Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Hornsby Bend
Gate posts in Hornsby Bend lean because the river-bottom clay moves, and a gate that won’t latch is a gate that won’t keep anything in or out. Gatewood Fence & Gate has been handling Gate Installation - Hornsby Bend and repairing gates across the 78725 ZIP since long before the new subdivisions started rising along FM 969. When your hinge post has heaved out of plumb or a storm has racked your swing gate, Hal Gatewood and his crew show up in a truck with a welder, not a clipboard and a replacement-part catalog. Call (877) 610-2993 and a live person answers, day or night. We quote the price before we strike an arc, and the 90-Day Done Right Promise is on every invoice.
Why Gatewood Fence & Gate Is Hornsby Bend’s Preferred Gate Parts & Welding Company
Hornsby Bend isn’t a stop on a route for us. The name on the shop is Hal Gatewood, and the shop is down the road. Since 2001, we’ve been the company that comes out when a post has heaved, a rail has snapped, or a gate has sagged so far it drags a trench in the driveway. Our Gate Parts & Welding team knows what the clay east of the treatment plant does to shallow footings because we’ve dug enough of them out by hand to know better. When someone in Hornsby Bend calls about a gate that won’t close after a squall, we don’t send a salesperson. We send somebody who can weld on site, in your driveway, and be gone before the next band of weather rolls through.
In Hornsby Bend, our customers are ranchers, long-time 78725 families, and folks in the newer homes along the Colorado River bottomlands. They’ve all got the same complaint: the ground moves, and the gate follows it. We’ve reset posts off FM 969, straightened racked panels near the treatment plant, and rebuilt more hinge points than we can count. Customers around here don’t ask for a quote and wait. They ask when we can come. The answer, for anything in Hornsby Bend, is usually same day or next morning. And every job carries the same promise: if it’s not done right, one call brings us back. No runaround, no fine print.
Our Gate Parts & Welding Services in Hornsby Bend
Hinge Replacement in Hornsby Bend
A gate sags in the hinge post, not in the middle, and that’s where we start. The expansive clay under Hornsby Bend doesn’t just shift posts; it torques hinge barrels until they bind, squeal, and eventually snap. We replace worn or broken hinges on pipe-panel ranch gates, ornamental iron driveway gates, and livestock gates, and we weld the new hinge in place rather than bolting a mismatched hardware-store part onto steel that’s already fatigued. Fix the hinge without checking the post, and you’ll fix it twice. We check both.
Post Replacement in Hornsby Bend
This is the repair we do most in the 78725 ZIP, and it’s not close. Hornsby Bend sits on dense, dark shrink-swell clay that grips a shallow-set post in the dry months, then lets go when the ground gets saturated. The post heaves, tilts, and drags the gate out of alignment. A shallow-set post east of the treatment plant will be out of plumb by a full inch or more within two to three wet-dry cycles. We don’t just re-set the post in the same hole. We core a concrete pier below the active clay layer, set the post on that, and weld the gate back into a proper rack and pinion alignment. That’s the only fix that lasts in Hornsby Bend.
Rail Repair in Hornsby Bend
Wind load on solid infill gate panels is a real force out here. When a storm pushes a fifty-mile-an-hour gust against a closed gate, the panel acts like a sail, and the weakest point is usually the rail. We see broken top rails, cracked mid rails, and weld joints that have popped clean apart on newer ornamental gates in Hornsby Bend. We grind out the old weld, re-align the rail, and weld it properly. On aluminum driveway gates, that means the right filler rod and heat control, not a quick tack that cracks again in a month.
Custom Welding in Hornsby Bend
Sometimes the part you need doesn’t exist in a catalog. An old pipe-panel gate from the 1970s, a livestock chute that’s been patched three times, a driveway gate that needs a section rebuilt after a truck clipped it. We weld on site, in your driveway or pasture, so the gate never has to leave Hornsby Bend. Hal has been welding since 2001, and he’d rather repair a gate than replace it. Bring us a gate that’s broken in a way you can’t explain, and we’ll figure it out.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Hornsby Bend
We stock parts and service our Gate Motor & Opener in Hornsby Bend equipment for the brands you’ll actually find on gates in Hornsby Bend: FAAC, BFT, Linear, and Viking among them. Older ranches around 78725 tend to run simple swing operators, while newer automated driveway gates use whatever the installer sold. We service all of it. If we don’t have the part on the truck, we get it fast, and we don’t charge a trip fee inside the county. A live person answers when you call to ask about a part. That person can usually tell you if we’ve got it before you hang up.
Common Gate Parts & Welding Problems We See in Hornsby Bend Homes
- Heaved hinge posts from clay shrink-swell: The river-bottom clay in 78725 expands and contracts so aggressively that hinge posts lean a full inch or more within a few seasons. The fix is a deep pier below the active clay, not another bag of quick-set concrete in the same shallow hole.
- Sag correction failures that return within a season: When a post is reset shallow and the gate sags again by fall, the problem was never the hinge or the rail. It was the footing. We replace the post on a proper pier and the sag stops coming back.
- Silt in automatic gate operators after floods: Low-lying sections of Hornsby Bend near the Colorado River floodplain can take on water. Silt gets into the rack and pinion, jams the slide gate, and trips the loop detector until somebody cleans and re-lubricates the mechanism.
- Wind-racked panels on solid infill gates: A solid gate panel in a straight-line wind is a sail. The load wracks the hinge post out of plumb and cracks rail welds. We realign the post, re-weld the rails, and check the gate’s swing clearance so it opens freely even when the ground is soft.
Pricing for Gate Parts & Welding in Hornsby Bend, TX
Here’s what you can expect in Hornsby Bend. A hinge replacement on a standard swing gate typically runs $180 to $340, including the new hinges and the welding. A post replacement that requires a deep concrete pier below the active clay layer usually lands between $450 and $900, depending on whether it’s a light wood post or a heavy steel gate post. Rail repair runs $150 to $400, depending on the length of the crack and the access. A custom welding job that takes an hour or two on site is typically $150 to $350. Every price is quoted and agreed before any work starts. You’ll get $40 off any repair over $200, and seniors and veterans always get 10% off. Estimates are free, and the 90-Day Done Right Promise stands behind all of it.
We Also Serve Cities Near Hornsby Bend
Our crews work up and down the east side of Travis County every week, so if you’re in Hornsby Bend, you’re already on our route. We also handle gate parts and welding in Austin, Manor, Pflugerville, and Wells Branch. Same crew, same promise, same phone number.
Serving Hornsby Bend, TX - Our Local Coverage Area
We’re based in the Hornsby Bend area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Hornsby Bend
Hornsby Bend sits on deep, expansive clay in the Colorado River bottomlands, while Austin’s western hills sit mostly on limestone. Clay expands when it’s wet and shrinks when it’s dry, and that cycle pushes shallow-set posts out of plumb in just a few seasons. Limestone doesn’t move. That’s why a post set shallow in 78725 will lean a full inch within two or three wet-dry cycles, while the same post out west might stand straight for a decade. The fix is the same in both places: set the post on a deep pier below the active soil. Call (877) 610-2993 and we’ll come take a look for free.
The sag is almost always the post. A gate sags in the hinge post, not in the middle. The storm saturated the clay around your post, the clay lost lateral support, and the post leaned. You can weld a brace on the panel and it will sag again within a season because the post is still moving. Have the post checked first. If it’s leaning, we reset it on a deep concrete pier and then re-hang the gate. Fix the post and the panel problem goes away. Call (877) 610-2993 for an exact quote. Estimates are free.
Most automatic gate operators in Hornsby Bend have a manual release mechanism. On slide gates, it’s usually a keyed release or a handle on the operator that disengages the motor from the chain so you can push the gate by hand. On swing gates, the release disengages the arm from the gate leaf so it swings freely. Never try to force a gate past the motor while it’s engaged. That’s how you strip a gear or bend a rack. If you can’t find the release or the gate won’t move after it’s disengaged, call (877) 610-2993. We’ll talk you through it or come out and take care of it.
Check the safety photocells first. They’re the small sensors on either side of the gate opening, usually waist height. When the gate is in motion, block the beam with your hand and the gate should stop and reverse. If it doesn’t, the sensor is misaligned, buried in silt, or disconnected. After a flood, silt and debris can knock the beam out of alignment or cake onto the lens. Also check that the gate reverses when it meets resistance, like a cinder block set in its path. If either safety feature fails, have it repaired or look into Gate Access Control in Hornsby Bend before kids or animals are around that gate. We can test and repair it. Call (877) 610-2993.
Yes, we weld aluminum rails on driveway gates all the time in Hornsby Bend. The key is the right filler rod, the right heat, and a clean, beveled joint. A cracked rail on an ornamental aluminum gate can’t just be tacked. It has to be ground out, re-aligned, and welded properly, or it cracks again right next to the first repair. We do it on site in your driveway. You’ll get a straight answer on price before we start, and the 90-Day Done Right Promise covers the weld. Call (877) 610-2993 for a quote.
Call Gatewood Fence & Gate for Gate Parts & Welding in Hornsby Bend
When a gate drops in Hornsby Bend, you need somebody who knows the clay, the wind, and the difference between a repair that lasts and a patch that buys you a season. Gatewood Fence & Gate has been handling Gate Parts & Welding in this ZIP since 2001. We answer the phone with a live person around the clock, quote every price before the work starts, and put the 90-Day Done Right Promise in writing. Hal Gatewood put his name on the shop, and he’ll put it on your invoice too. Call (877) 610-2993 for a free estimate. We’ll be there.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Hornsby Bend since 2001.