Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Iona
Gate parts and welding in Iona comes down to one thing: your gate lives in salt air, sits on saturated ground, and takes wind from two directions. We replace hinge pins, reset posts, and weld frames on site so your gate swings true again without hauling it to some shop in another county. Hal Gatewood has run Gatewood Fence & Gate since 2001, and when you call (877) 610-2993, a live person picks up. If you live in Iona off McGregor Boulevard, in a canal-front community near San Carlos Bay, or back in a gated subdivision off Gladiolus Drive, we know what your hardware is fighting.
Key Takeaways
- On-site welding means your gate stays in your driveway, not on a flatbed headed to a shop.
- Iona’s salt air cuts hinge pin life to five to seven years where inland parts last a decade or more.
- Every job gets the 90-Day Done Right Promise in writing, plus a free estimate before work starts.
- $40 off any repair over $200, no trip charge inside Lee County, and a permanent 10% discount for seniors and veterans.
Why Gatewood Fence & Gate Is Iona’s Preferred Gate Parts & Welding Company
Iona is not like the rest of Lee County. The concentration of HOA-governed gated communities between the Caloosahatchee River and San Carlos Bay means nearly every gate here is motorized and monitored. A gate that fails is not a minor annoyance; it is a security gap for the whole community. Homeowners in Iona have called us after national outfits quoted one number on the phone and handed over a different invoice at the driveway. That does not happen with us. The price Hal quotes is the price you pay, agreed up front, in writing, before any torch is lit or any post is set.
We serve Iona from our South Florida office, with crews working locally across the 33906 zip code. Hal’s name is on the shop and on every invoice. The address is published. If something is not done right, the 90-Day Done Right Promise means one call brings him back. No runaround, no fine print about what “right” means. It means right.
Our Gate Parts & Welding team carries marine-grade hinges, galvanized posts, and rack sections sized for Lee County gate types. We do not order a generic part and hope it fits. We bring what Iona gates actually use.
Our Gate Parts & Welding Services in Iona
Hinge Replacement
Hinge replacement in Iona is the single most common repair call we get. Salt air works its way into the hinge pin bore and eats the metal from the inside out. The gate starts to sag, then the operator motor strains against the added load, and pretty soon the rack teeth strip or the control board overheats. We replace hinge leaves and pins with marine-grade stainless or hot-dip galvanized hardware, then re-align the gate so the operator is not fighting gravity. In Iona, a sagging gate is almost never just a hinge issue. It is a corrosion issue.
Post Replacement
Gate posts in Iona take a beating that inland posts never see. Saturated soil after a heavy rain or storm surge lets the post shift out of plumb. A post that moves a quarter inch at the footing translates to an inch or more of misalignment at the latch. We cut out old footings, set new galvanized posts with deeper embedment and anti-rot concrete, and weld reinforcement plates where the post meets the gate frame. If your swing gate binds mid-travel after a storm, the post is the first thing we check. Fix the panel without the post and you will fix it twice.
Rail Repair
Slide gates on Iona canal-front properties fail most often at the rail. Salt corrosion pits the top of the rail, the rollers chew into those pits, and the gate starts to shimmy and grind. We weld in new rail sections or build up eroded steel with controlled passes, then re-grease the rollers with a marine-rated lubricant that holds up to salt spray. On older Iona gates, the rail is often the original. It has done its job. The question is whether the rest of the frame has enough metal left to weld to. We tell you straight either way.
Custom Welding
Custom welding in Iona is not about doing something decorative. It is about making a gate that was never really designed for this environment hold up to it. We weld corner gussets, reinforcement plates, latch strike boxes, and bottom rails. On ornamental aluminum gates we use TIG where the metal is thin, MIG where it is structural. Hal welds on site whenever the job allows it, because hauling a gate away and hauling it back creates alignment problems of its own. Your gate stays in your driveway. You can watch the work.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Iona
Iona’s automated communities run on a handful of operator brands, and we service them all. Viking and DoorKing are the two we see most on the swing and slide gates along McGregor Boulevard and the canal-front streets. Linear operators show up regularly on mid-size estate gates. We keep common boards and limit-switch parts stocked for these brands so a repair in Iona does not wait on a slow freight truck. Hal’s crew is certified to service nine major gate brands, and we do not send you to a distributor for parts. We carry them.
Common Gate Parts & Welding Problems We See in Iona Homes
- Sagging swing gates from salt-eaten hinge pins. The pin wears inside the leaf, the gate drops, and the operator motor burns out trying to lift it back. In Iona, this happens in five to seven years, not the ten-plus you would get inland.
- Hinge posts shifting in saturated ground after storms. Iona’s water table sits close to the surface. When the ground saturates, footings lose grip. The gate binds mid-travel, tears the latch, or bends the post itself.
- Underground loop detectors and safety photocell wiring shorting out. Standing water after seasonal storm surge or heavy rains gets into conduit and junction boxes, knocking the gate out of auto mode. The gate still works manually, but the operator will not hold a cycle.
- Rack and pinion stripping on slide gates from salt corrosion. The rack teeth wear faster when salt pits the steel. The gate slips, shudders, and finally stalls. Replacing the rack before the pinion strips saves you an operator replacement.
Pricing for Gate Parts & Welding in Iona, FL
You deserve real numbers. In Iona, hinge replacement on a standard swing gate typically runs $180 to $340 per hinge assembly, including marine-grade hardware and re-alignment. Post replacement, including cutting out the old footing and setting a new galvanized post, runs $450 to $900 depending on embedment depth and soil condition. Slide gate rail repair runs $300 to $650 per section welded. Custom welding for reinforcement plates or frame repair runs $150 to $400 per hour of torch time, with most Iona jobs falling in the two-to-three-hour range. Every quote is written down and agreed before work starts. Free estimate. No trip charge inside Lee County. Call (877) 610-2993 and Hal will tell you what he would do and what it costs.
We Also Serve Cities Near Iona
If you live near Iona, we work in your neighborhood too. Our Gate Parts & Welding in Iona crews run calls every week to Cypress Lake, McGregor, Fort Myers Beach, and Villas. Same local knowledge, same written promise. If your gate is in Lee County, it is in our service area.
Serving Iona, FL - Our Local Coverage Area
We’re based in the Iona area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Iona
Because lubrication does not replace metal that salt air has already eaten away. The hinge pin wears inside the leaf bore, and no amount of grease will bring back the diameter the pin needs. The fix is replacing the hinge pin and leaf with a marine-grade set, not re-lubricating a worn assembly. Call (877) 610-2993 and we will inspect the hinge wear on site and tell you if replacement is actually needed.
Yes, in most cases. If the surrounding steel has enough remaining wall thickness to accept a weld, we can grind back the corrosion, weld in fresh reinforcement plate or tube, and coat it for salt-air exposure. The panel stays in place. If the frame is rusted through in load-bearing sections, we will tell you honestly before we light a torch. Call (877) 610-2993 for a free assessment.
First, manually release the operator. There is a release handle or key on the side of the operator housing. Pull it and the gate will swing or slide by hand. Then padlock or chain the gate closed so it does not become a wind sail in sustained gusts. Then call (877) 610-2993. We run storm-response calls through Iona and we will get the gate locked down properly and the operator re-engaged when power returns.
Listen for a grinding or clicking sound as the gate travels. Look at the rack teeth. If they are pointed, pitted, or worn to a knife edge on the top surface, salt has done its work. The pinion gear will follow soon. Replacing the rack before the pinion strips saves you an operator. Call (877) 610-2993 and we will put a straight answer on it.
Not usually. If the post itself is still plumb and the steel is sound, we can cut off the corroded hinge leaf, grind the post clean, and weld on a new marine-grade leaf. If the post is leaning or the interior is rotted from trapped moisture, then post replacement is the honest fix. We will show you what we see before any work begins. Call (877) 610-2993.
Call Gatewood Fence & Gate for Gate Parts & Welding in Iona
If your gate is sagging, binding, or simply not opening like it should, call (877) 610-2993. Hal Gatewood has been at this since 2001. The name is on the shop, the address is published, and a live person answers the phone. You get a free estimate, a written price, and a 90-day promise on the work. Not a call center, not a dispatch queue. Just a guy who cares about doing the job right.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Iona since 2001.