Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Federal Heights
If your gate in Federal Heights is sagging at the latch, dragging on the driveway, or the hinges are so corroded they’re about to snap, here’s the straight answer: most gate parts and welding repairs in Federal Heights run $180 to $640 depending on whether we’re replacing a hinge, resetting a post in concrete, or re-welding a twisted frame. We show up with the welding rig in the truck and fix it where it stands, usually the same day you call. That’s what we’ve been doing since 2001. Call (877) 610-2993 and a live person answers, day or night.
Why Gatewood Fence & Gate Is Federal Heights’s Preferred Gate Parts & Welding Company
Hal Gatewood started this shop in 2001 and his name is still on every invoice. That matters in Federal Heights, where the housing stock is original 1950s and 1960s ranches with the original galvanized chain-link gates still swinging on the same hinge posts. We’re not a franchise that reads from a script. We’re the crew that knows why the gate at 84th and Pecos is binding differently than the one three blocks west near the rec center.
Federal Heights homeowners call us because we repair first and replace only what’s actually failed. If a weld seam has split, we re-weld it on site. If a post has heaved out of plumb from the clay soil, we dig it out, set it deeper, and brace it properly. We don’t swap a whole gate because one hinge is shot. That repair-first habit is why folks around Sherrelwood, Welby, and Shaw Heights tell their neighbors to call us when a gate goes bad.
Every job carries our 90-Day Done Right Promise in writing. If it’s not right, one call brings Hal back. No runaround, no “that’s the fault of the soil.” And every call is answered by a live human, 24 hours a day, seven days a week. Not a voicemail box. Not a menu tree. You call, somebody real picks up.
Our Gate Parts & Welding Services in Federal Heights
Hinge Replacement
Original hinges on 1950s-era Federal Heights gates are usually galvanized steel that’s been through 60-plus Colorado winters. The freeze-thaw cycling pits the metal, the pivot wears into an oval, and then the gate drops half an inch and stops latching. We cut the old hinge off with the torch, weld a new one on, and realign the gate so it closes square. Most hinge replacements on residential swing gates in Federal Heights run $180 to $340, including the part and the welding.
Post Replacement
This is the one Federal Heights sees more than anywhere else in the north metro. The ground under those 1950s ranch lots is clay-heavy, and it heaves every winter. A post set 18 inches deep in 1962 is now leaning 4 degrees out of plumb, and no amount of hinge adjustment will fix a gate when the post is the thing that moved. We dig out the old post, set a new steel post deeper in concrete, and weld or bolt the gate back to it. Post replacement with concrete work typically runs $350 to $640 in Federal Heights depending on gate width and soil conditions.
Rail Repair
Tube-frame gates get bent rails from kids climbing them, from wind slamming them open, and from mail carriers giving them a nudge with the bumper. A bent top rail puts uneven stress on every weld in the frame, and within a year you’ll hear cracking at the seams. We straighten what’s salvageable, splice-weld new tube where it’s not, and repaint the repair so it doesn’t flash rust. Rail repair and frame straightening usually falls between $220 and $450.
Custom Welding
Some Federal Heights gates aren’t worth replacing because the frame is still solid, but the hinge tabs are gone, or the latch plate has torn off, or a previous “repair” left a mess of booger welds we have to grind out and redo. Hal welds on site with a mobile rig, so your gate stays in your driveway where the fit-up is exact. Custom welding starts at $120 for small repairs and runs up from there based on actual torch time and material.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Federal Heights
When a motor or operator is involved, we service FAAC, BFT, Linear, and Viking among the nine major brands we’re certified on, including LiftMaster, Ghost Controls, and Mighty Mule. We keep common parts for these operators in the truck, so a Federal Heights call usually means one visit, not three. If there’s a longer lead time on a specific control board, we’ll tell you that before we touch anything, and the price is agreed before the work starts.
Common Gate Parts & Welding Problems We See in Federal Heights Homes
- Heaved hinge posts on 1950s ranch lots. The clay soil under Federal Heights swells and shrinks with over 100 freeze-thaw cycles a year. Posts set shallow 50 or 60 years ago lean a little more every March, and the gate starts swinging into the latch post instead of into the latch.
- Corroded weld seams on galvanized tube frames. The original chain-link gates in Federal Heights were welded with mild steel and dipped as a unit. Sixty years of frost and road salt have eaten through at every seam, especially near the bottom rail where water pools. We weld those seams back up or replace the tube section entirely.
- Wind-bent rollers on Federal Boulevard commercial sliders. The north-south wind that channels down the Federal Boulevard corridor hits sliding chain-link security gates at the shops and light industrial lots. Bottom rollers bend, the gate twists, and then it binds halfway across the opening. We straighten frames and swap rollers regularly on that strip.
- Latch and lock failures from sag-induced misalignment. By early spring, a gate that closed fine in October is an inch too low at the latch. People force the latch, which bends the keeper, which makes the sag worse. We fix the sag first, then replace or re-align the latch. Fixing the panel without the post and you’ll fix it twice.
Pricing for Gate Parts & Welding in Federal Heights, CO
Here’s what Federal Heights homeowners should expect, in real numbers:
- Hinge replacement: $180-$340 per hinge, welded on site
- Post replacement with concrete: $350-$640 per post
- Rail repair and frame straightening: $220-$450
- Custom welding (latch plates, hinge tabs, crack repair): $120 and up
- Gate roller replacement on sliders: $160-$390
Every price is quoted and agreed before any work starts. Not an estimate that might creep. Hal looks at the gate, tells you what it costs, and writes it down. We also keep standing offers that don’t require asking: $40 off any repair over $200, no trip charge inside the county, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 and we’ll give you a straight number.
We Also Serve Cities Near Federal Heights
Our crew covers Federal Heights and the surrounding communities, including Sherrelwood, Welby, Shaw Heights, and down the road into Westminster. Scheduling runs from our Denver office, but the person who shows up at your gate is local and knows these neighborhoods. You can read more about our broader service area on the Gate Parts & Welding in Federal Heights page or the Gate Parts & Welding service page.
Serving Federal Heights, CO - Our Local Coverage Area
We’re based in the Federal Heights area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Federal Heights
Federal Heights sits on clay-heavy soil that heaves dramatically through the winter, and most of the residential gates here are original 1950s-to-1970s installations set in shallow concrete footings. Westminster has more newer construction with deeper posts and lighter materials. In Federal Heights, the gate doesn’t bend; the post moves. We fix it by resetting the post deeper and bracing it properly, which Westminster gates rarely need. Call (877) 610-2993 and Hal can tell you over the phone whether it’s the post or the hinge based on how you describe the sag.
Yes. We do it weekly. The frame tube is usually still solid; it’s the welds, hinges, and post footings that fail. Hal re-welds the seams in place, replaces the hinges, and resets posts as needed. You’ll get another 20 years out of a galvanized tube gate that a chain outfit would have scrapped and swapped for aluminum. The price is quoted before we start, and the 90-Day Done Right Promise covers the work in writing.
Yes. The Federal Boulevard corridor funnels north-south wind straight down the arterial, and the sliding chain-link security gates at the auto shops and industrial lots catch that wind broadside. Bottom rollers bend, frames twist, and gates bind. We straighten the frame, replace the bent rollers with heavier-duty units, and often add a mid-span roller to carry the load. Call (877) 610-2993 for a free estimate, and we’ll come look at the gate before a tenant’s truck backs into it.
Ask whether it has monitored safety photocells and whether the force settings are compliant with UL 325, the standard that applies to gate operators. Many original Federal Heights installations predate photocell requirements, and an older operator without working safety edges can crush a child or a dog. Hal tests the photocells, checks the reversing sensitivity, and will tell you plainly if the operator belongs in the scrap pile. Camera system integration is fine, but start with the safety gear. Call (877) 610-2993 and we’ll inspect it.
Yes, we’ve installed solar-powered gate operators for acreage properties on the edges of Federal Heights, where running mains power to the gate would cost several times the operator itself. A solar panel and battery bank run a FAAC or Viking swing operator cleanly, and we size the system for the gate’s actual weight and daily cycle count. For those jobs, we come out, measure, and give you a written price, and then we schedule the install. No same-day dispatch on a solar install; it’s measured and built right. Call (877) 610-2993 for a free site visit.
If your gate is sagging, binding, or the hinges look like they belong on a museum piece, call Gatewood Fence & Gate at (877) 610-2993. A live person answers, the estimate is free, and the price is written down before we ever strike an arc.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Federal Heights and the north Denver metro since 2001.