Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Hartsdale
If your Hartsdale gate sags, binds, or won’t close square after a bad winter, you’re dealing with one of two things: a hinge that’s given up or a post that’s moved. The fix almost always starts under the ground, not at the latch. Gatewood Fence & Gate handles gate parts and welding across Hartsdale with on-site repair work, so the gate stays in your driveway while we fix it. Call (877) 610-2993 and you’ll get Hal Gatewood or his crew, not a phone tree. We start with a straight answer about what’s actually wrong and what it’ll cost, in writing, before any work begins.
Why Gatewood Fence & Gate Is Hartsdale’s Preferred Gate Parts & Welding Company
Hal Gatewood has been doing this since 2001. The company’s name is on the shop, the license number is published, and the phone rings to a live person around the clock. That matters in Hartsdale, where most gate work is on mid-century homes with original ironwork, and the homeowners have usually had at least one bad experience with a crew that was hard to reach after the invoice cleared. We’re the opposite of that. Our Gate Parts & Welding team shows up when we say we will, with the truck stocked so we’re not running back and forth to a supplier.
Hartsdale customers call us because they want somebody who will look at the post before ordering hinges. On the hillier streets west of Central Avenue, near Ridge Road Park and up toward the Hartsdale train station, we see the same pattern repeatedly: a gate that looks like a simple hinge job is actually a footing problem. A level check takes two minutes and saves a repair that fails next January. That’s the work we do, and we do it in your driveway with welding gear on the truck. Every job carries our 90-Day Done Right Promise in writing. If it’s not right, Hal comes back. No runaround.
Our Gate Parts & Welding Services in Hartsdale
Hinge Replacement
Most ornamental gates in Hartsdale hang on pintle hinges set into brick or fieldstone pillars, and most of them were installed 50 to 90 years ago. We see hinge pins corroded to the point where the gate has dropped half an inch and scrapes the driveway. We replace the hinge, but we also check the anchor plate in the pillar. If the mortar around the plate has spalled and the plate is moving, welding a new hinge onto a loose plate is wasted effort. We do it right, which sometimes means chipping out the old anchor, setting a new plate in epoxy or fresh mortar, and welding the hinge to the gate and post straight. Typical hinge replacement in Hartsdale runs $280-$650 per hinge set, depending on the weight of the gate and whether the post anchor needs rebuilding.
Post Replacement
In Hartsdale, the post is usually the problem. Greenburgh’s building department requires gate post footings below the 42-inch frost line, but plenty of original 1930s to 1960s installations sit at 24 inches or less. Our clay-heavy glacial soils heave every freeze-thaw cycle, and the post leans a little more each year. We dig out the old footing, pour a new one at 48 inches where we can, set the post, and re-weld the gate. Post replacement in Hartsdale typically lands between $900 and $2,400 depending on soil, post size, and whether we’re working around ledge rock. That’s the honest range for this town’s terrain.
Rail Repair
A gate sags in the hinge post, not in the middle, and we start there before we touch a rail. But rails do break, especially on heavy ornamental ironwork that’s been ice-loaded a few too many times. We cut out the failed section, weld in new matching stock, and paint it to blend. On older Hartsdale gates with custom scrollwork, we match the profile rather than bolting on a generic replacement. Rail repair runs $350-$800 for a typical mid-rail fracture, more if the gate has multiple broken pickets or the scrollwork needs replication.
Custom Welding
Some gates in Hartsdale aren’t worth scrapping just because a hinge boss cracked or a decorative finial snapped off. Hal’s welding is done on-site, with the gate still hanging or laid out on sawhorses in your driveway. We weld cast iron and wrought iron, fabricate replacement sections, and re-drill for modern operators when a retrofitted panel doesn’t quite line up. If a part is only made for a gate they stopped producing in 1971, we make it. Custom welding jobs start around $250 for small repairs and go up from there, and the price is agreed before we strike an arc.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Hartsdale
Certified to service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Around Hartsdale, the retrofitted operators on 1960s swing gates are often older FAAC or BFT units, and a fair number of the slide gates running on commercial properties use Viking or Linear boards. We stock common control boards, safety edges, and photocells for these brands locally, so residential service calls don’t stretch out waiting on a courier. If your operator lost its brain after a power flicker, we can usually get you running the same day. The weld work doesn’t have to wait for the electronics and vice versa.
Common Gate Parts & Welding Problems We See in Hartsdale Homes
- Frost heave on pillar-mounted gates. Footings installed before Greenburgh enforced the 42-inch frost line sit at 24 inches or less. Every winter, the ground lifts, the post tilts, and the hinge binds. The repair is a footing, not a hinge adjustment.
- Ice-storm weld failures. Hartsdale’s ornamental ironwork is heavy. When a February ice storm loads an extra few hundred pounds on dense scrollwork, the welds at the hinge post or mid-rail snap. We see it every late winter on the hillier, wooded lots.
- Corroded hinge pins in brick pillars. Moisture gets behind the anchor plate, the mortar spalls, and the pin rusts inside the barrel. The gate drops and scrapes. Pulling the pin and replacing just that part fixes it if the post is still sound.
- Undersized conduit for modern operators. Those mid-century gates were never wired for a keypad or app-based opener. Running new low-voltage conduit alongside a 1960s brick pillar without wrecking the brick takes planning. We do it without tearing the pillar apart.
Pricing for Gate Parts & Welding in Hartsdale, NY
Straight numbers: hinge replacement runs $280-$650 per set. Post replacement runs $900-$2,400 depending on soil and post size. Rail repair runs $350-$800. Custom welding starts around $250 for small fixes. A full gate operator retrofit on an older ornamental swing gate, including new settings and a safety photocell, typically runs $1,800-$3,500 in Hartsdale. What moves the number is footing condition, not our mood. We quote the job before we start, and that’s the price. No trip charge inside the county. $40 off any repair over $200. Seniors and veterans get a permanent 10% discount. Call (877) 610-2993 for a free estimate.
We Also Serve Cities Near Hartsdale
We work all around Hartsdale, and we cross into the neighboring towns regularly. Scarsdale, White Plains, Greenburgh, and Irvington are all in our local service area. Same crew, same owner-operator model, same 90-Day Done Right Promise. If you’re a few minutes over the line from Hartsdale, you’ll still get Hal or his crew, not a subcontractor.
Serving Hartsdale, NY - Our Local Coverage Area
We’re based in the Hartsdale area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Hartsdale
If the post itself is out of plumb, the hinge isn’t the root problem. A leaning post in Hartsdale usually means the footing has been heaving in the clay. We level-check the post before we touch a hinge. If it’s moved more than a couple degrees, the fix is a new footing below the 42-inch frost line, not a hinge adjustment. The hinge repair without the footing gives you one summer, maybe. Call (877) 610-2993 and we’ll tell you which one you actually need.
Yes, and we do it regularly in Hartsdale. The existing gate stays; we add or re-engineer the hinge hardware, run new low-voltage conduit where needed, install the operator and keypad, and set the safety photocell. The wall or pillar looks original on the outside. The hard part is usually the wire run, not the operator. Expect $1,800-$3,500 for a full retrofit on a typical Hartsdale ornamental gate. We’ll quote it before we start.
Start with the hinge post. A gate sags from the hinge side, not the middle. Put a level on the gate; if the post is plumb and the gate still drags, then you’re looking at a bent or broken rail. In Hartsdale, with our older gates, it’s usually the post. But if the rail is bowed from years of ice weight, we’ll cut and weld it. We’ll show you which part failed before we sell you anything.
Ice loading. When a Hartsdale ice storm glazes heavy ironwork, the gate can carry hundreds of extra pounds symmetrically until one weld at the hinge boss or mid-rail takes the stress and lets go. Older welds, especially ones done with rod that was too brittle or penetration that was too shallow, fail first. We re-weld with the gate braced square and reinforce the joint plate where the material allows. It’s a fix, not a patch.
If the gate is automated, the entrapment protection requirement doesn’t disappear just because we’re doing hinge work. Under current UL 325 standards, any automatic gate needs functioning safety devices, and any electrical work triggers the requirement. In practical terms, if we’re repairing a gate that has an operator, we’ll check that the photocell and any safety edge are working before we leave. It’s a safety issue, and we won’t hand you back a gate that can close on a child because the sensor was from 1998. Call (877) 610-2993 for an honest answer about your specific setup.
When a Hartsdale Gate Needs a Footing, Not a Patch
Here’s the thing about Hartsdale that most out-of-area contractors miss: all motorized and structural gate work here falls under the Town of Greenburgh’s building department, not a village code. That means the 42-inch frost-line rule is enforced by the town’s inspectors, and it has been for years. But most of the 1930s to 1960s pillar-mounted gates in Hartsdale were installed before anyone was enforcing anything, so their footings sit at 24 inches or less. In the clay-heavy glacial soils between Central Avenue and the Bronx River, a 24-inch footing heaves every winter. The post leans. The gate binds. And a contractor who shows up, replaces the hinge, and drives off will be back the next spring getting an earful from the homeowner. We know because we’ve been called in behind those jobs. The name is on the shop, and the shop is down the road, and that’s the oldest accountability there is.
On a hilly, wooded street near the Hartsdale train station, we replaced a cracked hinge post on a 1950s Tudor’s ornamental wrought-iron swing gate. The original post footing sat at only 22 inches in ledge-fractured clay. We poured a new 48-inch footing, re-welded the hinge post, installed new pintle hinges, and calibrated the existing LiftMaster operator with a safety photocell to meet UL 325 entrapment protection. That’s the whole job in one sentence, and it’s the kind of repair a generic gate parts page won’t prepare you for. Hartsdale’s terrain makes the footing the first question on nearly every older gate we touch. A gate that looks like a simple hinge job almost always has a shifted or cracked footing underneath. Anyone who skips the level check before ordering hardware is guessing.
Call (877) 610-2993 for a free estimate on gate parts and welding in Hartsdale. You’ll talk to a live person. The price gets written down before work starts. And if it’s not done right, Hal Gatewood comes back and makes it right. That’s the promise, and his name is on it.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Hartsdale since 2001.