Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Glen Burnie
If your Glen Burnie gate is sagging, dragging, or won’t close, the problem is almost always in the parts, the welds, or the post underground. We’ll find it, fix it in your driveway, and stand behind it in writing. Gatewood Fence & Gate has been repairing gates since 2001, and Hal Gatewood’s name is on the shop. Call (877) 610-2993 and a live person answers, day or night, not a phone tree.
Glen Burnie keeps us busy with a very specific kind of gate failure. The original gates on those 1950s and 1960s ranchers and cape cods near Marley Creek and Stoney Creek were built to last maybe 30 or 40 years. They’re now 60 to 70. The tidal air does its work quietly, corroding the hinge welds from the inside while the chain-link fabric still looks fine. We know what to look for before you do.
Key takeaways:
- We weld on site in Glen Burnie. Your gate stays in your driveway, not hauled to a shop in another county.
- Upfront pricing. You’ll know the number before we touch a tool, and it won’t change at the door.
- Every job carries the 90-Day Done Right Promise. One call brings us back.
- We answer the phone 24/7. Not a voicemail, not a chatbot, not a call center three states away.
Why Gatewood Fence & Gate Is Glen Burnie’s Preferred Gate Parts & Welding Company
We’ve worked the neighborhoods off Crain Highway, around Marley Station, through South Gate, and up and down Ritchie Highway long enough to know what the salt-laden humidity does to gate hardware. That’s the kind of local knowledge you can’t get from a national outfit reading a script. Hal Gatewood has been owner-operated since 2001, and his address is published. His license number is right there for anyone to look up. The name is on the shop, and the shop is down the road from you. That’s the oldest accountability there is.
We’re certified to service nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We stock the parts Glen Burnie homes actually need, because we already know which hinges, rollers, and latches fail first in this climate. That means faster turnaround, not a two-week wait for a part shipped from somewhere dry and inland.
When you call, a live person answers. Not a recorded greeting. Not a queue. A person who knows gates and knows Glen Burnie.
If you have a written estimate from another company, bring it to us for a free second opinion. Hal will look at it honestly and tell you if they’re selling you work you don’t need. That’s not a gimmick. It’s just how we’ve done business for over two decades.
Our Gate Parts & Welding Services in Glen Burnie
Our Gate Parts & Welding team handles the full range of repair work this area throws at us. Here are the four services Glen Burnie calls for most:
Hinge Replacement
A gate sags in the hinge post, not in the middle, and that is where we start. In Glen Burnie’s tidal air, the hinge welds are the first thing to corrode through, especially on that original 1960s stock. We cut out the old hinge, grind the post clean, weld a new one, and the gate sits level again. A typical hinge replacement in Glen Burnie runs $140-$280 per hinge, depending on gate weight and whether the post itself needs plating.
Post Replacement
Winter freeze-thaw cycles heave gate posts set in shallow or sandy fill, and Glen Burnie has plenty of both. That reclaimed, graded land from the mid-century buildout shifts every winter. We dig out the moving post, set a new one below frost depth in proper concrete, and re-hang the gate. Post replacement here typically runs $320-$620 for a standard residential swing gate post, including concrete and re-hanging. Fix the panel without the post and you’ll fix it twice.
Rail Repair
The top and bottom rails on a tube-frame chain-link gate take the structural load. Once a weld pops at the corner, the whole frame twists, and the gate starts dragging on the pavement. We re-weld on site, straighten what needs straightening, and often add a gusset plate to stop it from happening again. Rail repair on a Glen Burnie driveway gate usually lands between $180 and $360, depending on how far the damage has spread.
Custom Welding
Sometimes a Gate Installation - Glen Burnie project involves a gate built for a specific opening in a specific year, and no off-the-shelf part exists anymore. We fabricate and weld brackets, frame sections, hinge plates, and reinforcements on site, matched to your gate and your property. Custom welding is quoted by the job, but most Glen Burnie repair-oriented welding runs $150-$400. And on the automated side, we can weld and install a Ghost Controls or Linear opener where trenching power isn’t practical, which comes up often on older Glen Burnie lots.
Trusted Brands We Service in Glen Burnie
We service Linear, Viking, Ghost Controls, and DoorKing openers, along with the rest of the major names. Because we’re local to Anne Arundel County and constantly running these exact parts on Glen Burnie gates, we keep the common boards, hinges, rollers, and arms in stock. That means less waiting on a parts truck. If your Viking opener is dead or your Ghost Controls arm won’t engage, call us. We’ll diagnose it straight, show you what failed, and price the fix before doing anything else.
Common Gate Parts & Welding Problems We See in Glen Burnie Homes
- Hinge-weld corrosion near Marley and Stoney Creeks. The tidal-air microclimate eats the weld from the inside out. The gate looks fine right up until the hinge lets go and the panel drops onto the driveway. We see this most on original 1960s chain-link frames.
- Winter post heaving on shallow sandy fill. That reclaimed, graded ground moves. A post set 18 inches deep in sand will walk up every frost cycle. We set posts below frost depth in concrete, then compact clean fill around them.
- Sag correction on narrow lots where a slide gate won’t fit. Along the older streets off Crain Highway, there’s often no room for a slider, so the swing gate has to work. When it’s propped open because it drags, that’s a security problem and a trip hazard. We re-level the hinges and reinforce the post.
- Commercial slide gate roller wear along Ritchie Highway. Those industrial sliders take a beating, and the roller trucks bind, the rail clogs, and the loop detectors and safety photocells start faulting. We source and install commercial-grade rollers built for salt air, not the cheapest thing in the catalog.
Pricing for Gate Parts & Welding in Glen Burnie, MD
You’ll get an exact quote before any work starts. Here’s what Glen Burnie homeowners should expect to pay for common gate parts and welding:
- Hinge replacement: $140-$280 per hinge
- Post replacement: $320-$620 for a standard residential post
- Rail repair: $180-$360
- Custom welding (repair-focused): $150-$400 per job
- Gate roller replacement: $90-$220 per gate
- Latch and lock replacement: $80-$180
What moves the number is how corroded the existing weld points are, whether the post needs to be reset, and how heavy the gate is. We don’t mark up parts. You pay for parts at cost plus labor, quoted upfront. Our standing offers apply in Glen Burnie: $40 off any repair over $200, no trip charge inside the county, free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans. Every price is agreed before we start, and the 90-Day Done Right Promise is in writing on every job. Call (877) 610-2993 for a free estimate.
We Also Serve Cities Near Glen Burnie
Our crews cover Glen Burnie and the surrounding communities: South Gate, Severna Park, Ferndale, and Pasadena. If you’re just over the line in any of those spots, you still get the same live-person phone answer, the same upfront pricing, and the same 90-Day Done Right Promise. There’s no trip charge inside the county, and we’re on the road in and around Glen Burnie every day.
Serving Glen Burnie, MD - Our Local Coverage Area
We’re based in the Glen Burnie area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Glen Burnie
Because the hinge weld is the thinnest, most stressed point on the gate, and Glen Burnie’s tidal air at the head of Marley and Stoney Creeks keeps it damp and salted year round. The galvanized chain-link fabric sheds water and lasts a lot longer than the bare steel weld underneath the hinge. The weld rusts from the inside, and you don’t see it until the gate drops. If your fence fabric looks fine but the gate is suddenly sagging, the hinge is usually about to separate. Call (877) 610-2993 and we’ll check it before it hits the driveway.
Yes, and we do it regularly along the older streets off Crain Highway where a swing gate would block the shared driveway or the sidewalk. We weld the post brackets, set the roller track, and hang the slide gate so it runs tight to the fence line. On the automated side, we install the Glen Burnie Gate Motor & Opener and the required safety photocells and edge sensors. You’ll get a written price before we order anything. Call (877) 610-2993 for a measure and a quote.
The old post comes out, and a new one goes in below frost depth, set in concrete with clean compacted fill around it. The shallow sandy fill on many of these mid-century lots is what’s been moving. Frost depth is deeper than what the original builder used, and that’s the permanent fix. Most post replacements in Glen Burnie run $320-$620, and we keep the gate operational while we do it. Call (877) 610-2993 for an exact quote.
Yes. We prop the gate, brace the frame, and work around whatever access your home needs. Off Crain Highway in a 1960s rancher neighborhood, our tech arrived to a sagging swing gate where the hinge post had rusted through at the weld while the fabric still looked fine. We replaced the hinge post, re-welded the frame, and installed a Ghost Controls solar gate opener because the owner wanted keypad entry without trenching power, keeping the shared driveway open the whole time. That’s how we work every job in Glen Burnie.
Automated sliding gates in Anne Arundel County must have Gate Access Control in Glen Burnie including reversing photocells and a monitored contact edge, and they have to be tested when the operator is installed or significantly serviced. We install and test all of it. We also make sure the gate’s force setting won’t hurt a child or a pet, and we bench-test the controls before we leave. If your gate is older and missing any of that, call (877) 610-2993 and we’ll tell you what it needs.
Call Gatewood Fence & Gate for Gate Parts & Welding in Glen Burnie, MD
If your gate is dragging, sagging, corroding, or just won’t stay latched, call (877) 610-2993 for a free estimate. A live person answers. We’ll come to Glen Burnie, look at the weld, look at the post, and tell you honestly what needs fixing and what doesn’t. The price is agreed before we start. Every job is covered by the 90-Day Done Right Promise. Hal Gatewood’s name is on the shop, and he intends to keep it that way.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Glen Burnie since 2001.