Kennesaw are for operators so old the original manufacturer doesn’t support them anymore. That’s where on-site welding and a repair-first mindset matter. We don’t tell you to replace a $6,000 community gate because a hinge post has pulled out of plumb. We dig the post, weld the reinforcement, and get the gate closing square again.
Our Gate Parts & Welding Services in Kennesaw
Here’s what most Kennesaw calls actually turn out to be. Not general handyman work. Specific mechanical and structural failures on aging subdivision gates.
Hinge Replacement
Swing gates in Kennesaw’s 1988-2005 subdivisions hang on original hinges that have now seen 25 to 35 Georgia summers. Humid air eats steel, and the red clay under the hinge post swells and shrinks with every rain, slowly pulling posts out of alignment. A gate that drags at the latch post is almost always a hinge post problem, not a hinge problem. We replace the hinge, yes, but we fix the post geometry first. Otherwise you’ll be back in the same spot after the next wet season.
Post Replacement
Kennesaw sits on Piedmont red clay that behaves like a slow-moving material science experiment under your gate post. Wet winters swell it, dry summers shrink it, and forty years of that cycle heaves steel posts out of plumb by an inch or more. We dig out the old footing, set the new post below the frost line and deep enough to resist clay movement, and weld any necessary reinforcement plates before the operator goes back on. In the subdivisions off Stilesboro Road, we do this almost weekly during the rainy months.
Rail Repair
Slide gates from the 1990s and early 2000s were built with rails and racks that take a beating as posts shift and rollers wear. We see bent rails, chewed-up rack teeth, and gates that jump track after heavy rain softens the ground under the rollers. On-site welding means we can cut out a bad rail section, weld in new stock, and have the gate running true the same day. Hauling a 14-foot slide gate back to a shop is a week-long project for most companies. We’d rather fix it in your driveway or at the community entrance where it belongs.
Custom Welding
Older Kennesaw subdivision gates often have custom ironwork - a finial pattern, a scroll detail, a particular picket spacing - that no catalog part matches anymore. We weld on site and can fabricate replacement sections that match the original design closely enough that the HOA architectural committee never gets a reason to complain. We’ve rebuilt gate frames, repaired rusted-through hinge stiles, and reinforced cracked post caps on entryways that were installed before the neighborhood even had a management company.
When you call about any of this, the price is quoted and agreed to before we start. No surprises at the gate.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Kennesaw
Most Kennesaw communities built from the late 1980s onward used a handful of operator brands, and we keep parts on the truck for the common ones. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That said, the original 1990s slide-gate motors in many 30144 and 30152 subdivisions are long out of production, which is why our Gate Parts & Welding work often involves retrofitting new operators onto old iron rather than swapping like-for-like. We stock universal mounting brackets, safety photocells, loop detectors, and hinge hardware locally so we’re not waiting on a supply house to finish your repair.
Common Gate Parts & Welding Problems We See in Kennesaw Homes
- Heaving hinge posts. Kennesaw’s red clay expands when wet and contracts when dry, so posts set in poor or shallow footings lean over time. A swing gate that binds at the latch post or drags the ground in one spot is usually heave, not hinge wear. We fix the post, not just the hinge.
- Rust-corrupted steel. Humid subtropical summers are harder on gate hardware than Kennesaw’s mild winters. We find rusted-out hinge barrels, corroded latch bars, and pitted electrical contacts on slide gates that look fine on the outside but fail intermittently.
- Mismatched control boards. Communities that went years without a consistent maintenance vendor often have 1990s operators retrofitted with whatever board fit the mounting hole. That creates safety photocell misalignment, loop detector logic errors, and gates that reverse for no reason. We custom-fabricate mounting plates to get geometry back where it belongs.
- Obsolete keypads and intercoms. Original equipment from the 1990s is mostly gone, and replacements don’t always fit the pedestals. We weld adapter plates and trim plates on site so the new keypad sits flush and works with the existing wiring, without tearing up the brick column.
Pricing for Gate Parts & Welding in Kennesaw, GA
Kennesaw’s market is a mix of large HOA slide gates and smaller residential driveway swing gates, so here’s what we actually see. Hinge replacement on a residential swing gate typically runs $180-$340 per hinge depending on the post condition and whether we need to dig and re-set the footing. Post replacement with new concrete and welded reinforcement plates usually runs $580-$980 per post for a standard 4×4 or 6×6 steel post. Custom welding work like rail section repair or crack repair runs $120-$220 per weld point, with most jobs including two or three points. A full slide gate rail and roller rebuild for a community entrance can run $1,400-$3,200 depending on the gate length and how much of the original rack is salvageable. You’ll get a written price before we start, and you’ll pay that price when job is done. Call (877) 610-2993 and Hal will walk you through what your specific gate needs. Free estimates, no trip charge inside the county, and $40 off any repair over $200.
We Also Serve Cities Near Kennesaw
Our Gate Parts & Welding in Kennesaw coverage extends to the surrounding area, including Acworth, Marietta, Powder Springs, and Fair Oaks. If you’re managing a community gate or your own driveway gate in one of those cities, the same crew, the same pricing, and the same 90-Day Done Right Promise apply. Dispatch and scheduling are coordinated from our Atlanta office, and crews serve Kennesaw locally every day.
Serving Kennesaw, GA - Our Local Coverage Area
We’re based in the Kennesaw area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Kennesaw
Yes, in most Kennesaw subdivisions governed by an HOA, you need architectural review before any change to gate style, height, finish, or post configuration. Even a repair that changes the look of the gate, like adding a welded reinforcement plate that’s visible from the street, can trigger a covenant complaint. We can prepare a simple written description and material spec for your HOA or management company before work starts. Call (877) 610-2993 if you need help figuring out what your committee will ask for.
Because the hinge post is moving, not the hinge. Kennesaw’s red clay heaves seasonally and gradually pushes posts out of plumb, so replacing the hinge bracket without correcting the post just moves the same problem to a new bracket. We dig the post, re-set or reinforce the footing, weld any needed plate, and then install the new hinge. That order of operations is what stops the sag from coming back.
Yes, we fabricate and weld on site and can match most scrollwork, finial patterns, and picket details from the 1990s and early 2000s. We’ve rebuilt enough Kennesaw entry gates to know the common styles, and we’ll match the material thickness and finish so the repair doesn’t look like a patch. For unusual custom work, we’ll show you a sample or drawing before we cut anything.
First we check the roller alignment and the post holding the track. Rain softens the red clay, the post shifts, and the track drifts out of line. We re-set the post if it’s moved, then align and reinforce the rail so the gate runs true again. A gate that jumps track is also a safety issue - it can fall on a car or a person. Call (877) 610-2993 and we’ll get it stable the same day.
Yes. Any time we work on a gate operator or its mounting hardware, we test the UL 325 entrapment protection - the safety photocells, the edge sensors, and the reversing function - before we leave. A welded rail or a straight hinge post does no good if the operator can close on a kid or a delivery driver. If the photocells are obsolete or misaligned, we’ll tell you what it costs to bring them current, and the price is agreed before we do the work.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Kennesaw since 2001.