Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Kearny
Gate parts and welding in Kearny, NJ typically runs $180 to $950 depending on what failed: a hinge pin replacement starts around $180 while a full post re-set with a new dry-pack concrete collar and welded hinge set runs $400 to $700, and a custom welded repair on a rusted frame section lands between $250 and $650. Most Kearny jobs are done same-day or next-day because we carry hinges, rollers, latches, and weld stock in the truck. If your gate is sagging, rusting through a weld, or not latching, call (877) 610-2993 and you’ll get a straight answer from a live person, not a voicemail.
Kearny gates take a beating that gates in most of Hudson County never see. You’re in the tidal influence zone of the Passaic River and Hackensack Meadowlands, and the brackish air here eats steel hardware years faster than inland towns. We’ve been fixing gates in Kearny long enough to know which repairs actually hold and which ones just buy you a season.
Key takeaways:
- Kearny gate repairs typically cost $180 to $950, quoted and agreed before work starts
- Most hinge and latch problems on Kearny swing gates are actually post heave, not hinge wear
- Salt-air weld failure is the top call we get from the blocks closest to the Passaic
- We weld on site, so your gate never leaves the driveway
Why Gatewood Fence & Gate Is Kearny’s Preferred Gate Parts & Welding Company
Hal Gatewood has been running this shop since 2001, and the 90-Day Done Right Promise is stamped in writing on every job we finish in Kearny. If the repair doesn’t hold, one call brings us back, no runaround. Hal’s name is on the invoice, the shop address is published, and there’s a license number anyone can look up. That’s the oldest accountability there is: the name is on the shop, and the shop is down the road.
We answer the phone 24/7 with a live person, which matters when you’re standing next to a gate that won’t close and the neighbor’s dog is eyeing the opening. You won’t get a call center three states away. You’ll get us. Scheduling is coordinated from our New York City office, and crews serve Kearny locally, so the person who shows up knows the neighborhood and the soil.
We’re certified on nine major gate brands including Viking, Ghost Controls, DoorKing, and Elite, so when an operator board fails or a rack binds, we’re not guessing at it. And if you already have a written estimate from another company, bring it to us. We’ll give you a free second opinion, and if we’re doing a repair over $200, you’ll take $40 off. Veterans and seniors get 10% off, always.
Our Gate Parts & Welding Services in Kearny
Post Replacement
This is the repair we do more than any other in Kearny, and it usually starts with a homeowner convinced the hinges are the problem. On the streets near the Passaic, like the blocks around River Road and its side streets, gate posts are set in waterlogged Meadowlands fill that shifts every winter. A post that leaned six degrees will make every hinge adjustment you attempt worthless within a month. The fix that holds is cutting the old footing, re-setting the post in a dry-pack concrete collar, and welding on new stainless hinge plates. Post replacement in Kearny runs $400 to $700 per post, depending on whether we’re re-setting the existing post or setting a new galvanized one.
Hinge Replacement
On a Kearny swing gate, hinge pins are the first thing that salt air kills. Bare steel pins on a wrought iron gate set into a brick pier near the Hackensack Meadowlands can rust through in five to seven years. We replace them with stainless pins and stemmed hinges that thread into the post or weld onto the frame, so the next time you lift the gate off, you’re not watching a pile of rust fall out. Hinge replacement runs $180 to $400 per set, and we do it on site.
Rail Repair
Gates on the older brick row homes built between 1910 and 1950, the ones with narrow side yards along streets like Elm and Schuyler, often fail at the lower rail first. Rust collects where the rail meets the pickets, and one good freeze-thaw cycle after a nor’easter surge will snap it. We cut out the rotten section, fishplate or sleeve the rail, and weld it solid. Rail repair on a typical Kearny pedestrian gate runs $250 to $550.
Custom Welding
When a hinge post snaps clean off a gate frame, or a bracket tears away from a rusted rail, you don’t always need a new gate. You need a welder who can cut back to solid metal and rebuild the section. We do that in your driveway with a mobile rig, so your gate never leaves the property. Custom welding for a structural repair in Kearny runs $250 to $650, and the job gets quoted and agreed before the first arc strikes.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Kearny
We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Around Kearny we see a lot of Viking and Ghost Controls openers on the older residential swing gates, and DoorKing and Elite on the industrial sliding gates left over from the factory and warehouse era. We keep common hinge sets, rollers, and latch hardware stocked for Kearny jobs, and when a board or a limit switch fails we source the part from the manufacturer, not from a salvage pile. Salt air kills electronics too, so we check the board connections for corrosion on every service call, not just the metal.
Common Gate Parts & Welding Problems We See in Kearny Homes
- Post heave misdiagnosed as hinge failure. The fill under Kearny’s 1910s to 1940s brick row homes is soft, formerly marshy ground that heaves each winter. The gate sags because the post moved, not the hinge pin, and adjusting the hinge just chews up the threads.
- Rust-through at the hinge weld. Chloride-laden air from the Passaic and Meadowlands pits bare steel weld seams. We regularly see gates snap at the hinge post weld while the panel itself still looks fine.
- Flood-soaked posts and freeze-thaw frame twist. Streets lower down near the river flood during nor’easters. The water saturates the post footing, then freezes. The frame twists, the latch stops lining up, and the lock just won’t engage anymore.
- Operator boards dying on industrial slide gates. Legacy slide gates on redeveloped warehouse properties, especially around Kearny Point, still run undersized racks. When rust swells the rail, the rack binds and the operator cooks its own board trying to push through the resistance. The visible hardware looked fine right up until the board burned out.
Pricing for Gate Parts & Welding in Kearny, NJ
Here’s what you’re looking at in Kearny, in real numbers. Hinge replacement: $180 to $400 per set. Post re-set or replacement: $400 to $700 per post. Rail repair: $250 to $550. Custom welding repair: $250 to $650. Full gate frame repair with post re-set and welded hinge plates: $500 to $950. The price is quoted and agreed before any work starts, and there’s no trip charge inside the county. If you’ve already got a written estimate from another company, call (877) 610-2993 for a free second opinion. We’ll tell you honestly if their quote is fair, and then we’ll beat it if we can.
We Also Serve Cities Near Kearny
From our New York City office we dispatch crews into all of Hudson County’s river towns. Along with Kearny, our Gate Parts & Welding team handles calls in Harrison, Jersey City, North Arlington, and Belleville. Same crew, same truck, same 90-Day Done Right Promise.
Serving Kearny, NJ - Our Local Coverage Area
We’re based in the Kearny area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Kearny
Because your hinge post is moving in wet Meadowlands fill, and adjusting the hinges just re-torques the same loose footing. On the blocks near the Passaic, the soil is saturated and soft, and every freeze-thaw cycle shifts it a little more. The only fix that holds is re-setting the post in a dry-pack concrete collar and welding the hinge plates to the new set. Adjusting the hinges on a moving post is like tuning a guitar while the neck is bending. Call (877) 610-2993 and we’ll do the repair once, not every spring.
Galvanized steel with stainless fasteners and welded stainless hinge pins holds up. Bare steel and painted steel, even powder-coated, will rust through the weld seams in five to seven years once the coating gets a pinhole and chloride-laden air gets under it. For the hottest spots, right along the river, we recommend galvanized posts and stainless hardware everywhere the metal meets. It costs more up front, roughly 20 to 30 percent, but it outlasts painted steel two to three times. Call (877) 610-2993 and we’ll spec it properly for your block.
If the post is surface-rusted but the wall thickness is still there, we can grind back to clean steel and re-weld in place. If the rust has eaten through the wall or the post has shifted in softened fill, re-welding the surface won’t fix the footing. In Kearny, we usually see rust-through at the bottom six inches of the post, right where floodwater sits, and at the hinge weld. We’ll tell you which one you have after we look at it, and we’ll show you the rust, not just describe it. Estimates are free.
On Kearny’s industrial slide gates, yes, that’s common. When the rack rusts and swells, the gate binds, and the operator’s force sensor has to push harder until the board overheats and fails. The operator looks like the culprit, but the rust on the rail killed it. On residential swing gates, we see LiftMaster LA400s throwing force errors when the hinge post has shifted and the panel drags. Fix the post, then re-set the force limits. Call (877) 610-2993 and we’ll diagnose the actual failure before you spend money on a control board you might not need.
Yes. Under New Jersey requirements, any automated gate needs entrapment protection: photo eyes, edge sensors, or both depending on the gate and operator. If you’re having a gate welded or a post re-set and the opener is staying in service, we’ll verify the safety devices are working correctly while we’re on site. A welded repair that ignores the safety edges is not a repair worth having. We wire and test entrapment protection on every automated gate we service in Kearny.
Your Kearny Gate Repair Is One Call Away
If your gate is sagging toward the latch, rusting through a weld, or the opener is grinding and throwing errors, don’t wait until the post lets go entirely. Call (877) 610-2993 now. Hal or one of his crew will answer, and we’ll get to Kearny fast, quote the job at a fair price, and fix it so it stays fixed. 90-Day Done Right Promise, in writing, on every job.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate. Hal has been welding and repairing gates since 2001, and he stands behind every job with his personal 90-Day Done Right Promise.