Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Kenilworth
Gate parts and welding in Kenilworth come down to one thing most of the time: a hinge post that has shifted, a bottom rail rusted through, or a gate that suddenly scrapes the concrete where it cleared fine for decades. We fix those problems on site, in your driveway, without hauling the gate off to some shop. Hal Gatewood has been at this since 2001, and when you call (877) 610-2993, a live person answers. Not a menu. Not a chatbot.
Kenilworth is different from the towns around it. The lots are small, the driveways are tight, and most of the gates date back to the 1950s, 1960s, and 1970s. That matters when a post heaves or a hinge binds. We know these specific gates because we work on them all the time. If your gate is binding, sagging, or dragging, call us. We’ll tell you over the phone what we think is going on, then come look at it in person and give you a price before any work starts.
Why Gatewood Fence & Gate Is Kenilworth’s Preferred Gate Parts & Welding Company
We’re not a franchise and we don’t run a boiler-room call center. Hal Gatewood’s name is on the shop and on every invoice. The shop is down the road, not three states away. If you want to drive over and look Hal in the eye before you hire him, you can. That’s the oldest accountability there is.
Our Gate Parts & Welding crew has repaired and rebuilt gates all over Kenilworth, from the streets right off the Boulevard to the Parkway-adjacent blocks where old chain-link gates still stand as sound barriers. We answer the phone 24/7, and we show up when we say we will. Every job has the 90-Day Done Right Promise in writing. If something isn’t done right, one call brings Hal back. No runaround, no “that’s not covered.” If we touched it and it’s not right, we make it right.
Kenilworth homeowners tell us the same thing over and over: they already got burned once by a company that quoted one price on the phone and showed up with a different number at the door. We don’t do that. The price you agree to is the price you pay, in writing, before we start. And we back it with a promise stamped on the invoice, not buried in fine print.
Our Gate Parts & Welding Services in Kenilworth
Hinge Replacement
Hinges on 50-to-70-year-old Kenilworth chain-link gates fail two ways: the hinge pin wears thin and the gate starts to drop, or the hinge plate rusts through where it bolts to the post or frame. On tight Kenilworth driveways, a gate that drops half an inch starts dragging on the concrete apron immediately. We replace worn hinges with properly sized hardware, re-hang the gate to clear the apron, and adjust the latch and closer so the gate doesn’t fight itself.
Post Replacement
This is the big one in Kenilworth. Original post footings from the 1950s, 1960s, and 1970s were often poured shallow, and decades of Union County freeze-thaw cycles heave them out of plumb. In Kenilworth, a gate sags in the hinge post, not in the middle, and that is where we start. We dig out the old footing, pour a new one below frost line with proper depth, reset the post plumb, and re-hang the gate. Fix the panel without the post and you’ll fix it twice. We see that twice-a-year repair pattern all over the borough, and we’d rather fix it once.
Rail Repair
Bottom rails on Kenilworth’s older galvanized gates rust through at the roller bracket or hinge bracket, especially on Parkway-adjacent properties where the gate sat as a sound barrier with no maintenance for decades. When the bottom rail goes, the gate loses its structural straightness and starts to rack. We cut out the rusted section and weld in new galvanized rail, or replace the full rail when the corrosion has spread too far. The gate stays in your driveway the whole time. Our on-site welding means we don’t have to haul your gate off to a shop and leave the opening unsecured for a week.
Custom Welding
Some Kenilworth gates need more than a replacement part. When a custom bracket, a reinforced hinge plate, or a gate extension is needed to clear a tight apron or match a shared driveway offset, Hal welds it right there in the driveway. We’ve built up worn hinge barrels, added stiffeners inside sagging frames, and fabricated mounting plates for operators on gates that were never designed to take one. If it’s steel and it’s part of your gate, we can probably weld it.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Kenilworth
We’re certified to service nine major gate brands, including Linear, DoorKing, and Ghost Controls operators you’ll see on Kenilworth driveways and along the Boulevard. We keep common parts for these systems on the truck so a service call to Kenilworth doesn’t turn into two or three trips. If your opener is laboring, if a safety edge is cracked, or if the control board is doing something odd, call (877) 610-2993 and describe what you’re seeing. We’ll tell you what it likely is before we even roll out. And when we get there, the truck has the parts.
Common Gate Parts & Welding Problems We See in Kenilworth Homes
- Frost-heaved hinge posts. Union County’s findar freeze-thaw cycle, with sustained below-freezing temperatures from December through February, shoves shallow footings out of plumb. Come March, a gate that swung fine in November starts scraping the concrete apron. That’s the single most common call we get in Kenilworth, and it almost always means the post needs to be reset below frost line, not just shimmed.
- Rusted-through bottom rails. On Parkway-adjacent streets in the 07033 zip code, older gates were installed in the 1960s and 1970s as informal sound and privacy barriers, then largely ignored. The bottom rail rusts through at the roller or hinge bracket, the gate loses its shape, and suddenly the latch won’t line up. The rail needs welding or replacement, not just a hinge swap.
- Tight-clearance binding. Kenilworth’s post-WWII capes and ranches sit on unusually small lots. The original gates were built to swing or slide within inches of concrete aprons, shared driveways, and property lines. After minor sag correction, a gate that worked for 50 years can suddenly scrape. If the post wasn’t reset properly, the gate binds. We measure clearance before and after every job.
- Shallow original footings. Many Kenilworth gates from the 1950s through the 1970s were set in concrete maybe two feet deep, sometimes less. That’s not below the local frost line, and it guarantees the post will move. When we replace a post, we pour the new footing deep enough that the next March thaw doesn’t move it. That’s a detail a gate company from Westfield or Clark would never see, because they’re not looking at Kenilworth’s original footings every week.
Pricing for Gate Parts & Welding in Kenilworth, NJ
Here’s what Kenilworth homeowners should expect to pay. A hinge replacement on a single swing gate typically runs $180 to $320, including new hardware and re-hanging the gate to clear the apron. A bottom rail weld repair runs $220 to $410 depending on how much rail is corroded and whether we need to cut out a section or replace the full length. A full post replacement with a below-frost-line footing runs $425 to $780, including concrete, labor, and re-hanging the gate. Custom welding work is quoted per job after we see the gate, and the price is in writing before we start.
We don’t charge a trip fee inside the county. We also offer $40 off any repair over $200, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 for an exact quote. Estimates are free, and the number Hal gives you is the number on the invoice.
We Also Serve Cities Near Kenilworth
We work all over the Union County area around Kenilworth and beyond. We serve Cranford, Roselle Park, Union, and Westfield, and we’re familiar with the older gate stock in each of those towns. If you’re outside the borough, call (877) 610-2993 and ask if we cover your street. We probably do.
Serving Kenilworth, NJ - Our Local Coverage Area
We’re based in the Kenilworth area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Kenilworth
That’s frost heave. Union County’s findar freeze-thaw cycle pushes shallow gate post footings out of plumb over the winter, and by March the post has shifted enough that your gate drops and drags on the concrete apron. The fix is resetting the post below frost line and re-hanging the gate. Shim it and it will scrape again next spring. Call (877) 610-2993 and we’ll come look at it before it gets worse.
If the post is rusted through at the base, cracked, or moved so far out of plumb that the gate won’t clear the apron, the post is done. If it’s simply leaned a bit but the steel is sound, we can sometimes straighten and brace it. The real tell on Kenilworth’s older gates is whether the original footing is still holding. If the concrete around the post is cracked or sunk, the post needs a new footing, not just a brace. Hal will tell you straight which one you need, and the price is set before we start.
Yes, in most cases we can. We cut out the rusted section of the existing bottom rail and weld in a new galvanized rail section, then touch up the connection points. If the corrosion has spread into the frame corners where the rail meets the hinge side, the gate may be too far gone and replacement is smarter. We’ll show you what we’re seeing and quote both options. The gate stays in your driveway either way, and the price is in writing before we start.
Sometimes, and on small Kenilworth lots a slide gate can be the better answer because it doesn’t swing into a neighbor’s side yard or a shared driveway. But a slide gate needs a straight run along the fence line for the gate to travel, and on some of the borough’s tighter parcels there isn’t enough side clearance for the full gate width. We measure first, tell you if sliding is realistic on your specific lot, and if it is, we quote the full job including the track, rollers, and operator. Call (877) 610-2993 and we’ll come measure yours.
Look at the bottom rail first. On Parkway-adjacent Kenilworth properties, those gates were often installed as sound barriers and never maintained, so the bottom rail rusts through at the bracket and the gate racks. Check whether the gate has shifted on the hinge side and whether the latch still lines up without lifting the gate. If the post footing has heaved or the rail is rusted, call us. We inspect gates in the 07033 zip code all the time, and the inspection is free.
Call Gatewood Fence & Gate for Gate Parts & Welding in Kenilworth
If your gate is dragging, sagging, rusted, or just not swinging like it used to, call (877) 610-2993. Hal Gatewood or his crew will pick up, listen to what’s going on, and set a time to come to your Kenilworth home that works for you. The estimate is free, the price is in writing before any work starts, and every job carries the 90-Day Done Right Promise. We’ve been owner-operated since 2001, and Hal’s name is on the shop and on every invoice. That’s the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Kenilworth with professional gate repair and welding since 2001.