Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Hillsboro
Gate parts and welding in Hillsboro usually means one of three things: a hinge that rusted through after years of Tualatin Valley rain, a post that heaved out of plumb in the clay, or an operator that quit because the gate frame was binding against it. We fix all three. Hal Gatewood has been at this since 2001, and our Gate Parts & Welding crew shows up with a welder on the truck, parts that actually fit your gate, and a 90-Day Done Right Promise in writing. If your gate is dragging, sagging, or swinging wild in Hillsboro, call (877) 610-2993 and you’ll get a live person, not a voicemail.
Why Gatewood Fence & Gate Is Hillsboro’s Preferred Gate Parts & Welding Company
Hillsboro is not a place where you can fake local knowledge. The gate at an Orenco Station HOA off NW 231st Avenue has different problems than a wood privacy gate near downtown. We know the difference because we drive these streets every week.
Hal’s name is on the shop and on every invoice. The crew wears uniforms, passes background checks, and works on gates in Hillsboro neighborhoods from Jackson School Road down to the 97123 corridor and up through the 97124 planned communities near Intel. We have been serving this part of Washington County long enough that neighbors tell neighbors to call us, which matters more than any ad.
We answer the phone 24 hours a day. You won’t reach a call center three states away. You’ll reach a person who can tell you whether a binding gate is a hinge problem or a post problem before we ever set foot on your driveway. And we quote the price before any work starts, so the number we agree on is the number on your invoice.
Our Gate Parts & Welding Services in Hillsboro
Hinge Replacement
Hillsboro gets 37-plus inches of rain a year, most of it between October and May. That moisture finds its way into hinge barrels and rusts them from the inside out. We replace rusted-through hinges with sealed or stainless hardware that holds up better in wet clay soil conditions, and we true the gate panel so it doesn’t hang heavy on the new hinge and chew it up again.
Post Replacement
The clay-heavy soil under north Hillsboro’s Intel-era subdivisions saturates and shifts each wet season. Gate posts heave, the frame racks, and the gate drags. We dig out the old post, re-plumb it with a deep concrete footing that reaches below the frost line and into stable soil, and set it true. This is the fix that actually lasts. A new motor on a racked post is a waste of money.
Rail Repair
Ornamental iron rails on Hillsboro HOA gates take a beating from rain and ice. When a rail cracks or snaps at the weld, we cut out the damaged section and weld in new material on site. The gate stays in your driveway the whole time. No hauling it off, no waiting weeks for a shop to get around to it.
Custom Welding
Sometimes the part you need doesn’t exist anymore because the gate is 25 years old and the manufacturer moved on. We fabricate what’s missing, whether that’s a custom hinge plate, a latch box rebuild, or a section of ornamental iron matched to the existing pattern. The weld gets ground smooth, primed, and painted to blend with what was there before.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Hillsboro
We’re certified to work on nine major gate brands, including Linear, Viking, Ghost Controls, and DoorKing systems that are common in Hillsboro’s HOA communities. When an older operator needs parts, we know which ones are still available and which ones are better replaced with good aftermarket equivalents. Because we service Hillsboro regularly, we stock the hinge pins, rack sections, and latch parts that these systems actually wear out, which means fewer trips and faster fixes for you.
Common Gate Parts & Welding Problems We See in Hillsboro Homes
- Rusted hinges on ornamental iron gates. The 1990s and 2000s HOA boom near Intel put up thousands of iron gates, many with raw steel hinges that were never meant for 37 inches of annual rain. They rust through in 8 to 10 years, and the gate starts sagging. The panel looks fine; the hinge is shot.
- Clay-soil post heaving and frame racking. North Hillsboro clay swells when saturated and shrinks when dry. Posts move, gates bind, and the motor strains against the frame until something breaks. The fix is re-setting the post, not just replacing the motor.
- Ice-storm hinge seizure. Freezing rain, not snow, is Hillsboro’s winter gate killer. Ice gets into hinge barrels overnight and seizes the joint. Then the opener torques the hinge off the post. We see it every time there’s a bad ice event.
- Worn rack and pinion on slide gates. On automated slide gates, the rack teeth wear down over 20-plus years until the motor spins and the gate doesn’t move. We weld in new rack sections and re-align the drive so the operator isn’t fighting a dragging gate.
Pricing for Gate Parts & Welding in Hillsboro, OR
Here’s what we typically see in the Hillsboro market. A basic hinge replacement runs between $180 and $340, depending on whether we have to fabricate brackets. A post replacement with a deep concrete footing runs $650 to $1,200 in Hillsboro’s clay soil, since the footing has to be dug deeper than in Portland’s better-drained east side. Rail repair welds usually run $150 to $400, and custom fabrication starts around $250 and moves up from there. These are the ranges we quote before work starts.
We offer $40 off any repair over $200, no trip charge inside the county, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 and we’ll get you an exact number before anyone makes a cut.
We Also Serve Cities Near Hillsboro
Beyond Hillsboro itself, our crews handle gate parts and welding work in Hillsboro neighboring communities including Cornelius, Aloha, Rockcreek, and Bethany. If you’re in one of those areas or anywhere else in Washington County, the same pricing, the same promise, and the same live-person phone answer apply.
Serving Hillsboro, OR - Our Local Coverage Area
We’re based in the Hillsboro area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Hillsboro
If your gate is in an HOA-governed community in the 97124 corridor, check your CC&Rs before we make changes to the visible hardware or finish. Most Hillsboro HOAs require approval for any change to gate style, height, finish, or material, including hinge replacement if it changes the look. Our team has worked with many Hillsboro management companies and can provide a scope-of-work description and material specs for your committee. Call (877) 610-2993 and we’ll help you put together the paperwork.
The most common cause in Hillsboro is a racked or heaved gate binding the motor. When a post settles or heaves in the clay, the frame twists and the gate drags. The motor works against that resistance until it burns out. Replacing the operator without re-plumbing the post will just burn out the next one. We check the post, hinges, and rack alignment first.
Yes, we can weld a broken rail and protect the surrounding finish. The weld area will need touch-up paint after the repair because welding heat will burn the powder coat at the seam, but we grind the weld flush, prime it, and color-match the existing finish so the repair doesn’t stand out. Most HOA committees accept this when the color match is done right. We can quote it before starting.
Usually it’s a parts issue with the loop detector itself, the loop wiring, or the connections at the operator board. In Hillsboro’s wet soil, underground loop wires can absorb moisture and drift out of calibration, which makes the gate act like it doesn’t know a car is waiting. We can test the loop, replace the detector, or run a new loop where needed. Call (877) 610-2993 and we’ll diagnose it on site.
Most post replacements on Hillsboro HOA gates take one full day, sometimes two if the soil is saturated and the old footing needs extra excavation. For gates that must stay operational during Intel shift changes, we can schedule the work during lower-traffic hours and provide a temporary support so the gate stays functional while the new concrete cures. Tell us your traffic pattern and we’ll build the schedule around it.
Key Takeaways: Gate parts and welding in Hillsboro is shaped by clay soil, heavy rain, and 20-to-30-year-old HOA gate hardware. Hinge replacement typically runs $180-$340, post replacement $650-$1,200, and rail welding $150-$400. We fix gates on site, answer the phone with a live person 24/7, and put the 90-Day Done Right Promise in writing on every job.
If your Hillsboro gate is sagging, dragging, or just not latching right, call Gatewood Fence & Gate at (877) 610-2993. Hal will quote the price before any work starts, and if it’s not done right, one call brings him back. That’s the promise, and it’s in writing.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Hillsboro and Washington County.