Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Hyattsville
Gate parts and welding in Hyattsville usually means one of two scenarios. Either your rear-alley gate has sagged past the point where a hinge swap will hold it, or your HOA-managed townhome community needs a shared entry gate repaired without a three-week wait. A hinge replacement with post correction on a 1940s Hyattsville rowhouse typically runs $380-$780, and a full post re-pour with welding starts around $650. We answer the phone at (877) 610-2993, and the person who answers can tell you honestly whether you need a part or a post.
Hyattsville‘s older blocks don’t play by the same rules as newer subdivisions. The alley gates back there were built into clay-heavy Prince George’s County soil, and most have been quietly heaving out of square for sixty or seventy years. We know that before we even roll into your alley off Queens Chapel Road or down by the 20784 side of town. That local knowledge changes what we quote, what we fix, and how long it lasts.
Why Gatewood Fence & Gate Is Hyattsville’s Preferred Gate Parts & Welding Company
Hal Gatewood’s name is on the shop, and the shop answers the phone around the clock. No dispatch queue, no voicemail wall. When you call the number, a person picks up. That matters in Hyattsville, where homeowners have learned to check whether a company has an actual address before they schedule anything. We do, and we’ve been owner-operated since 2001.
Hyattsville customers call us for one reason more than any other: a gate that someone else “fixed” is sagging again eight months later. The old fix replaced hinges and left the post leaning. We don’t do that. Show us the gate closing on its own and we’ll show you where it’s failing, usually at the footing. That’s the kind of answer that has built our local reputation along Baltimore Avenue and throughout the 20785 and 20787 zip codes.
Every gate repair in Hyattsville carries our 90-Day Done Right Promise, in writing. If it’s not done right, one call brings us back. No runaround. We also offer a free second opinion on any written estimate you’ve received, and no trip charge inside the county. Seniors and veterans get a permanent 10% discount, always.
Scheduling and coordination run from our Washington, DC office, with crews serving Hyattsville locally. Call (877) 610-2993 and we’ll tell you when we can be there.
Our Gate Parts & Welding Services in Hyattsville
Most of what we do in Hyattsville falls into four buckets. Here’s how each one looks in this city specifically.
Hinge Replacement
Hinge replacement in Hyattsville is rarely just a hinge replacement. On the 1930s-1950s rowhouses behind Baltimore Avenue, the hinge barrels wear and the gate drops, but the deeper problem is usually that the post has rotated with the frost. We replace hinges with heavier welded barrels where the gate style calls for it, and we check post plumb before we ever quote the part. A gate sags in the hinge post, not in the middle, and that is where we start. Typical hinge replacement with minor post correction runs $380-$780 in Hyattsville.
Post Replacement
This is the job Hyattsville’s old alley gates actually need most. The original posts were set directly into the county’s expansive clay with no gravel base. Decades of freeze-thaw cycles have cracked the concrete and tilted the post, so the whole gate leans and the latch misses. We cut out the old post, pour a new footing with a gravel bed and rebar cage, set the replacement post, and weld the hinges on true. In Hyattsville’s soil this is the only fix that holds. Post replacement with welding typically runs $650-$1,100 depending on gate size and access.
Rail Repair
Top and bottom rails on older tubular steel gates in Hyattsville corrode from the inside. Summer humidity strips the paint, and condensation does the rest. We repair or splice rails on site, so your gate stays in your driveway rather than getting hauled off somewhere. Rail repair with welding runs $180-$420 in most Hyattsville cases, and we’ll quote it before we touch anything.
Custom Welding
Sometimes the right part doesn’t exist anymore. A 1940s wrought iron alley gate off 42nd Avenue might need a matching picket fabricated, or a Cape Cod owner might want a custom steel frame built to match the original rowhouse style. We weld on site and fabricate to match. Custom welding jobs in Hyattsville start around $250 for simple frame repairs and run up from there based on the work. If you can describe it or show us a photo, we’ll give you a written price.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Hyattsville
For Hyattsville townhome communities and homeowners with gate motor & opener systems, we service DoorKing, Elite, and Viking operators regularly. Parts for these brands are what we order most, so we keep common components close and know the failure points. If your shared entry gate runs one of these operators and it’s misaligned after post work, that’s a repair we can usually schedule the same week. Whether it’s a Viking loop detector or a DoorKing control board, we’ll tell you the part, the price, and when it’s done before we start.
This page covers Gate Parts & Welding broadly. Everything above applies specifically to how we work in Hyattsville.
Common Gate Parts & Welding Problems We See in Hyattsville Homes
- Tilted posts from expansive clay. Older rear-alley gates in Hyattsville were set without drainage gravel. Every winter the clay heaves, the footing cracks, and the post leans a little more. By the time the latch won’t catch, the post is usually several degrees off plumb.
- Hinge failures that follow post movement. When the post tilts, the hinge takes the load unevenly and the barrel wears out fast. Swapping the hinge without fixing the post gets you about one more season before the sag returns.
- HOA approval mismatches near Prince George’s Plaza Metro. Townhome communities with shared entry systems have architectural review boards. A gate part changed to a different finish or height without approval gets flagged at the next walkthrough, and then the repair has to be redone.
- Rust through on bare steel frames. Hyattsville’s humid summers strip paint from unmaintained steel gates. Once the coating fails, the metal rusts from the outside in, and rail sections need to be cut out and welded new. This is the repair we see most on original rowhouse gates.
Pricing for Gate Parts & Welding in Hyattsville, MD
- Hinge replacement with post correction: $380-$780
- Full post replacement with new footing and welding: $650-$1,100
- Rail repair or splice welding: $180-$420
- Custom welding (frame repair or fabrication): $250 and up, quoted before work starts
- Shared entry system repair (loop detector, photocell, operator board): $220-$540 depending on the part
These are honest Hyattsville market ranges, not teaser numbers. Your price is written down and agreed to before any work starts. We don’t change it at the door. Free second opinion on any written estimate, and $40 off any repair over $200. Call (877) 610-2993 for an exact quote.
We Also Serve Cities Near Hyattsville
Beyond Gate Parts & Welding in Hyattsville, we regularly work in Riverdale Park, East Riverdale, Bladensburg, and Cheverly. Same owner, same 90-Day Done Right Promise, same live person answering the phone. If you’re a few blocks over the line, you’re still close enough for us to take care of you.
Serving Hyattsville, MD - Our Local Coverage Area
We’re based in the Hyattsville area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Hyattsville
Yes, in most Hyattsville rowhouse blocks and townhome communities, you do. Even if the post is original and failing, the HOA’s architectural committee typically wants to see the replacement post type, finish, and height before work starts. We help by providing the specification sheet and a written description of the scope. Call us at (877) 610-2993 and we’ll tell you what your board is likely to ask for.
Because the post is moving. In Hyattsville’s older rowhouse blocks, the original post was set in concrete poured directly into Prince George’s County clay with no gravel bed. Frost heave tilts the post every winter. If the hinge was replaced but the post was not corrected, the new hinge starts wearing against the now-crooked frame immediately. The fix is post correction or replacement, not another hinge swap. Call (877) 610-2993 and we’ll come check the plumb.
Yes. We fabricate and weld on site, matching original picket spacing, frame dimensions, and finish where the gate needs to blend with the rest of the block. This comes up often in Hyattsville’s older sections near Baltimore Avenue and along the 20787 zip code, where a mismatched modern panel looks wrong next to 1940s ironwork. Send us a photo and we’ll give you a written price.
Directly, by phone and email. We handle the part approval, the scheduling window, and the walkthrough on the back end. For shared entry systems in Hyattsville’s gated townhome communities near Prince George’s Plaza Metro, misaligned loop detectors and photocells after post work are the most common failure we correct. We’ll send the management company a written scope before any work starts. Call (877) 610-2993 and we’ll coordinate it.
Almost always at the post. The gate panel is a rigid frame; it doesn’t bend by itself. The post it hangs from tilts or settles, and that’s what drags the latch plate out of alignment. In Hyattsville’s rowhouse alleys, the post has usually been heaving in clay for decades before anyone notices. Fix the panel without the post and you’ll fix it twice. Call (877) 610-2993 for a free estimate and we’ll tell you which one you actually have.
Call Gatewood Fence & Gate for Gate Parts & Welding in Hyattsville
Whether it’s a 1940s alley gate with a tilted post, a shared entry system down by the Metro corridor, or a custom weld to match the original ironwork, we’ll give you a straight answer and a written price before anything starts. The name is on the shop, and the shop is down the road. Call (877) 610-2993 for a free estimate. Hal answers.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Hyattsville since the company’s founding.