Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Gladeview
Gate post replacement in Gladeview typically runs $450-$900 depending on footing depth and Miami-Dade NOA requirements, while hinge replacement on a standard tubular steel driveway gate usually lands between $180-$320. Most jobs we handle in the 33147 ZIP are completed in one visit, and we quote the full price before any work starts. If your gate is sagging, dragging, or the weld at the hinge has let go, call us at (877) 610-2993 and Hal will talk you through what you’re actually looking at.
We know Gladeview’s streets because we work them. The concrete block homes off NW 79th Street, the side yards along NW 22nd Avenue, the older places tucked back near NW 95th Street where the original iron gates from the 1960s are still hanging on. Those gates tell a story, and usually the story is that nobody has touched the posts in fifty years. We’re the Gate Parts & Welding crew that fixes what’s actually broken instead of selling you a whole new gate you don’t need.
Why Gatewood Fence & Gate Is Gladeview’s Preferred Gate Parts & Welding Company
Hal Gatewood started this company in 2001, and his name is on the shop and on every invoice. He is not a franchise. He’s not a call center. When you call (877) 610-2993, a live person answers, and if you want to drive to the shop and look Hal in the eye before you hire him, that’s fine too. That’s the oldest accountability there is.
We’ve built our reputation in Gladeview one hinge post at a time. Homeowners in this part of Miami-Dade have dealt with plenty of out-of-county contractors who don’t understand what unincorporated county jurisdiction means for a gate job. We do. We know that a post replacement off NW 15th Avenue can trigger a Miami-Dade NOA review, and we handle the paperwork before we ever fire up the welder. Every job carries our written 90-Day Done Right Promise: if it’s not done right, one call brings Hal back. No fine print, no runaround.
We’re licensed and insured, and every person who shows up in Gladeview is background-checked and uniformed. We stock parts locally for the older operators still running in Gladeview, so we’re not waiting a week on a shipping delay for a control board that went obsolete in 2004. The name is on the shop, and the shop is down the road. That matters.
Our Gate Parts & Welding Services in Gladeview
Hinge Replacement
Hinge replacement on a Gladeview driveway gate typically runs $180-$320 per pair, depending on gate weight and whether the hinge is welded or bolted. On the original wrought iron gates around 33147, we usually find the hinge weld has rusted through while the hinge itself is still technically fine. We cut out the old weld, clean the mounting surface, and weld in new hinges on site. The gate stays in your driveway. We don’t haul it off to a shop and bring it back a week later.
Post Replacement
This is the big one in Gladeview, and it’s where Miami-Dade’s NOA system really matters. Post replacement on a swing gate in this area generally runs $450-$900, and the range depends almost entirely on footing depth. Homes built in the 1950s through 1970s often have posts set only 18 to 24 inches deep. Miami-Dade wind-load specs require much more than that, especially for an automated gate. When we replace a post in Gladeview, we trench a proper footing, pour to county spec, and weld the new steel post to the existing gate frame so everything lines up. If the post is leaning and the gate is welded to it, we cut the gate free, set the new post, and reweld. It’s more work than a hinge swap, but it’s the only way to do it once.
Rail Repair
Bottom rails on older tubular steel gates in Gladeview rust through from the inside out. Year-round humidity and salt-laden air from Biscayne Bay do a number on uncoated steel, and the lower rail is where the water sits. Rail repair ranges from $150-$350 depending on how much of the rail has corroded and whether we can splice in a new section or need to replace the full length. We weld in matching steel, grind it smooth, and repaint so the repair doesn’t look like a patch job.
Custom Welding
Sometimes the gate is still good but the design no longer works for how you live. Custom welding in Gladeview starts around $200 for small modifications like adding a latch point or reinforcing a weak section, and goes up from there for larger fabrication work. We weld on site, so you can watch the work happen and point to exactly what you want changed. If you need something built that doesn’t exist off the shelf, we’ll build it. Hal has been welding since before half the gates in Gladeview were installed.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Gladeview
We work on Linear, Viking, and DoorKing operators regularly in Gladeview, along with six other major brands. The original equipment on many 33147 gates is a Linear or DoorKing from the 1990s, and we still stock parts for those legacy units rather than telling you the only answer is a full replacement. Sometimes replacement is genuinely cheaper. We’ll tell you honestly which one you’re looking at, and you’ll never hear us push a new operator you don’t need. For common operator parts like control boards, limit switches, and receivers, we keep inventory in the county, so a repair in Gladeview usually happens same week, not same month.
Common Gate Parts & Welding Problems We See in Gladeview Homes
- Shallow footings from the original build. Posts set 18 to 24 inches deep in sandy soil can’t hold a gate against Miami-Dade wind loads. Once the gate starts sagging, the post is already moving. Re-posting is the real fix, and it means concrete work, not just welding.
- Rust-through at hinge welds and lower rails. The humidity and salt air in Gladeview eat uncoated steel from the unprimed inside surface. By the time you see bubbling paint on the outside, the metal underneath is often already perforated.
- Heaving after heavy summer rain. Gladeview’s flat, low-lying terrain means water sits in the soil longer than it does in higher ground. Gate posts set in seasonally saturated sand tilt and shift, throwing swing gates out of plumb and jamming slide gate rollers.
- Legacy operators without modern safety edges. Plenty of 1990s-era Linear and DoorKing units in Gladeview are still running with original control boards and no photocell input wired correctly. When an old operator won’t reverse on obstruction, that’s a safety issue, not just an annoyance, and it needs attention before someone gets hurt.
Pricing for Gate Parts & Welding in Gladeview, FL
Here is what Gladeview homeowners can expect to pay for the most common gate parts and welding work:
| Service | Typical Range in Gladeview |
|---|---|
| Hinge replacement (welded pair) | $180 - $320 |
| Post replacement (with concrete footing to Miami-Dade spec) | $450 - $900 |
| Bottom rail repair (rust-through, splice or replace) | $150 - $350 |
| Custom welding (small modifications) | $200 - $500 |
| Safety photocell retrofit (parts and labor) | $180 - $400 |
The biggest cost variable in Gladeview is footing depth. A replacement post that can go into an existing concrete footing costs less than one that requires new concrete work to meet Miami-Dade wind-load specs. We tell you which one you have before we quote, and the number we give you is the number you pay. Nothing gets added at the door. Every quote is free, and we offer $40 off any repair over $200 and no trip charge inside the county.
We Also Serve Cities Near Gladeview
Our crews work throughout the corridor around Gladeview and into the neighboring communities of West Little River, Pinewood, Westview, and Allapattah. If you’re in one of those areas and your gate is giving you trouble, the same 90-Day Done Right Promise applies, and the same live person answers when you call.
Serving Gladeview, FL - Our Local Coverage Area
We’re based in the Gladeview area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Gladeview
Because Gladeview is an unincorporated enclave of Miami-Dade County, not an incorporated city with its own building department. Structural gate work, including post replacement and structural welding, falls under the county’s NOA product-approval system, the same hurricane-load compliance framework applied to impact windows and doors. Neighboring incorporated cities like Hialeah and Miami Gardens have different permit paths. We handle the paperwork so the job doesn’t stall mid-project. Call (877) 610-2993 and we’ll tell you upfront whether your job triggers NOA review.
It depends on how much of the rail is gone. If the rust is localized, we can cut out the bad section and weld in a new steel rail for roughly $150-$350. If the entire lower frame is perforated, you’re welding onto structurally compromised steel, and replacement starts to look cheaper. We’ll show you the metal after we clean it up so you can see what we’re seeing, then you decide. Estimates are free.
In most Gladeview cases we inspect, it’s the post. The sandy, seasonally saturated soil around 33147 lets posts heave and tilt after intense summer rain, and original footings from the 1960s are often only 18 inches deep. The hinges may look worn, but the post is the root of the problem. We can correct it with a proper re-post and reweld, and the gate will swing clean again. Call us and we’ll come take a look.
Yes. Retrofitting safety photocells onto a legacy Linear or DoorKing operator in Gladeview typically runs $180-$400 including parts and labor, depending on wiring access and control board compatibility. Many 1990s boards have a photocell input that was never connected when the gate was originally installed. We wire in the cells, align them to the gate’s sweep, and test the reverse function before we leave. If the board is too old to accept a proper safety input, we’ll tell you that too, and quote a control board replacement instead of pretending a workaround is safe.
We cut the gate free, remove the old post and its shallow footing, pour a new concrete footing to Miami-Dade wind-load spec, set a new steel post, and reweld the gate to the new post. This is the most involved post replacement scenario, typically $700-$900 in Gladeview depending on gate size. The alternative, leaving the gate welded to a moving post, just lets the problem get worse and eventually destroys the gate frame. Better to do it once, correctly, with a written 90-Day Done Right Promise behind the work.
Get a Straight Answer About Your Gladeview Gate
If your gate is sagging, rusted through, or just not latching the way it used to, call us at (877) 610-2993. Hal or one of his crew will answer, ask you a few questions, and tell you what you’re probably dealing with before anyone drives out. The estimate is free, the price is set before work starts, and the 90-Day Done Right Promise is in writing. If it’s not done right, we make it right. That’s the deal in Gladeview and everywhere else we work.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Gladeview, FL since 2001.