Gate Repair in Kennedale - Same-Day Repair, Priced Before We Start

Gate Repair in Kennedale, TX

If your gate is dragging, sagging, or the opener just hums and won’t move the panel, most Kennedale homeowners pay between $150 and $650 for repair, and we can usually get someone out within 24 hours. Kennedale’s mix of 1950s ranch acreage and newer subdivisions means we’re fixing everything from heavy pipe-rail pasture gates to modern ornamental iron systems, often on the same black clay that keeps shifting the posts underneath them. Call us at (877) 610-2993 and a live person answers, any hour.

Call (877) 610-2993

Why Kennedale Homes Are Different

Kennedale sits on the Blackland Prairie, and the black clay under these lots is the real story behind most gate failures here. The soil expands when it rains and contracts when it dries, which means gate posts that were perfectly plumb in spring can be leaning a half inch by September. That constant swell and shrink is why the older pipe-rail ranch gates on the south and east edges of town walk their posts sideways every few years. Those gates were set directly in the dirt without concrete footings decades ago.

Summer hits differently here, too. Temperatures over 100°F expand steel gate frames and stress weld joints, while wooden farm gates from the old rural homesteads warp and crack in the heat. The housing stock splits cleanly: legacy acreage properties with half-acre to 10-plus-acre lots dating to the 1950s through 1980s, and suburban tract development from the 1990s through 2010s. The older places have gates that have never been upgraded; the newer ones have automated ornamental iron that still has to survive the same clay and heat.

Kennedale has long marketed itself as an equestrian-friendly enclave within the DFW Metroplex. City ordinances permit horses on qualifying acreage lots, and a notable share of properties combine pasture perimeters, pipe-rail livestock entries, and round-pen gates alongside conventional residential driveway gates. Gate repair here means our crew must be fluent in both heavy agricultural hardware and modern automated ornamental iron systems, a dual skill set that a purely suburban neighbor rarely demands.

Gate Repair in Kennedale

Most gate repairs in Kennedale run between $150 and $650, and we’re usually on-site within 24 to 48 hours. On the acreage lots that define this town, a busted gate can mean livestock wandering toward New Hope Road and a driveway entrance that no longer does its job. We fix the gate in your driveway rather than hauling it off, and we weld on site so the repair is done same day in most cases. Gate Repair is what we’ve done since 2001, and Hal still walks the jobs where the post work is tricky.

Electric Gate Repair

An electric gate in Kennedale may be anything from a solar-powered opener on a pipe-rail entrance to a modern keypad and sensor system on a new subdivision home. We chase down power issues, bad photo eyes, dead keypads, and wiring that’s degraded from a decade of North Texas sun. When an electric gate starts opening halfway and reversing, the sensor or limit switch is usually the culprit, and we can fix it without replacing the whole system. Electric gate repairs in Kennedale, including new photo eyes, keypad swaps, or limit switch replacement, usually fall between $150 and $450.

Hinge and Post Repair

A gate sags in the hinge post, not in the middle, and that’s where we start. Kennedale’s Blackland Prairie soil heaves and shrinks with every wet-dry cycle, which slowly levers posts out of plumb. We re-set posts in concrete, weld on new heavy-duty hinges, and re-hang the gate so it swings true. A typical hinge and post repair runs $180 to $400, depending on whether we’re re-concreting the post or just adjusting the existing footing. Fix the panel without the post and you’ll fix it twice.

On-Site Weld Repair

The 1950s-through-1980s acreage homesteads around 76060 still use heavy steel pipe gates that have been out in Texas heat for decades. Weld joints crack, bottom rails rust through, and hinges seize. We weld on-site, so the gate stays in your driveway and the repair is done same day in most cases. Weld repairs and rust patches run $120 to $350. On older Kennedale acreage parcels toward the southern and eastern edges, where ranch gates were set directly into the clay without concrete footings, we expect to re-concrete the post before any alignment work even begins.

Can you come to Kennedale the same day?

We can reach most Kennedale homes within 24 to 48 hours for non-emergency repairs, and emergency calls, like a gate stuck open with livestock at risk, often get someone out same day. Call (877) 610-2993 and tell us what the gate is doing; we’ll give you a straight answer on timing, not a vague window.

How much does gate repair cost in Kennedale?

Most electrical repairs run $150 to $450, hinge and post work lands at $180 to $400, and a full opener replacement can reach $600 to $1,800 depending on the gate’s weight. The bigger variable isn’t the city line, it’s the gate type. The quote is set before any work starts, and that number doesn’t move. Call (877) 610-2993 for an exact quote - estimates are free.

Gate Installation in Kennedale

Gate installation in Kennedale isn’t a one-size-fits-all job. A driveway gate on a half-acre tract home off Mansfield Highway needs something different than a 16-foot pipe-rail entry on a five-acre horse property off Dick Price Road. We excavate below the active soil line and pour concrete footings sized for the gate’s weight and swing span, because on Kennedale’s expansive clay, a post set shallow gets worked loose within two years. Gate Installation quotes are always in writing before any work starts.

Driveway and Double Gates

Most Kennedale driveway gates fall into two camps: ornamental iron or aluminum on the newer subdivisions, and heavier steel or pipe-rail on the older acreage lots. Double gates are the standard entry for horse properties and rural driveways, but two leaves double the hinge load and alignment problems if the posts shift. We’ve reset and re-concreted dozens of double gate posts across Kennedale where the clay heave walked the hinge posts out of plumb. A new single driveway gate installation in Kennedale typically runs $2,800 to $5,500, while double swing gate installs on acreage lots, with new post footings below the clay line and a heavy-duty opener, generally land between $6,500 and $12,000.

Sliding and Swing Gates

Sliding gates work well on Kennedale properties where the driveway slopes or where a swing gate would block the parking area. The track and foundation have to be dead level, and on clay soil that means a reinforced concrete pad with proper drainage so the track doesn’t heave and bind. Swing gates live or die by their hinge posts; we bury posts deep, below the expansive clay line, and use concrete footings with rebar on anything wider than 8 feet. For a 20-foot pipe-rail swing gate on an equestrian property, we step up to a heavy-duty arm opener with battery backup because a gate that size shouldn’t depend on a residential-grade motor.

Solar Opener Systems

A solar kit that powers a lightweight picket gate will struggle with a 16-foot pipe-rail gate, especially on a tree-shaded long driveway. We size the panel, battery, and operator for the gate’s actual weight and the site’s sun exposure, not a catalog chart. A solar gate opener with keypad entry and safety photocells costs roughly $1,800 to $3,800, including the panel, battery, and installation. If we’re replacing a gate and the posts are still plumb and solid, you’ll save that footing work.

Why does Kennedale’s black clay cause new gate posts to lean within two years?

Kennedale sits on Blackland Prairie soil, a highly expansive clay that swells when wet and shrinks and cracks when dry. Posts set shallow in that clay get worked loose by the movement. We excavate post holes below the active soil line and pour concrete footings with rebar so the post anchors into stable ground. That’s standard on every gate we install.

Can I run a heavy-duty automatic opener on a solar panel for my acreage gate?

Yes, provided the panel, battery, and operator are sized for the gate’s weight and the site’s actual sun exposure. We’ve installed solar systems on acreage driveways across Kennedale where running mains power wasn’t practical, and we’d rather over-build the solar side than leave you with a gate that quits at dusk. Call (877) 610-2993 for a free measure and written price.

Gate Motor & Opener in Kennedale

Gate motor and opener trouble in Kennedale usually starts long before the motor itself quits. On the acreage lots that define this town, shifting Blackland Prairie clay moves hinge posts out of plumb season after season, and an opener that worked fine in March binds hard by August. We fix the whole system, not just the box on the post. Gate Motor & Opener service from Hal’s crew means checking alignment before we sell you a motor you don’t need.

Motor Repair and Replacement

When a Kennedale gate motor hums but doesn’t move, binds mid-swing, or trips its force settings every afternoon, the first thing we check is post alignment. Summer heat expands the steel frame; shifting clay tilts the post. Both make the opener work against itself until something gives. We repair, rebuild, and replace motors on all nine brands we service, and we do it in the driveway. A typical standalone swing or slide gate motor repair runs $280 to $480 including parts when the post is sound. If the hinge posts need re-plumbing and re-concreting, expect $650 to $1,200 for the full job with the opener on top.

Linear and Slide Motors

Linear arm operators are common on the newer automatic gates in Kennedale’s 1990s and 2000s subdivisions, and they fail in predictable ways here: internal gears strip after years of fighting clay-shifted hinges, and limit switches drift as the post moves. We carry Linear parts and know the brand well enough to tell you honestly whether a repair buys you another five years or whether the money’s better spent on a different operator. Many Kennedale acreage gates are built as sliders, and they live or die by the condition of the track. On gravel or dirt approaches off Dick Price Road or Rendon Road, the track collects debris, the wheels flatten, and the motor strains until it burns out. We service slide operators from Viking, Elite, and DoorKing, and we re-level the track when needed so the new motor isn’t inheriting the old problem.

Solar and Battery Backup

Kennedale summers cook solar batteries, and undersized panels on shaded acreage entrances can’t keep up with wide farm gates cycling several times a day. We right-size the panel, the battery bank, and the operator duty cycle so the gate keeps working past sundown. A new solar-ready operator with battery backup and proper panel sizing on an acreage gate typically lands between $1,400 and $2,600 finished. On solar-powered gates, the battery bank doubles as the outage reserve, which matters more here because rural feeders come back last after a storm.

Why does my Kennedale gate motor work in spring but bind in summer?

Summer heat expands the metal gate frame, and it often binds against hardware that was close-tolerance all winter. But the bigger culprit in Kennedale is the clay: spring rains swell the soil, summer drought shrinks it, and the hinge post creeps out of plumb. By July the gate is fighting its own geometry, and the motor draw spikes until the force sensor trips. We check post alignment before anything else.

Do I need entrapment protection on my Kennedale automatic gate?

Yes. Any automatic gate operator requires entrapment protection under UL 325: photo eyes, contact edges, or both, depending on the gate type and risk. On Kennedale acreage gates with livestock, we also recommend a monitored loop or edge so a horse or child near the gate can’t get caught. We include this in every motor install and test it before we leave. Call (877) 610-2993 to schedule.

Gate Access Control in Kennedale

Gate access control in Kennedale means retrofitting keypads, card readers, and phone entry onto gates that were often built decades before anyone imagined automated security. We know 76060’s mix of 1970s pipe-rail ranch entries and newer subdivision gates. When a control board drops its programming or a keypad quits after a rain, we’re the ones who answer the phone - a live person, any hour. Gate Access Control from Hal’s shop means the system gets programmed and tested before we leave, with a written cheat sheet in your hand.

Keypad and Phone Entry

Keypad entry systems in Kennedale fail for a reason most companies miss: the hinge post moved. On Blackland Prairie clay, a post set without concrete heaves with every wet-dry cycle. That pulls the gate off the striker, and suddenly your keypad works intermittently because the latch switch never signals a closed gate. We start with the post, then wire the keypad. A new keypad install in Kennedale runs $450 to $900 including the controller and wiring, depending on whether we’re retrofitting an old operator or starting fresh. Phone entry and card readers are popular for properties with multiple users, and a system with a gate strike starts around $800 and goes to $2,200 depending on the gate.

Video Intercom

Video intercom is what most Kennedale homeowners want when they’re tired of walking to the gate to see who’s there. On acreage properties near the southern edge, that walk can be a quarter-mile. We install wired and wireless video intercoms that tie into your phone, so you can see and talk to whoever’s at the gate from the house or from anywhere. Expect to pay $1,200 to $2,800 in Kennedale for a quality video intercom paired with gate release. Older operators sometimes need a relay added, which we quote before any work starts.

Smart Access Retrofits

Smart access means controlling your gate from your phone. For a 1980s homestead off New Hope Road, that doesn’t mean tearing everything out. It means adding a smart controller to an existing motor, setting up app access, and checking that the gate’s entrapment protection still tests clean under UL 325. We program the system, walk you through it, and leave a written cheat sheet. Smart access retrofits in Kennedale run $600 to $1,400 on average. Full automation of a previously manual pipe-rail gate, including posts, operator, and keypad, starts at $3,500 and can reach $7,000 if we’re dealing with a long drive and heavy gate.

Why does my older Kennedale swing gate keypad work sometimes but not others?

In almost every case we see, the keypad itself is fine. The hinge post has moved in the Blackland clay, the gate no longer strikes true, and the latch switch either doesn’t engage or engages at the wrong point. The keypad can’t confirm the gate is closed, so it drops the signal intermittently. We re-plumb the post, re-concrete it, and then re-test the keypad. Call (877) 610-2993 and we’ll come sort it out.

Can I retrofit a card reader onto a 1980s pipe-rail ranch gate that was never automated?

Yes. We do this regularly on acreage parcels around Kennedale’s southern and eastern edges. First we address the post - most of those 1980s pipe gates were set into clay without concrete, so the post must be re-plumbed and re-concreted or nothing we add will stay aligned. Then we add a gate strike and card reader or phone entry controller. The gate doesn’t need a full operator; we can automate just the latch if that’s what you need.

Gate Parts & Welding in Kennedale

If you live in Kennedale with a sagging pipe-rail gate, a hinge that’s pulled loose from the post, or a latch that no longer lines up, you already know the frustration. Gate parts and welding here isn’t a weekend project when the gate weighs several hundred pounds and the post has shifted in clay. We come to your property, fix it in your driveway, and stand behind the weld with the 90-Day Done Right Promise. Gate Parts & Welding is where Hal started, and it’s still the core of what we do.

Hinge and Post Replacement

Hinge replacement in Kennedale usually starts with a diagnosis the hinge didn’t cause. The highly expansive black clay soil heaves and shrinks with every wet-dry cycle, and a hinge post that’s moved half an inch out of plumb makes the gate bind at the latch no matter how new the hinge is. We weld replacement hinges onto the existing frame, but only after confirming the post is still set true. A basic hinge replacement with on-site welding typically runs $180 to $340, depending on the gate’s weight and whether the post needs re-plumbing first. Post replacement on an acreage pipe-rail gate usually falls between $450 and $800, including concrete footing and welded hinge remounts.

Rail Repair and Custom Welding

Rails on Kennedale’s pipe-rail and tubular steel gates take abuse from livestock, trailers, and the summer heat. Metal expands in 100°F weather and contracts at night, and after enough cycles the welds at the rail joints crack. We cut out the failed section, weld new rail in place, and grind it clean so it looks like it grew there. Rail repair or a custom weld job on a round-pen gate can run $150 to $500 depending on the length and gauge of the steel. Kennedale’s equestrian zoning means a fair number of properties need custom work that has nothing to do with a standard residential swing gate: round-pen gates, pipe-rail livestock entries, drop-rod latch mounts, heavy weld-on hinges for 2-inch tube steel. We weld those on site, built to the span and weight of your gate rather than whatever came in a box.

Opener Mount and Hardware Fixes

When a metal gate frame expands in the heat, the geometry shifts just enough that a solar opener arm binds mid-stroke. Often the fix is a combination of hinge realignment and re-welding the arm mount plate. If a solar opener arm needs a reinforced mount plate on a wide farm gate, we fabricate that too. The name is on the shop, and the shop is down the road - that is the oldest accountability there is. A full custom gate fabrication for an equestrian entry starts around $900 and goes up with the span.

Why do my pipe-rail gate posts keep leaning sideways in Kennedale’s clay soil?

The Blackland Prairie clay under Kennedale expands and contracts dramatically with moisture. Posts set directly into that clay, without a proper concrete footing, get walked sideways over a few wet-dry cycles. The only permanent fix is to pull the post, re-plumb it, and set a new footing that resists the movement before re-welding the hinges. A hinge swap alone won’t hold. Call (877) 610-2993 and we’ll assess it for free.

Can you weld a new hinge onto my existing swing gate without replacing the whole frame?

Yes, and that’s most of our hinge work in Kennedale. Unless the frame itself is rusted through or bent, we weld replacement weld-on hinges directly to the existing gate. But we check the post first. If the post has heaved in the clay, a new hinge on a leaning post still leaves a gate that binds. We’ll tell you straight what needs doing before any work starts.

Brands We Service in Kennedale

We’re certified to service nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We stock common parts for FAAC, BFT, and Viking locally, which means most Kennedale repairs don’t wait on shipping. If your operator is one of these brands and it’s acting up, call (877) 610-2993 - chances are we’ve seen the exact failure before. our brands

Pricing for Gate Repair in Kennedale, TX

Neighborhoods We Serve in Kennedale

We run calls all across the 76060 ZIP, from the older ranch-style lots on the south side to newer subdivisions off Kennedale Parkway. Typical response time for the Kennedale area is same day or next day, and we’ll always give you a straight answer about when we’ll arrive.

• Kennedale TownCenter
• Far West Kennedale
• Kennedale Parkway subdivisions
• Sublett Road corridor
• Mansfield Cardinal Road area

Service Area - Cities Near Kennedale

We coordinate dispatch and scheduling from our Dallas-Fort Worth office, and crews serve Kennedale locally along with surrounding communities. If you’re near the city line, we also work in Rendon, TX, Everman, TX, Forest Hill, TX, Arlington, TX, and Mansfield, TX. Every job carries the same written 90-Day Done Right Promise and upfront pricing, no matter which side of the county line you’re on.

FAQs About Gate Repair in Kennedale