Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Fontana
Gate parts and welding in Fontana usually means one of three things: a hinge post that’s torqued loose from Cajon Pass wind, a roller that’s jumped its track on a warehouse gate, or a builder-grade operator that quit years before it should have. We fix all three, and we do it on site. Our Gate Parts & Welding crew serves the whole of Fontana, from the 92336 and 92337 tracts south of the 10 to the older 92335 neighborhoods west of Sierra. Call (877) 610-2993 and you’ll get a live person, not a voicemail.
Why Gatewood Fence & Gate Is Fontana’s Preferred Gate Parts & Welding Company
We’ve been working Fontana long enough to know what this wind does to a gate. The Cajon Pass funnels gusts straight down into the city, and we see the results weekly: sagging single-leaf driveway gates in Southridge, bent hinge posts in West End tract homes, and commercial rollers ground flat on Cherry Avenue. Homeowners here don’t need a company that’s just learning the zip codes. They need someone who knows that a gate in 92336 fails differently than a gate in Rialto, three miles west.
Our reputation in Fontana rests on showing up when we say we will and fixing the gate in your driveway, not hauling it off to a fab shop somewhere. The name on the invoice is Hal Gatewood’s. The 90-Day Done Right Promise is on every job we write. If a weld cracks or a hinge starts sagging again within 90 days, call us. One call and we make it right. That’s the whole promise, in writing, not buried in fine print.
We answer the phone 24 hours a day, 7 days a week. You call, a person picks up. Same goes for the crew that arrives in Fontana: background-checked, uniformed, and they’ll know the difference between a south-facing gate that thermal-expanded in July and one that a truck clipped on a windy Tuesday.
Our Gate Parts & Welding Services in Fontana
Hinge Replacement
Fontana’s wind loads turn hinge replacement into more than a swap job. A hinge that’s fine in Ontario can be torqued 15 degrees out of plumb here after a single high-wind event. We remove the old hinge, check the post for fatigue cracks, and weld in heavier-gauge hardware when needed. A gate sags in the hinge post, not in the middle, and that’s where we start. Most residential hinge replacements in Fontana run $180-$420 depending on gate weight and whether the post needs reinforcement.
Post Replacement
This is the service Fontana calls for more than almost any other. Wind gusts through the Cajon Pass push against a gate leaf like a sail, and over years that pressure loosens the post footing until the whole assembly leans. We dig out the old footing, re-set the post in concrete to the proper depth for our soil, and re-hang the gate square. In the 92336 corridor especially, we see posts that were set too shallow by original builders. Post replacement in Fontana typically runs $450-$900 for residential, more for heavy sliding commercial posts along Slover Avenue and the I-10 frontage roads.
Rail Repair
Sliding gate rail is a wear item in this city. The warehouse district around Cherry Avenue and the 10/15 interchange runs some of the densest truck traffic in the country, and a sliding gate rail that’s even slightly bowed will derail under daily semi-truck cycles. We cut out the damaged rail section, weld in new track, and re-square the rollers so the gate travels true. For residential cantilever gates, rail repair is usually $250-$550. On commercial rolling steel gates, the job is bigger and priced by the foot, but we quote it before we touch it.
Custom Welding
Plenty of older Fontana homes are adding wrought-iron driveway gates as retrofit security, and those jobs need custom fabrication, not a catalog piece. We can extend a gate leaf, build a matching section to fill a wider opening, weld decorative pickets back after an impact, or add brackets for an operator. Custom welding starts around $150 and goes up based on materials and scope. You’ll get a written number before the welder fires up.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Fontana
We work on Linear swing operators, Viking and DoorKing commercial operators, and Ghost Controls kits that homeowners installed themselves. Fontana’s builder-grade Linear units in HOA communities from the 1990s and early 2000s are hitting end-of-life at the same time, which makes parts availability a real issue if you’re calling a generalist. We keep common boards, limit switches, and rollers on the trucks that serve this area, so we’re not ordering a part and making you wait another week. We also know these brands well enough to tell you honestly when a controller isn’t worth fixing and a heavy-duty replacement is the cheaper long-term call.
Common Gate Parts & Welding Problems We See in Fontana Homes
- Wind-torqued hinge posts. The Cajon Pass wind corridor is the single biggest gate killer in Fontana. Sustained gusts push a gate leaf sideways, and over time the post twists in its footing. We see this constantly in newer subdivisions off Citrus and Sierra where original posts were set for mild coastal conditions, not for what Fontana actually dishes out.
- Builder-grade operators burning out early. Communities built in the 1990s and 2000s HOA boom often came with the cheapest operator the builder could install. Those units don’t tolerate three or four windy days a month where the motor fights sustained gusts. They burn out. We replace them with heavier-duty equipment that’s matched to the load.
- Thermal mis-calibration. Triple-digit summer heat in Fontana makes steel gate panels expand, which throws limit switches out of calibration. The gate stops mid-cycle, reverses for no reason, or slams shut. Our fix is a recalibration and, where needed, a limit-switch replacement so the gate reads its stops correctly in both July and January.
- Roller and track failure on sliding gates. On distribution-center sliding gates along Cherry and Slover, heavy-gauge rollers wear fast under semi-truck traffic. When a roller fails or the track bows, the gate derails, and a single down gate can hold up a whole afternoon shift. We stock heavy-gauge roller hardware and commercial components precisely because the volume of truck traffic here demands it.
Pricing for Gate Parts & Welding in Fontana, CA
Here’s what you can expect to pay in Fontana. Hinge replacement runs $180-$420. Post replacement runs $450-$900 for residential, higher for commercial sliding posts. Rail repair runs $250-$550 for homes, and commercial rolling steel gates are quoted by the job since the rail length and gauge vary so much. Custom welding starts around $150 for a bracket or small repair and goes up for full gate fabrication or structural work.
Three things affect your price here: the weight of the gate, whether the post footing needs re-set, and if the gate is on the south side where summer heat expansion is worst. We quote every job before work starts. You will not see a bigger number at the door. Estimates are free, we don’t charge a trip fee inside the county, and as a local business we extend 10% off to seniors and veterans year-round. Call (877) 610-2993 and we’ll put a number on it.
We Also Serve Cities Near Fontana
Our crews work throughout Fontana and the surrounding area every week. That includes Bloomington, Rialto, Glen Avon, and Pedley. If you’re just over the city line and wondering whether we’ll come out, the answer is yes, and the trip charge inside the county is zero.
Serving Fontana, CA - Our Local Coverage Area
We’re based in the Fontana area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Fontana
Southridge sits squarely in the path of the Cajon Pass wind corridor, and sustained gusts torque hinge posts in ways that neighborhoods to the west don’t experience. The fix starts with checking the post itself. If the footing has loosened, replacing the hinge alone just moves the strain somewhere else. We reinforce the post, re-set it if needed, and then install hinges sized for the gate’s actual wind load. Call (877) 610-2993 for a free estimate.
Yes, and we do it often, especially in central and west Fontana where mid-century homes are adding driveway gates as retrofit security. The job usually includes mounting the operator, running power, and installing safety edges or photo-eyes. If the gate was never built with a rack or operator bracket, we weld those on. A homeowner-supplied Ghost Controls kit can work, but we also install heavier Linear units that suit our wind. We quote the full job before starting.
We re-square the post footings, replace bowed rail, and upgrade to heavy-gauge rollers built for the weight and cycle count these gates see. A gate on Cherry Avenue can cycle fifty or sixty times in a single shift, so the hardware that works on a residential slider won’t last here. We also recalibrate the loop detectors so the gate doesn’t close early on a semi. We’ve done this exact repair more than once, including a job where a wind gust pushed a truck into a gate and the original DoorKing operator had been fighting the misalignment for months. Fixed before the afternoon shift change.
For Fontana, it’s common but not normal. Triple-digit summer heat expands the steel in the gate panel, which shifts the physical stops and throws the limit switches off. We see it every summer on south-facing gates especially. The lasting fix is usually new limit switches plus a proper gap setting that accounts for thermal expansion, so the gate doesn’t slam or stop mid-cycle in July or January. We’ll inspect and recalibrate it in one visit.
We do. Older homes in 92335 and surrounding blocks are increasingly adding wrought-iron driveway gates, and those usually need custom fabrication to match the existing fence or fit a nonstandard opening. We can weld a new gate from scratch, extend an existing panel, or add pickets and security brackets to a gate that’s already there. Every custom job is quoted up front, with the 90-Day Done Right Promise on the steel and the welds both.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving the Inland Empire since 2001.